Tc helicon play acoustic инструкция на русском

Подробное описание

Варианты подключения PLAY ACOUSTIC

Картинка с сайта: audio-video.ru

Картинка с сайта: audio-video.ru

Картинка с сайта: audio-video.ru

Картинка с сайта: audio-video.ru

Картинка с сайта: audio-video.ru

Картинка с сайта: audio-video.ru

Картинка с сайта: audio-video.ru

Дополнительно

Картинка с сайта: audio-video.ru

Напольная педаль-процессор для вокала и электрогитары; вокальный гармонайзер; реверберация; эффект эха и задержки; µMod; хард тюнинг; лупер; Amp Emulation; 1 микр. вход XLR; 1 сквозной вход для гитары TRS; 1 лин. вход; 2 выхода XLR; микрофонный предусилитель; фантомное питание; USB; LCD-дисплей; 220 В (сетевой адаптер); 200х156х45 мм; 0.95 кг.

Картинка с сайта: audio-video.ru

Напольная педаль-процессор для вокала/гитары/синтезатора; 6 кнопок с эффектами; гармонайзер; реверберация; эффект эха и задержки; дублирование; µMod; хард тюнинг и коррекция тона; компрессор/EQ; De-Ess; Gate; лупер; 1 микр. вход XLR; 1 сквозной вход для гитары; 2 лин. входа; 2 выхода XLR/TRS; вход/выход S/PDIF; вход/выход MIDI; 1 выход для наушников; микрофонный предусилитель; фантомное питание; USB; LCD-дисплей; 220 В (сетевой адаптер); 350х76х216 мм; 2.3 кг.

Картинка с сайта: manualmachine.com

English Manual

Play Acoustic

Картинка с сайта: manualmachine.com

Important safety instructions 1

Before you begin 4

About this manual 5
Getting support 5
VoiceSupport 5
Please register your Play Acoustic 5

Introduction 6

Diagram legend 7
Diagrams 8

Basics 9

Inputs and outputs 10
Gain settings 12
Switches and operation 14
Control knob and arrow buttons 16
Soft buttons 18

Connection diagrams 20
Mixer setup 21
Play Acoustic back panel inputs
and outputs 21
Stereo (or mono) vocals and guitar 22
Mono vocals and guitar amp 23
Mono vocal and guitar with a
TC-Helicon FX150 24
Mono vocals via FX150 and a guitar amp 25
Guitar and vocals via FX150 and stereo out
to a PA 26
Stereo PA and TC-Helicon
Guitar & Headphone cable 27

Setup button/section 28
Input page (1/7) 29
Output page (2/7) 31
System page (3/7) 32
System page 2 (4/7) 33
Loop page (5/7) 34
Switch-3 page (6/7) 35
Product Info page (7/7) 36

Vocal FX button/section 37
Harmony page (1/7) 39
Harmony Advanced page 40
Double page (2/7) 41
Delay page (3/7) 42
Delay Advanced page 43
Reverb page (4/7) 44
HardTune page (5/7) 45
Transducer page (6/7) 46
Transducer Advanced page 47
µMod page (7/7) 48

Guitar FX button/section 49

Guitar Reverb page (1/7) 51
Guitar µMod page (2/7) 52
BodyRez EQ page (3/7) 53
BodyRez Shelf EQ page (4/7) 54
BodyRez Parametric EQ page (5/7) 54
BodyRez Compressor page (6/7) 54
Guitar Anti-Feedback page (7/7) 56
Notch Filter section 56
Simple steps for feedback reduction 56

Mix button/section 57
Mix page (1/2) 58
Mix page (2/2) 59

The Looper 60
What is looping? 61
Using the Play Acoustic looper 61
Looping tips 62
Using a Switch-3 for looping 63

Troubleshooting 64
General troubleshooting 65

Appendix 66
TC-Helicon scales reference chart 67

Links 68

Technical specifications 70

Product Play Acoustic

Product (firmware) version 1.0

Document Reference manual

Document version / date 2014 — 07-16

Play Acoustic – Reference manual (2014-07-16) a

Картинка с сайта: manualmachine.com

Important safety instructions

Important safety instructions

Play Acoustic – Reference manual (2014-07-16) 1

Картинка с сайта: manualmachine.com

Important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. In­stall in accordance with the manufacturer’s
instructions.

