Измельчитель insinkerator evolution 250 инструкция

Evolution 250 Food Waste Disposer

Product Information

Specifications

• Power: 220-240V, 50-60Hz
• Model: 78174 Rev E

Description

The food waste disposer is an environmentally responsible
alternative to transporting food waste to landfills. It can help
reduce greenhouse gas emissions and can be recycled to produce
renewable energy and fertilizer at capable wastewater treatment
plants.

Installation

Before installing the disposer, read through the entire
installation manual. Make sure you have all the necessary tools,
materials, and accessories. The installation must comply with
AS/NZS 3500.2 standard requirements. In Australia, all plumbing and
electrical work must be completed by a qualified tradesperson and
may require approval from the relevant regulator and/or sewerage
system operator.

Tools & Materials You Will Need:

• Slotted Screwdriver
• Adjustable Pliers
• Safety Glasses

Tools, Materials, and Accessories You May Need:

• Phillips Screwdriver
• Drain Auger
• 9.5 mm Electrical Clamp
• 38 mm Drain Trap
• 33 mm Hole Drill
• Hammer
• Hacksaw
• Water Hose Clamp
• Pipe Wrench
• Copper Earth Wire
• Dishwasher Drain Connection Kit
• Electrical On/Off Switch
• Drain Tube Extension

Parts List

• MOUNTING ASSEMBLY

  • Strainer Basket and Plug with Cover (Evolution Models 250 &
    150, Model E75)

  • Strainer Basket and Plug (Evolution Models 100 & 200, Model
    BW5)

  • Stainless Steel Stopper (Model 66, BW4)

  • Sink Flange

  • Rubber Gaskets (2)

  • Fiber Gasket (optional)

  • Backup Flange

  • Mounting Ring

  • Screws (3)

  • Snap Ring

• DISPOSER

  • Sound Baffle (Evolution Models, Models 66, 56, BW5, BW4, BW3,
    E75)

  • Mounting Gasket

  • Lower Mounting Ring

  • Dishwasher Inlet

  • Discharge Outlet

  • Wrenchette

• DISCHARGE ASSEMBLY #1 (Evolution Models, Model BW5)

  • Hose Clamp
  • Elbow Discharge Tube (38 mm diameter)
  • Straight Discharge Tube (optional)

• DISCHARGE ASSEMBLY #2 (Models 66, 56, 46, BW5, BW4, BW3, BW2,
  E75)

  • Straight Discharge Tube (optional)
  • Bolts (2) 13 mm 1/4-20 UNC
  • Rubber Gasket
  • Metal Flange
  • Elbow Discharge Tube (38 mm diameter)

• AIR SWITCH (Evolution models, Models 66, 56, BW5, BW4, BW3,
  E75)

  • Air Switch Assembly
  • Tube

Product Usage Instructions

Step 1: Preparing for Installation

1. Read all safety messages before proceeding.

2. Gather all necessary tools, materials, and accessories listed
in the manual.

Step 2: Installation

Follow the step-by-step instructions provided in the
installation manual to properly install the food waste disposer.
Ensure that the installation is allowed by the authorities in your
area.

Step 3: Operation

Once the disposer is installed, follow these guidelines for its
operation:

Normal Operation:

1. Turn on the water faucet.

2. Start the disposer by turning on the electrical switch or
activating the air switch.

3. Slowly feed small amounts of food waste into the
disposer.

4. Allow the disposer to grind the food waste until it is
completely processed.

5. Continue running water for a few seconds after turning off
the disposer to flush out any remaining waste.

Evolution Models:

Due to the finer grinding capability of Evolution models, it may
take slightly longer to grind certain types of food waste.

For Evolution 200/250 models, there may be a fractional second
delay when starting the disposer due to the microprocessor. This is
normal.

Step 4: Maintenance

Regular maintenance is essential for optimal performance and
longevity of the food waste disposer. Follow these maintenance
tasks:

Cleaning:

1. Turn off the electrical switch or air switch and disconnect
power to the disposer.

2. Use a soft brush or cloth to clean the exterior surfaces of
the disposer.

3. Run cold water through the disposer while it is turned on to
flush out any remaining waste.

4. For stubborn odors, grind ice cubes or citrus peels in the
disposer.

Maintenance Tips:

– Avoid grinding hard materials such as bones, shells, or fruit
pits.

– Do not pour grease or oil into the disposer.

– Keep non-food items, such as utensils or metal objects, out of
the disposer.

– Regularly inspect and tighten mounting assembly connections if
necessary.

FAQ (Frequently Asked Questions)

Q: Can I install the food waste disposer myself?

A: In Australia, all plumbing and electrical work must be
completed by a qualified tradesperson. Please consult a
professional for installation.

Q: Does the disposer require any special approval?

A: The disposer may require approval from the relevant regulator
and/or sewerage system operator in your area. Check with the
authorities before installation.

Q: Why does it take longer to grind food waste with Evolution

models?

A: Evolution models grind food waste much finer than other
disposers, resulting in a slightly longer grinding time for certain
types of waste.

Q: Why is there a delay when starting the Evolution 200/250

models?

A: The Evolution 200/250 models have a microprocessor that
causes a fractional second delay when starting. This is normal and
does not indicate a malfunction.

1

3

FOOD WASTE DISPOSER INSTALLATION AND USE MANUAL
3.1
1a

1b

9

15

22

16

1c

10

23

2

11

3
4 5 6
7 8
www.insinkerator.com ©2020 InSinkErator, a business unit of Emerson Electric
Co. All Rights Reserved.

12 17 13
18 19 20 14 21

220-240V, 50-60Hz

78174 Rev E

FOOD WASTE DISPOSER INSTALLATION AND USE MANUAL
Food waste disposers can provide an environmentally responsible alternative to
transporting food waste to landfills. And they can help reduce greenhouse gas
emissions. At capable wastewater treatment plants, food waste can be recycled
to produce renewable energy. Additionally, capable wastewater treatment plants
can process food waste into fertilizer. (Check the plant in your area).
Read through the entire installation manual before installing the disposer.
Determine which of the tools, materials, and accessories you will need before
! you begin. Make sure you have all necessary disposer parts before installing
the disposer.
NOTE: The Evolution models and Model BW5 grind much finer than any other
disposer. For this reason you may notice that it takes a little longer to
grind some food waste. Due to the Evolution 200/250 model’s microprocessor,
users will experience a fractional second delay when starting on all Evolution
200/250 models. This is completely normal.
NOTE: In Australia, all plumbing and electrical work must be completed by a
qualified tradesperson. This product may require approval of the relevant
regulator and/or the sewerage system operator. Disposer must be installed to
AS/NZS 3500.2 standard requirements. NOTE: Make sure that the installation of
this appliance is allowed by the authorities.
TOOLS & MATERIALS YOU WILL NEED: Slotted Screwdriver, Adjustable Pliers,
Safety Glasses TOOLS, MATERIALS, AND ACCESSORIES YOU MAY NEED: Phillips
Screwdriver, Drain Auger, 9.5 mm Electrical Clamp, 38 mm Drain Trap, 33 mm
Hole Drill, Hammer, Hacksaw, Water Hose Clamp, Pipe Wrench, Copper Earth Wire,
Dishwasher Drain Connection Kit, Electrical On/Off Switch, Drain Tube
Extension
PARTS LIST (May vary depending on model)

MOUNTING ASSEMBLY 1a. Strainer Basket and Plug
w/ Cover (Evolution Models 250 & 150, Model E75) 1b. Strainer Basket and Plug
(Evolution Models 100 & 200, Model BW5) 1c. Stainless Steel Stopper (Model 66,
BW4) 2. Sink Flange 3. Rubber Gaskets (2) 4. Fiber Gasket (optional) 5. Backup
Flange 6. Mounting Ring

7. Screws (3) 8. Snap Ring
DISPOSER 9. Sound Baffle
(Evolution Models, Models 66, 56, BW5, BW4, BW3, E75) 10. Mounting Gasket 11.
Lower Mounting Ring 12. Dishwasher Inlet 13. Discharge Outlet 14. Wrenchette