8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that pro­duce heat.

9. Do not defeat the safety purpose of the po­larized or grounding-type plug. A polarized
plug has two blades with one wider than
the other. A grounding-type plug has two
blades and a third grounding prong. The
wide blade or the third prong is provided for
your safety. If the provided plug does not fit
into your outlet, consult an electrician for
replacement of the obsolete outlet.

10. Protect the power cord from being walked
on or pinched, particularly at plugs, con­venience receptacles, and the point where
they exit from the apparatus.

11. Only use attachments/accessories speci­fied by the manufacturer.

12. Use only with a cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the ap­paratus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.

14. Refer all servicing to qualified service per­sonnel. Servicing is required when the ap­paratus has been damaged in any way,
such as power-supply cord or plug is dam­aged, liquid has been spilled or objects
have fallen into the apparatus, the appara­tus has been exposed to rain or moisture,
does not operate normally, or has been
dropped.

Caution

You are cautioned that any change or modifi­cations not expressly approved in this manual
could void your authority to operate this equip­ment.

Service

►

All service must be performed by qualified
personnel.

►

There are no user-serviceable parts inside.

Warning

►

To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture
and objects filled with liquids, such as vases,
should not be placed on this apparatus.

►

This apparatus must be earthed.

►

Use a three wire grounding type line cord like
the one supplied with the product.

►

Be advised that different operating voltages
require the use of different types of line cord
and attachment plugs.

►

Check the voltage in your area and use the
correct type.

Voltage Line plug according to standard

110 to 125V UL817 and CSA C22.2 no42.
220 to 230V CEE7 page VII, SR section 107-

2-D1 / IEC83 page C4.

►

This equipment should be installed near the
socket outlet and disconnection of the device
should be easily accessible.

►

To completely disconnect from AC mains, dis­connect the power supply cord from the AC
receptacle.

►

The mains plug of the power supply shall re­main readily operable.

►

Do not install this device in a confined space.

►

For use at an altitude of 2000m or lower.

►

Do not open the unit – risk of electric shock
inside.

Play Acoustic – Reference manual (2014-07-16) 2

Картинка с сайта: manualmachine.com

Important safety instructions

EMC / EMI

Electromagnetic compatibility /
Electromagnetic interference

This equipment has been tested and found to
comply with the limits for a Class B digital de­vice, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable
protection against harmful interference in resi­dential installations. This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.

If this equipment does cause harmful interfer­ence to radio or television reception, which can
be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:

For customers in Canada

This Class B digital apparatus complies with Ca­nadian ICES-003.

Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.

Explanation of graphic symbols

The lightning bolt triangle is used to

alert the user to the presence of unin­sulated “dangerous voltages” within
the unit’s chassis that may be of suffi­cient magnitude to constitute a risk of
electric shock to humans.

The exclamation point triangle is used

to alert the user to presence of impor­tant operating and service instructions
in the literature accompanying the
product.

►

Reorient or relocate the receiving antenna.

►

Increase the separation between the equip­ment and receiver.

►

Connect the equipment into an outlet on a cir­cuit different from that to which the receiver is
connected.

►

Consult the dealer or an experienced ra­dio / TV technician for help.

Play Acoustic – Reference manual (2014-07-16) 3

Картинка с сайта: manualmachine.com

Before you begin

Before you begin

Play Acoustic – Reference manual (2014-07-16) 4

Картинка с сайта: manualmachine.com

Before you begin

About this manual

This manual will help you understand and oper­ate your Play Acoustic.