DISCHARGE ASSEMBLY #1 (Evolution Models, Model BW5) 15. Hose Clamp 16. Elbow
Discharge Tube
(38 mm diameter)
17. Straight Discharge Tube (optional)

DISCHARGE ASSEMBLY #2 (Models 66, 56, 46, BW5, BW4, BW3, BW2, E75) 17.
Straight Discharge
Tube (optional) 18. Bolts (2) 13 mm 1/4-20 UNC 19. Rubber Gasket 20. Metal
Flange 21. Elbow Discharge Tube
(38 mm diameter)

AIR SWITCH (Evolution models, Models 66, 56, BW5, BW4, BW3, E75) 22. Air
Switch Assembly 23. Tube

! Read all safety messages before proceeding

SAFETY SYMBOLS NOTICE

Warning indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Caution indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
Notice is used to address practices not related to personal injury.

InSinkErator 471 Mountain Highway Bayswater Vic 3153, Australia Sales Tel: 61
03 9720 5599 Service Tel: 1 300 136 205 www.insinkerator.com.au

Parex Industries Ltd. 5 Tolich Place, Henderson Auckland, New Zealand 0610
Service and Sales Tel: 0800 200 510 Website: www.insinkerator.co.nz

InSinkErator Emerson Electric Co. 4700 21st Street Racine, WI 53406-5093 USA
Sales/Service Tel: 262-554-3652
www.insinkerator.com/worldmap.html

(Evolution) 200-3B, 250-3

33.0 cm 18.5 cm 6.4 cm 23.4 cm 16.8 cm

(Evolution) 100-3B, -11B, 150-3 31.1 cm 17.1 cm 6.4 cm 22.2 cm 16.8 cm

Model 66-3, -10, E75-3

31.8 cm 16.6 cm 6.5 cm 20.0 cm 13.1 cm

Model 56-3, -10, -11

30.8 cm 16.6 cm 6.5 cm 19.4 cm 13.1 cm

Model 46-3, -10

30.8 cm 16.6 cm 6.5 cm 18.9 cm 13.1 cm

BW5 -10

31.1 cm 17.1 cm 6.4 cm 22.2 cm 16.8 cm

BW4 -10

31.8 cm 16.6 cm 6.5 cm 20.0 cm 13.1 cm

BW3 -10

30.8 cm 16.6 cm 6.5 cm 19.4 cm 13.1 cm

BW2 -10

30.8 cm 16.6 cm 6.5 cm 18.9 cm 13.1 cm

2

2.1

2.2

1 CHECK INSTALLATION DIMENSIONS
1. Disposer height. 2. Distance from bottom of sink bowl to centerline of
discharge outlet. (Add
12 mm when stainless steel sink is used.) 3. Distance from centerline of the
discharge outlet to end of discharge tube. 4. Disposer width. 5. Distance from
disposer vertical centerline to centerline of trap connection.
NOTICE
To properly drain and prevent standing water in the disposer, the waste pipe
entering the wall must be lower than the disposer discharge outlet.
2 DISCONNECT AND CLEAN SINK DRAIN
PERSONAL INJURY Wearing safety glasses is recommended during the installation
of the food waste disposer.
DISCONNECT SINK DRAIN 1. Loosen nuts (1) at top of trap (4) with pipe wrench.
Remove trap.
(See Figure 2.1) 2. Loosen nut (2) at top of extension pipe. Remove extension
pipe. 3. Remove nut (3) at base of sink flange. 4. Push strainer up through
sink hole and remove it. (See Figure 2.2) 5. Clean sink flange area of any
putty or other debris.
NOTE: The sink hole may have to be enlarged to accept the disposer sink
flange. Sink hole enlargement tools are available from your InSinkErator
dealer. CLEAN SINK DRAIN Failure to clean sink waste pipe line may result in
waste pipe blockage. With drain auger, clear away all hardened waste material
in horizontal drain line running from drain trap to main pipe. When installing
in new construction, cleaning the sink waste pipe line is not necessary.
IF REPLACING AN EXISTING DISPOSER, CONTINUE WITH INSTRUCTION 3.
IF THIS IS A FIRST TIME INSTALLATION, SKIP AHEAD TO INSTRUCTION 4.