You can download the most current version of
this reference manual from
tc-helicon.com/products/play-acoustic/support/

To get the most from this reference manual,
please read it from start to finish, or you may
miss important information.

Getting support

If you still have questions after reading this ref­erence manual, please read the FAQs, visit the
user forums and get in touch with support at:
support.tc-helicon.com/

VoiceSupport

VoiceSupport is the application that allows you
to fully unlock the potential of your TC-Helicon
product and stay in touch with the latest news,
tips and tricks.

VoiceSupport key features include:

►

Professionally authored preset libraries

►

Direct access to product manuals

►

Update messaging – helping you stay up to
date with the latest software

►

Drag & drop preset management

►

Customizable content about your products

►

VoiceCouncil feeds for the latest advice for
singers

►

Firmware upgrading

►

Account management

►

Access to support

Please register your Play Acoustic

To register your Play Acoustic using the Voice­Support software, launch VoiceSupport and
click on the ACCOUNT button.

Please note that registration of your product is

not required to use VoiceSupport, download

presets, update firmware or contact support.

You can download VoiceSupport for Microsoft
Windows and Mac OS X from
tc-helicon.com/products/voicesupport/

Play Acoustic – Reference manual (2014-07-16) 5

Картинка с сайта: manualmachine.com

Introduction

Introduction

Play Acoustic – Reference manual (2014-07-16) 6

Картинка с сайта: manualmachine.com

Introduction

Welcome to the Play Acoustic manual!

First, thank you so much for purchasing Play
Acoustic. We at TC-Helicon are confident that
your vocal and acoustic guitar performances
will be positively impacted with this great effects
processor.

As you discovered in the Quick Start Guide (the
short manual that came in the box), Play Acous­tic is easy to use at the top level, but there is
more under the hood of this compact device
than you might think. We recommend you treat
your Play Acoustic like any other new instrument
and dedicate some time to learning how to use it.

Yes, that means RTFM!

Read the… full manual.

And if you ever find yourself without this manual:
On the bottom of your Play Acoustic , you will
find a “cheat sheet” explaining the most impor­tant functions.

Diagram legend

The following icons are used in the diagrams in
this manual.

Microphone

Acoustic Guitar

Monitor Mix

P.A.

Guitar amp

XLR cables

¼“ / 6.5mm TRS (Tip / Ring / Sleeve )
and TS (Tip / Sleeve) guitar cables

⅛” / 3.5mm cable

Mixing Board

Play Acoustic – Reference manual (2014-07-16) 7

Картинка с сайта: manualmachine.com

Introduction

Diagrams

On the following pages, you will see some con­nection diagrams. We have set things up to give
you clear and concise representations of what
goes where.

There are a few things we would like you to keep
in mind as you look at the diagrams:

1. Inputs to Play Acoustic will be to the left of the
back panel image.

2. Outputs from Play Acoustic will be to the right
of the back panel image.

3. There are two boxes on the bottom of each
diagram.

►

The Play Acoustic box shows “what you
hear” from your Play Acoustic headphone
output.

►

The P.A. box shows “what you hear” from
the P.A. speakers.

4. We don’t account for other inputs/instruments
when showing “what you hear” from the P.A.,
so you won’t see pictures of drums etc.

5. In a lot of cases, “what you hear” will be the
same for both Play Acoustic headphone out­put and P.A. – but it can also be different.

PLAY ACOUSTIC

5 5

3

4

Play Acoustic – Reference manual (2014-07-16) 8

Картинка с сайта: manualmachine.com

Basics

Basics

Play Acoustic – Reference manual (2014-07-16) 9

Картинка с сайта: manualmachine.com

Basics

Play Acoustic – rear panel

GUITAR IN connector

Connect your guitar to this input.

via the Voice (L) connector, and a mono guitar
signal is sent via the Guitar DI (R) jack. This con­figuration can be changed in the Setup/Output
menu.