3.2
3.3
3.4
3 REMOVE EXISTING DISPOSER
PERSONAL INJURY To avoid personal injury, do not position your head or body
under disposer; the unit could fall during installation.
ELECTRICAL SHOCK · To avoid electrical shock, disconnect power before removing
any existing
disposer. Turn off electrical power at fuse box or circuit breaker or if
equipped unplug disposer electrical power plug from wall outlet. · Improper
connection of equipment earth (grounded) conductor can result in electric
shock.
1. If your disposer is equipped with an electric plug and cord connection,
unplug power plug from electrical wall outlet. If your disposer is not
equipped with an electrical plug and cord connection, contact an electrician
to disconnect the old disposer plus install an earth (grounded) electrical
wall outlet for the new disposer connection that must be compliant to all
local electrical codes.
2. Disconnect drain trap from disposer waste discharge tube with adjustable
pliers (see Figure 3.1). Also disconnect dishwasher drain connection, if
applicable.
3. Support disposer with one hand and insert end of wrenchette or screwdriver
into right side of one mounting lug on lower mounting ring (see Figure 3.2).
Lift disposer slightly and remove from mounting by pushing or pulling
wrenchette or screwdriver to left (disposer may be heavy; provide support).
4. Loosen three mounting screws, pry snap ring off with screwdriver, and
remove old mounting assembly (see Figure 3.3). Some mounting assembly removal
requires additional tools.
5. Push old sink flange up through sink hole (see Figure 3.4).

4

6

4.1
5
6.1

6.2 5.1

4 DISASSEMBLE NEW DISPOSER MOUNTING ASSEMBLY
1. Turn mounting assembly over (see Figure 4.1) and loosen three mounting
screws (1) until you can access snap ring (2).
2. Use screwdriver to pry snap ring off of sink flange. Mounting assembly can
now be disassembled.
5 ATTACH UPPER MOUNTING ASSEMBLY TO SINK
Reference Figure 5.1. 1. Place one of two rubber gaskets (2) under sink flange
(1). Ensure sink hole
area is clear of debris and place sink flange/gasket into sink hole. You may
wish to place a weighted object in the sink to hold the sink flange in place.
(Place a towel under object to prevent scratching.) 2. Working from under the
sink, slip second rubber gasket (2), fiber gasket (optional) (3) and metal
backup flange (4) (flat side up) over the sink flange. Holding second rubber
gasket, fiber gasket (optional) and metal backup flange in place, slip
mounting ring (5) over sink flange so it seats against backup flange. 3. With
the rubber gasket, fiber gasket (optional), backup flange, and mounting ring
tight against sink bottom, slide snap ring (7) onto sink flange until it pops
into groove on flange. 4. Tighten three mounting screws (6) up to sink until
mounting assembly is seated tightly and evenly against sink.
IF YOU ARE NOT CONNECTING A DISHWASHER TO DISPOSER, SKIP AHEAD TO INSTRUCTION
7.

6 REMOVAL OF KNOCKOUT PLUG FOR DISHWASHER CONNECTION
In Australia, removal of knockout plug does not apply. It is suggested that
the dishwasher units be connected to IPLEX/ COROMA dishwasher spigot for
maximum efficiency. Wastewater from a dishwasher can be plumbed into the
disposer through the inlet access on the upper part of the disposer. There is
a plug on the inside of the inlet tube on all models. Once removed, the
knockout plug cannot be replaced.
NOTICE
PROPERTY DAMAGE If the dishwasher connection is made without removing the
plug, the dishwasher may overflow. (Connections must comply with local
plumbing codes.)
REMOVE KNOCKOUT PLUG 1. Lay disposer on its side and insert slotted
screwdriver into dishwasher inlet
so tip rests on outer edge of knockout plug. 2. Tap end of screwdriver handle
with hammer until molded plug breaks
loose. (See Figure 6.1) 3. Remove loose knockout plug from inside disposer.
(See Figure 6.2)

7
EVOLUTION MODELS, BW5
7.1
66, 56, 46, BW4, BW3, BW2, E75

8

MODEL S/N XXX

XX ­ XX XXXXXX

X

PUSHTORERDESBEUTTTON

8.1

8.2

9
MODEL XX ­ XX S/N XXXXXXXXXX
9.1
10

4

4

5

5

6

7 6

8 6

7.2

7 ATTACH DISCHARGE TUBE TO WASTE DRAIN PIPE
NOTICE
PROPERTY DAMAGE · All Evolution Models and Model BW5 must be connected to the
supplied
tailpipe with the supplied spring type hose clamp (See Figure 7.1). In
Australia it is required to use the supplied straight discharge tube with
supplied spring type hose clamp. (See Figure 7.2) Failure to use the supplied
tubes and spring type hose clamp will void the guarantee and possibly cause
premature failure of the Anti-Vibration Tailpipe MountTM. · Do not use
plumber’s putty on any other disposer connection. Do not use thread sealants
or pipe dope. These may harm disposer and cause property damage. · Regularly
inspect disposer and plumbing fittings for water leaks, as water leaks can
cause property damage. Manufacturer cannot be held responsible for property
damage as a result of water leaks. · To properly drain and prevent standing
water in the disposer when utilizing a straight pipe discharge tube, the tube
connection opposite the disposer outlet must be lower ­ not higher ­ than the
disposer outlet.

DISCHARGE TUBE INSTALLATION (Evolution Models and Model BW5) Place discharge
tube (2 or 3) into Anti-Vibration Tailpipe MountTM. Secure with spring type
hose clamp (1). (See Figure 7.1)
DISCHARGE TUBE INSTALLATION (MODELS 66, 56, 46, BW4, BW3, BW2, E75) 1. Place
metal flange (5) over discharge tube (7 or 8). Insert rubber gasket (4) with
gasket lip facing the metal flange into discharge tube. (See Figure 7.2)
2. Secure metal flange and discharge tube to disposer with two 13 mm bolts
6).

8.3
8.4
8 CONNECT DISPOSER TO MOUNTING ASSEMBLY
PERSONAL INJURY To avoid personal injury, do not position your head or body
under disposer; the unit could fall during installation.
Clear any objects from inside the disposer grind chamber before mounting the
disposer to the sink. 1. This product must be installed so that the red motor
reset button, power
supply cord plug and earth ground receptacle are readily accessible. Keep this
space clear of all objects. 2. Prior to connecting disposer to mounting
assembly, detach the perforated portion of the specification label found at
the base of the disposer, and set aside for Instruction 9. (See Figure 8.1) 3.
Lift disposer, insert top end (mounting gasket) into mounting assembly.
Position disposer with three mounting tabs (1) aligned in position to slide
over mounting tracks (2) (see Figure 8.2). 4. Turn lower mounting ring to
right (with wrenchette or adjustable pliers) until mounting tabs lock over
ridges (3) on mounting ring tracks (see Figure 8.3).
NOTICE Make sure all three mounting tabs are locked over ridges.
Disposer will now hang by itself. 5. For Evolution Models, Models 66, BW5, BW4
and E75 Insert sound baffle
into sink opening, with flat side upward. (See Figure 8.4) 6. Rotate disposer
so that discharge tube is aligned with drain trap. (To
prevent leaks, do not pull or bend discharge tube to drain trap.) If discharge
tube is too short, you can purchase an extension from hardware store.
(Disposer must remain in vertical position to prevent vibration.) 7. Place
nut, then ferrule on discharge tube and tighten on drain trap. (If you have a
double sink, use separate drain traps for both sides of sink.) 8. Ensure lower
mounting ring is still securely locked over ridges on mounting flange. (See
Figure 8.3)