Inputs and outputs

Connectors are described from right to left. For
setup examples, see “Connection diagrams”.

MIC connector

This is where the magic happens!

Plug your dynamic, condenser, MP-75, or e835
fx microphone in here. Remember to set the mi­crophone type and level correctly, as described
in the Play Acoustic Quick Start Guide.

Play Acoustic – Reference manual (2014-07-16) 10

AUX connector

Use a 1/8” cable to connect any music source
you want to use to your Play Acoustic (especially
that 8-Track from your 1974 Comet). When an in­put is detected here and no guitar is plugged in,
Play Acoustic will use the music signal to figure
out key and scale information.

GUITAR DI (R) and VOICE
(L) output connectors

These are the main output connectors of your
Play Acoustic. By default, mono vocals are sent

GND switch

This is a ground lift switch. If you experience hum
while using Play Acoustic, try pressing the GND
switch to reduce or remove the hum.

Headphones connector

Connect your headphones to the Phones con­necto r.

Картинка с сайта: manualmachine.com

Basics

PEDAL connector

Use a TRS cable to connect a Switch-3 (optional)
to the PEDAL connector. If you use the Switch-3,
you have direct access to looping and other ef­fect control. See the Switch-3 menu section for
details on assigning controls to each Switch-3
button.

USB connector

Connect to your computer with the included ca­ble. Use the VoiceSupport software to manage
presets and update the product’s internal soft­ware (firmware).

You can download VoiceSupport here:
tc-helicon.com/products/voicesupport/

Stereo audio input and output via USB is also
supported at 16bit resolution with 44.1or 48kHz
sample rate.

Incoming USB audio signals are NOT passed to
the USB output, allowing you to sing/play along
with tracks from your DAW while recording back
“just the vocals and guitar”.

Power socket

Connect the included power supply. Your Play
Acoustic will power up immediately. Always use

a TC-Helicon power supply (12 V, 400 mA).

Using any other power supply may damage the
unit and will void your warranty.

Play Acoustic – Reference manual (2014-07-16) 11

Картинка с сайта: manualmachine.com

Basics

Gain settings

How the Input LED
Level Meter Works

The LED on the top of your Play Acoustic is used
for both vocal and guitar level metering.

When setting the level for your microphone
or guitar, make sure that you sing or play
separately. If you are setting your vocal level,

don’t play your guitar – and vice versa.

The meter will show a combined level for both
guitar and vocals when you sing and play.

If you see the LED light red – indicating clip­ping –, it is helpful to play/sing individually to see
which input may be getting too much level.

Keep in mind that the combined level of two
inputs can clip, even when the individual in­puts do not. If this happens for you, it’s best to

simply turn down each input slightly until the LED
no longer lights red when you sing and play si­multaneously.

Setting Microphone Gain

Once you have connected your microphone and
selected the microphone type (Dynamic, Con­denser, MP-75, e835 FX), use the Mic Gain knob
on the side of your Play Acoustic to set the input
level for your microphone.

As you increase the level, pay close attention to
the LED on top of Play Acoustic. You want the

input to light the LED green. It’s OK if the LED
sometimes lights yellow – but it should never
turn red. If it does turn red, reduce the level. Red
means that a) the input is overloading and b)
you’ve got powerful lungs!

Setting the guitar level

The control for your guitar input is on Page 1
of the Setup menu. You can access the Setup
menu by pressing the SETUP button and then
use the < or > buttons to move to Page 1. Press
the “soft” button next to the “Guitar IN” box and
use the Control knob to adjust your level.

Reading the LCD Display

The Play Acoustic display

The LCD display of your Play Acoustic displays
the following information:

Preset Name

The name of the currently selected preset. In the
screen shot above, it is “High Harmony“. The
Presets concept is explained in “What are pre­sets?”.