10.1
10.2
9 ATTACH SPECIFICATION LABEL
This specification label contains important information the owner will need to
know in the event service is required. Place the portion of the specification
label removed in Step 8.1 somewhere easily visible to the user.
IF YOU ARE NOT CONNECTING A DISHWASHER TO DISPOSER, SKIP AHEAD TO INSTRUCTION
11.
10 DISHWASHER ATTACHMENT AND OVERFLOW CONNECTION In Australia, dishwasher
attachment and over flow connection does not apply. It is suggested that the
dishwasher units be connected to IPLEX/ COROMA dishwasher spigot for maximum
efficiency. If you have a sink overflow, it should be connected to the
overflow inlet on the tailpipe (see Figure 10.1). To connect the overflow,
remove the plug in the tailpipe by unscrewing the overflow connector cap (see
Figure 10.2). FOR NEW ZEALAND ONLY Connect the hose from the dishwasher to the
disposer inlet using a dishwasher drain connection kit with a hose clamp (not
provided). NOTE: The straight discharge tube for use in Australia does not
have an overflow connection tube.

11

12

11.1

11.2

11.3

12.1

12.2

12.3

MODEL XX ­ XX S/N XXXXXXXXXX
PUSH RED BUTTON TO RESET

MODEL XX ­ XX S/N XXXXXXXXXX
PUSH RED BUTTON TO RESET

Models 46/56/66/BW2/ BW3/BW4/E75

Evolution® 100/150
Model BW5

Evolution® 200/250

Everyday food waste

Vegetable peels

Plant fibre, animal skins

Avoid grinding

X

large amounts at

once

12.4

12.5

12.6

Bones

Avoid grinding large bones

33 mm

11.4

11.5

11 CONNECT DISPOSER TO ELECTRICAL SUPPLY
ELECTRICAL SHOCK · If three-prong, earth (grounded) plug is used, plug must be
inserted
into three-hole, earth (grounded) receptacle. · Do not modify plug provided
with unit (if applicable). · Improper connection of equipment earth (grounded)
conductor can
result in electric shock. · All wiring must comply with local electrical
codes. · Do not attach earth wire (ground wire) to gas supply pipe. · Do not
reconnect electrical current at main service panel until proper
earth (grounded) outlets are installed by a qualified electrician. · If the
supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified-persons in order to
avoid a hazard.
PERSONAL INJURY Install and route tubing for air switch as such to reliably
reduce likelihood of mechanical damage or stress, allowing proper on/off
operation of the air switch.
NOTE: You must have access to a separate circuit wall socket that is earth
(grounded) to main service panel. Any additional socket should be fitted by a
qualified electrician and properly earthed (grounded). The disposer is fitted
with a power supply cord plug.
ON/OFF CONTROL There are two types of controls for continuous-feed disposers:
a doublepole switch and an air switch (built in for Evolution Models, Model
66, Model 56, Model BW5, Model BW4, Model BW3 and Model E75; available as an
accessory on all other models). DOUBLE POLE SWITCH (1): If a wall switch (not
supplied) is required for your installation, it must have on/off markings and
be installed by a qualified tradeperson. It should be located in a convenient
position above the work surface with a minimum of 3 mm contact separation
between each pole. In New Zealand, please refer to AS/NZS 3000:2007 for
electrical installation. Connect to a 20 amp earth (grounded) wall socket (2)
using a 20 amp cable. (See Figure 11.1) See instructions for DISABLING THE AIR
SWITCH.

AIR SWITCH (Evolution Models, MODELS 66, 56, BW5, BW4, BW3 and E75) The
Evolution Models, Model 66, Model 56, Model BW5, Model BW4, Model BW3 and
Model E75 disposers include a built-in air switch. An air switch activates/
turns off the unit by sending a pulse of air to the control box.
AIR SWITCH INSTALLATION If you wish to change the button finish (optional),
simply pry off the existing button and snap the other button finish onto the
bellows. (See Figure 11.2)
1. Drill a 33 mm wide hole into the kitchen work top, or the corner of the
sink unit, at the most convenient point for use. Some sink units may already
have a suitable hole in them which can be exposed by removing the cap.
2. Remove the nut from the push button bellows, while keeping the stainless
steel washer and rubber gasket in place. Push one end of the PVC tubing onto
the spout of the push button bellows, feed the other end of the tube through
the hole in the work top and through the nut underneath the work top. (See
Figure 11.3)
3. Fit the push button bellows in the hole and then thread the nut underneath
the work top until it is hand tight. Do not use a wrench to tighten the nut.
(See Figure 11.4)
4. Take the other end of the air tube and firmly push it over the spout of
the air switch, which is located on the underside of the waste disposer (See
Figure 11.5).
DISABLING THE AIR SWITCH The air switch can be disabled if wall switch
operation is preferred. The disposer is shipped with the switch in the “off ”
position.
1. Push one end of the PVC tubing provided onto the spout of the push button
bellows. (See Figure 11.3)
2. Take the other end of the air tube and firmly push it over the spout of
the air switch, which is located on the underside of the waste disposer (See
Figure 11.5).
3. Depress the air switch one time until you hear the switch “click.” Remove
and discard the push button bellows and PVC tubing. The disposer may now be
activated by a wall switch.
The disposer installation is complete. Read all operating and safety
instructions in Instruction 12 before operating the disposer.
Lastly, place stopper in sink in close position. Fill sink with water, remove
stopper, turn disposer on and check for leaks.

12 IMPORTANT SAFETY INFORMATION

When using electronic appliances, basic precautions are always to be followed,
including:
· In Australia, product may require approval of the relevant regulator and/or
the sewerage system operator.
· If the air switch or wall switch fails to shut off or turn on disposer,
unplug power cord plug and contact your qualified trade person.
· This product is designed to dispose of normal household food waste;
inserting materials other than food waste into disposer could cause personal
injury and/or property damage. To reduce the risk of injury, do not use the
sink containing the disposer for purposes other than food preparation (such as
baby bathing or washing hair).
· This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the

appliance in a safe way and under stand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
· When attempting to loosen a jam in the food waste disposer, switch off or
unplug the appliance before attempting to free a jammed rotor. Use a self
service wrenchette as described in the Releasing Disposer Jam section.
· Use long-handled tongs or pliers to remove objects from disposer.
· To reduce the risk of injury by materials that are expellable by a waste
disposer, do not operate Evolution or Model BW5 disposers without the sound
baffle in place (see Figure 8.4). Place stopper in sink opening as shown in
Figure 12.2 or 12.4. Do not put the following into a disposer: clam or oyster
shells, caustic drain cleaners or similar products, glass, china, or plastic,
large (whole) bones, metal (such as bottle caps, steel shot, tin cans, or
utensils), hot grease or other hot liquids.

· Replace sound baffle/mounting gasket/ splash baffle when worn to help
prevent entry or ejection of material and water.
· When not using disposer, leave stopper in place to reduce risk of objects
falling into disposer. Make sure disposer power switch is turned off.
· Before pressing reset button, attempting to clear jam, or removing objects
from inside disposer, make sure disposer power switch is turned off.
· Do not insert hands or fingers into disposer.
· FIRE HAZARD: Do not store flammable items such as rags, paper, or aerosol
cans near disposer. Do not store or use gasoline or other flammable vapors and
liquids in vicinity of disposer.
· LEAK HAZARD: Regularly inspect disposer and plumbing fittings for leaks,
which can cause property damage and could result in personal injury.
· Do not dispose of the following in the disposer: paints, solvents, household
cleaners and chemicals, automotive fluids, plastic wrap.

OPERATING INSTRUCTIONS (EVOLUTION MODELS, Model BW5) 1. Remove strainer basket
and plug from
sink opening and run cold water.
2. Turn on wall switch or press air switch (see Figure 12.1) to start
disposer.
3. Slowly insert food waste into disposer and position strainer basket and
plug in upright position (allowing water to run through) to minimize noise and
possible ejection of material while grinding (See Figure 12.2).
4. After grinding is complete, turn disposer off and run water for a few
seconds to flush drain line.
5. Strainer basket and plug also acts as a stopper in the lower position.
(See Figure 12.3)
OPERATING INSTRUCTIONS (MODELS 66, 56, 46, BW4, BW3, BW2, E75)
1. Remove stopper from sink opening and run cold water.
2. Turn on wall switch or press air switch (see Figure 12.1) to start
disposer.
3. Slowly insert food waste into disposer and position stopper to minimize
possible ejection of material while grinding. (See Figure 12.4)