Preset Number

The unique preset number – i.e., the number of
the slot where the preset is stored. In the screen
shot above, it is 1.

“FAV” indicator

The “FAV” indicator is shown in the upper right
corner of the display if the current preset has
been tagged as a Favorite.

“NP” indicator

The “NP” indicator is shown in the lower right
corner of the display when chord information
changes have been detected by Play Acoustic.

You may see the “NP” indicator switch on and off
somewhat erratically as it processes incoming
musical information. This is normal.

What is NaturalPlay?

NaturalPlay is the voodoo we do inside Play
Acoustic to figure out which key your music is in.
If you plug your guitar into the GUITAR IN con­nector, NaturalPlay will look there first for key/
scale info. Next, it will look at the Aux input and
listen to the RoomSense microphones.

Once Play Acoustic “hears” key/scale informa­tion from one of these inputs, it will set the key/

Play Acoustic – Reference manual (2014-07-16) 12

Картинка с сайта: manualmachine.com

Basics

scale on the fly. “NP” is only shown when a
change in key/scale is detected – so don’t panic
if you don’t see it all the time.

“LOOP” indicator

The “LOOP” indicator is shown in the lower right
corner of the display when a loop is running, but
you are currently not on the Loop mode screen.

GB (Guitar Boost) indicator

The GB (“Guitar Boost”) indicator is shown in the
lower left corner of the display when guitar boost
is active.

Genre indicator

If you have set the Genre selector to any other
value than “All”, the currently selected genre is
shown in the upper left corner of the display. In
the screen shot above, it is “Harmony“.

Play Acoustic – Reference manual (2014-07-16) 13

Картинка с сайта: manualmachine.com

Basics

Switches and operation

The three Play Acoustic footswitches

DOWN and UP footswitches

Form here on, we will refer…

►

to the footswitch with the down-pointing tri­angle as the DOWN footswitch and

►

to the footswitch with the up-pointing triangle
as the UP footswitch.

The DOWN and UP footswitches allow you to
navigate through presets.

►

Press a footswitch once to switch to the previ­ous or next preset slot.

►

Press and hold a footswitch to quickly move
through presets.

HIT/ Hold for TALK footswitch

During normal operation, this footswitch acts as
a HIT button. What does this mean?

When you activate HIT by tapping the footswitch,
a new effect (or several effects) will be added
to the current sound. This feature is perfect for
spicing up a section of a song with a particular
effect, e.g. Harmony.

TALK mode

When you press and hold the HIT/ Hold for TALK
footswitch, Play Acoustic enters TALK mode.

In TALK mode, all vocal effects are bypassed,
and the microphone input is passed directly to
the output.

output is muted to allow tuning, but the dry voice
is still passed to the output, allowing you to tune
your instrument and still entertain the crowd with
witty banter.

Activating Loop mode

To enter Loop mode, press and hold the DOWN
and UP footswitches simultaneously.

For more information on the Looper, see “The
Looper”.

Loop mode screen

In Loop mode, the DOWN footswitch controls
the following functions:

►

PL AY

►

REC (Record)

►

Overdub

Holding the DOWN footswitch will undo your
most recently recorded Overdub.

TALK/Tuner mode

If you have a guitar plugged into the GUITAR IN,
you will enter TALK/Tuner mode, activating the
guitar tuner built into Play Acoustic. The guitar

Play Acoustic – Reference manual (2014-07-16) 14

In Loop mode, the UP footswitch controls the
following functions:

►

STOP

►

ERA (HOLD to erase)

Картинка с сайта: manualmachine.com

Basics

To exit Loop mode, tap the HIT footswitch.

You may exit Loop mode while a loop is still play­ing. That means you can choose a new vocal
sound – and then re-enter Loop mode to add a
new overdub to the loop.

Loop Undo/Redo

To undo a loop overdub, press and hold the
DOWN footswitch.