4. After grinding is complete, turn disposer off and run water for a few
seconds to flush drain line.
DO… · First turn on cold water and then turn
on the disposer. Continue running cold water for a few seconds after grinding
is completed to flush the drain line.
· Grind small amounts of hard material such as bones, fruit pits, and ice. A
scouring action is created by the particles inside the grind chamber.
· Grind peelings from citrus fruits to freshen up drain smells.
· Grind food waste with minimum cold water flow of 6 liters per minute.
· Grind common food waste, such as fruits, vegetables, meats, bones, coffee
grounds, etc.
· Switch off or unplug the appliance before attempting to free a jammed
disposer with the wrenchette.
· Maintain the area around the disposer free of any objects to be sure you
have access to the disposer reset button.

DON’T… · DON’T POUR GREASE, OIL OR FAT
DOWN YOUR DISPOSER OR ANY DRAIN. It can build up in pipes and cause drain
blockages. Put grease in a jar or can and dispose in the trash.
· DON’T use hot water when grinding food waste. It is OK to drain hot water
into the disposer between grinding periods.
· DON’T turn off water or disposer until grinding is completed and only sound
of motor and water running is heard.
· DON’T grind fibrous materials like corn husks, artichokes, etc., in any
Models 66, 56, 46, BW4, BW3 or BW2 to avoid possible pipe blockage. Also avoid
grinding animal skins in these models.
· DON’T grind raw chicken or duck feet in any disposer.
· DON’T grind non-food waste of any kind.
· DON’T use this appliance to dispose of hard materials such as glass and
metal.
· DON’T fill disposer with a lot of food waste all at once. Instead, turn the
water and disposer on first and then feed the food waste in gradually.

· DON’T waste food. Nearly a quarter of the food we buy is thrown away
untouched: salad, bread and cakes and fruit head the list. Three tips to stop
waste and save you money: only buy, or cook, the portions you need for the
meal; check the fridge and cupboard for food you haven’t eaten ­ make it your
next snack or freeze it; and make sure you leave that food off your next
shopping list!
CLEANING DISPOSER Over time, grease/food particles may accumulate in the grind
chamber and baffle, causing an unpleasant odor. To clean the disposer: 1. Turn
off disposer and disconnect
power supply.
2. Reach through sink opening and clean underside of splash baffle and inside
upper lip of grind chamber with scouring pad.
3. Place stopper in sink opening and fill sink halfway with warm water.
4. Mix 60 ml baking soda with water. Turn disposer on and remove stopper from
sink at same time to wash away loose particles.

RELEASING DISPOSER JAM If the motor stops while the disposer is operating, the
disposer may be jammed. To release jam: 1. Turn disposer power and water off.
2. Insert one end of the self-service wrenchette into the center hole on the
underside of the disposer (see Figure 12.5). Work the wrenchette back and
forth until it turns one full revolution. Remove wrenchette.
3. Reach into the disposer with tongs and remove object(s). Allow the
disposer motor to cool for 3 – 5 minutes and lightly push red reset button on
the underside of the disposer (see Figure 12.6). (If the motor remains
inoperative, check the service panel for tripped circuit breakers or blown
fuses.)

IN-HOME FULL SERVICE GUARANTEE

Warranty is determined by the unit serial number and the date of installation.
Purchase or installation receipt may be required to verify warranty status.

Evolution 150-3: 7 years Evolution 200-3B: 6 years Evolution 250-3: 8 years
Model 66-3, -10: 4 years Model 46-3, -10: 2 years Evolution 100-3B, -11B: 5
years

Model 56-3, -10, -11: 3 years Model BW5-10: 5 Years Model BW4-10: 4 Years
Model BW3-10: 3 Years Model BW2-10: 2 Years Model E75-3: 5 years

SERVICE
If service is required, contact an InSinkErator Authorized Service Center or
your dealer. Guarantees are void if you remove your disposer after
installation and attempt to repair it, or if the disposer is used for
commercial purposes.

References

• Insinkerator
• Garbage Disposals | Instant Hot Water Dispensers | InSinkErator US
• InSinkErator Australia
• Contact Us

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>