To restore the overdub (Redo), press and hold
the DOWN footswitch again. Restoring a loop
overdub this way is only possible if you have not
recorded another overdub after using Undo.

Looping with a Switch-3

If you connect a TC-Helicon Switch-3 (optional)
to the PEDAL connector of your Play Acoustic,
you can use it to control all Loop features.

The benefit of using a Switch-3 is the addition of
the dedicated Undo button.

When a Switch-3 is connected, Play Acoustic’s
UP and DOWN footswitches are assigned to Set
Key/Scale.

where pressing the DOWN and UP footswitches
simultaneously will allow you to set key/scale.
You can set this mode on System page 5 under
“UP/DN Function”.

When you have activated this alternative mode,
pressing the UP and DOWN footswitches simul­taneously will allow you to set Key and Scale us­ing these two footswitches.

If you don’t know which Key and Scale a particu­lar song is in, try using the last chord of the song
for the Key and Major 2 for the Scale. It’s often
correct, especially in popular music.

For more information, see “TC-Helicon scales
reference chart”. You can also find this chart on
the TC-Helicon website:
support.tc-helicon.com/entries/
21051886-scale-chart-for-TC-helicon-products/

To use your newly selected Key and Scale, sim­ply press EXIT.

To save the current preset with your chosen Key
and Scale, press STORE twice. Storing presets
is covered in more detail later in this manual.

Tap tempo

To access Tap Tempo, press and hold the UP
and HIT footswitches simultaneously.

Tap tempo screen

Once you see the current tempo displayed on
the LCD screen, tap the HIT button in time with
your music.

When you are finished, stop tapping, and the
screen will “time out” back to the preset screen.

For more information, see “Switch-3 page (6/7)”.

Using DOWN and UP for
setting key and scale

Activating Loop mode by pressing the DOWN
and UP footswitches simultaneously is the de­fault mode. There is also an alternative mode

Play Acoustic – Reference manual (2014-07-16) 15

Картинка с сайта: manualmachine.com

Basics

Control knob and arrow buttons

BACK, STORE, arrow buttons and the control knob

Use the control knob to scroll through presets
and to move through various settings in the Edit,
System or other menus.

The arrow buttons act similarly, allowing you
to move through presets, effect/setup pages,
styles, Genres etc.

Quick Tip: You can press and hold the arrow
buttons to “jump” to the first or last page in a
menu. For example, in the Vocal FX menu, you
can move from Harmony (page 1) to Transducer
(page 7) directly by pressing and holding the >
button.

STORE button

What are presets?

To use Play Acoustic effectively, you need to un­derstand the concept of Presets.

Essentially, a Preset is a record of all the settings
for a group of effects that you can recall quickly
and easily.

The Preset concept is extremely flexible. A Pre­set can be general purpose – like a simple Re­verb or Harmony sound. But a Preset can also
represent a specific song or portion of a song via
multiple effects and settings.

icons on the desktop, program behaviors and
much more. When each user logs in, the com­puter recalls all of their custom settings.

Depending on how you like you to work with ef­fects, you may find that you like to use a few gen­eral purpose Presets. Or you might be the kind
of guy or girl who likes to spend a bit more time
in advance of the performance to create Presets
for all sorts of things.

Once you have fine-tuned all settings in the Vo­cal section, you should store them as a Preset,
so you can later recall them.

Keep in mind that you never have to save Guitar
effects settings. They are global and retain their
values across all of your vocal presets.

Storing presets

When you have made a change to a preset, sim­ply press the STORE button.

Pressing the STORE button once will bring up
the name/location display, allowing you to re­name and/or relocate the preset.

Pressing the STORE button again will save the
preset, along with its new name or location.

BACK button

Press the BACK button to exit the current screen
or mode.

Play Acoustic – Reference manual (2014-07-16) 16

A good modern analogy for a Preset is a user ac­count on a computer. Even though each user has
access to the same hardware (CPU, RAM etc.)
each user can change their desktop wallpaper,

Картинка с сайта: manualmachine.com

Basics

Changing preset names

To change the name of a preset, press the
STORE button once, then press the left blue soft
button and use the control knob to modify the
letters/numbers. Press the STORE button again
to complete the process.

Storing a preset to another location

To save the current preset to a different preset
slot (location), press the store button once, then
press the right Blue soft Button and use the
control knob to select the destination number
for the preset. Press store again to complete the
process.

If you change your mind and don’t want to save
the changes, simply press BACK.

Play Acoustic – Reference manual (2014-07-16) 17

Картинка с сайта: manualmachine.com

Basics

Soft buttons

Soft buttons

There are six “soft” buttons on the Play Acoustic
– three on each side of the LC display.

Each button is context-specific – meaning that
when its function is available, you’ll see it lit up
with a WHITE or BLUE LED.

When there is no function available, the button
will not be lit.

►

In white LED mode, the text on the button re­fers to its action.

►

In blue LED mode, the button will select the
segment of the LCD screen that is directly be­side that button.

Not every menu uses all six buttons.

Vocal FX button

Press the Vocal FX button to open the Vocal FX
menu, which controls the settings of the vocal
effects. This button is described in its own chap­ter: “Vocal FX button/section”.

Guitar FX button

Press the Guitar FX button to open the Guitar FX
menu, which controls the settings of the guitar
effects. This button is described in its own chap­ter: “Guitar FX button/section”

Mix button

Press the Mix button to open the Mix menu,
which allows you to adjust the levels of the sig­nals. This button is described in its own chapter:
“Mix button/section”

Favorite button

You can tag a preset as a “Favorite”. This allows
you to e.g. mark all presets you want to use in
a show and filter out all others. This means that
you can use Favorites to create a set list or sim­ply group all the presets you like, regardless of
their Genre.

►

To add the current preset to your Favorites,
press the FAVORITE button. “FAV” will be
shown in the top right corner of the display.

►

To remove the current preset from your Favor­ites, press the FAVORITE button.

►

To only browse your Favorite presets, press
the GENRE button and select FAV as the
Genre. Press the BACK button to return to the
Home screen.

If there are no presets tagged as Favorites, the

FAV option will not appear in the Genre menu.

GENRE button

Genres allow you to filter your presets by cat­egories, such as musical styles and effect types.

Press the GENRE button to open the Genre
menu.

Play Acoustic – Reference manual (2014-07-16) 18

Картинка с сайта: manualmachine.com

Basics

In the Genre menu, use the control knob to
navigate through the available options. Select a
Genre.

Press the BACK button to return to the main win­dow, where you will see only the presets con­tained within the Genre that you have selected.

Presets can be associated with multiple genres.

Setup button

Press the SETUP button to open the Setup
menu, which controls the general functions of
the device. This button is described in its own
chapter: “Setup button/section”

Play Acoustic – Reference manual (2014-07-16) 19

Картинка с сайта: manualmachine.com

Connection diagrams

Connection diagrams

Play Acoustic – Reference manual (2014-07-16) 20

Картинка с сайта: manualmachine.com

Connection diagrams

The following connection diagrams show you
some common ways to hook up Play Acoustic.
For basic information about audio inputs and
outputs, see “Inputs and outputs”.

Mixer setup

For connection to your mixer or PA, check out
this Craig’s Corner video:

youtube.com/watch?v=qq0AOtafIjs

It’s very important to follow gain-staging instruc­tions in order to get the best signal to noise ratio
(SNR) from your device and prevent distortion in
the signal chain.

Play Acoustic back panel inputs and outputs

SWITCH-3

Play Acoustic back panel

Play Acoustic – Reference manual (2014-07-16) 21

TC Helicon PLAY ACOUSTIC инструкция на русском языке

На этот товар еще нет инструкций

Наличие товара

Отзывы на TC Helicon PLAY ACOUSTIC