Radiolink rc6gs инструкция на русском

Картинка с сайта: manualspro.net

RC6GS V3
Instruction Manual

RC6GS V3 Channels RC Transmitter

Картинка с сайта: manualspro.net

Картинка с сайта: manualspro.net

SAFETY PRECAUTIONS

• Never operate your model during adverse weather conditions. Poor visibility can cause disorientation and loss of control of your model.
• Never use this product in a crowd and illegal area.
• Always ensure the trim levers at 0 and battery properly charged before connecting the receiver.
• Always check all servos and their connections prior to each run.
• Always be sure about turning off the receiver before the transmitter.

WARNING
This product is not a toy and is NOT suitable for children under the age of
14. Adults should keep the product out of the reach of children and exercise
caution when operating this product in the presence of children.
Water or moisture may enter the transmitter inside through gaps in the antenna
or joystick and cause model instability, even out of control. If running in
the wet weather(such as game) is inevitable, always use plastic bags or
waterproof cloth to cover the transmitter.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:

1. This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Packing list (Please refer to the sales interface for the actual packing
list)

RC6GS V3 Remote Control System

1.1 Transmitter RC6GS V3
1.1.1 Transmitter Overview

Картинка с сайта: manualspro.net

control other channels
TH| Throttle trigger| Default control channel 2 throttle. Customizable to
control other channels
VR| Knob switch| Default control channel 3. Customizable to control channel
3/4/5/6/7
SwA| Momentary switch| Default control channel 4. Customizable to control
channel 3/4/5/6/7
SwB| Three-way switch| Default control channel 5. Customizable to control
channel 3/4/5/6/7
SwC| Three-way switch| Default control channel 6. Customizable to control
channel 3/4/5/6/7
SwD| Momentary switch| Default control channel 7. Customizable to control
channel 3/4/5/6/7
LK-A| Two-way switch| Lock mode of SwA. Customizable to control channel
3/4/5/6/7
LK-B| Momentary switch| Lock mode of SwB. Customizable to control channel
3/4/5/6/7
LK-C| Momentary switch| Lock mode of SwC. Customizable to control channel
3/4/5/6/7
LK-D| Two-way switch| Lock mode of SwD. Customizable to control channel
3/4/5/6/7

Note:

1. CH in the transmitter stands for Channel.
2. Momentary switch: The servo value will reach the maximum (or the minimum) when pressing the button (the switched is in a certain position), and back to the original value when loosen (the switched is in the certain position again).
3. Two-way switch: The servo value will reach the maximum (or the minimum) when pressing the button once, and back to the original value when pressing the button again.
4. Three-way switch: Three different servo values will be switched when the switch is located at three different positions.

1.1.3 Specifications

Band（2400MHz–2483.5MHz）
Battery Box Dimension: 895925mm (3.52.320.98″)| Channel
resolution: 4096 with regular jitter of 0.5us
Adaptable Models: Cars/Boats/Robots| Operating Current: 80-120mA
Operating Voltage: 4.8-16.8V, 6pcs of AA batteries or 2S-4S LiPo battery|
Low Voltage Alarm: Support

Low RSSI Alarm: Support
Simulator Function: Support
Model Battery Voltage Telemetry: Maximum 8S (33.6V) model battery voltage
telemetry
Compatible Receiver: R7FG(Standard)/R8FG/R8EF/R8F/R6FG/R6F/R4FGM/R4F
FPV Head Track Function: Support
CRSF Protocol: Support

1.1.4 Basic Operations

Картинка с сайта: manualspro.net

Display on LCD Screen

Картинка с сайта: manualspro.net

1.2 Receiver R7FG(Standard Pack)
1.2.1 R7FG Overview
RC6GS V3 comes with an R7FG, 2.4GHz 7 channels receiver, splash-proof, gyro
integrated and high voltage servo supported.

Картинка с сайта: manualspro.net

1.2.2 Specifications
Size: 352214mm (1.380.870.55″)
Channel: 7 channels
Operating Current: 30mA
Control Distance: 600 meters on the ground
Gyro: With gyro-integrated, customizable gyro sensitivity
Water Splash Proof： IPX4
Weight: 6g (0.21 oz)
Antenna Length: 205mm(8.07″)
Operating Voltage: 3-12V
Signal: PWM&PPM&SBUS
Applicable Model Types: Cars /Boats/Robots
Real-time Telemetry: Support. Telemetry of maximum 8S(33.6V) battery
supported.
Compatible transmitter: RC8X/RC6GS V3/RC6GS V2/RC4GS V2/RC6GS (3-position
switch version)/RC4GS (version with P.D AFTER 180101)/T8S/T8FB

1.2.3 Binding
RC6GS V3 and R7FG have already finished binding by default. Turn on the RC6GS
V3 and the R7FG, the signal tower will be displayed on the top of the screen
as in the picture right, which means the transmitter and receiver have
finished binding.
If you purchase a new R7FG receiver separately, you need to bind the receiver
to the transmitter. Each receiver has an individual ID code. When the binding
is done, the ID code will be stored in the transmitter and there’s no need to
rebind.

Binding Steps:

1. Put the transmitter and the receiver close to each other (about 50 centimeters) and power both on.
2. Switch on the transmitter and the LED on R7FG will start flashing slowly.
3. There is a black binding button(ID SET) on the side of receiver. Press the button for more than 1 second and release, the LED will flash quickly, meaning binding process is ongoing.
4. When the LED stops flashing and is always on, binding is complete and there will be a signal tower shown on top of the LCD screen of the transmitter. If not succeed, the LED will keep flashing slowly to notify, repeat the above steps.

Note: Too close distance between the transmitter and receiver may cause a
signal block, which leads to unsuccessful binding or signal loss. After the
binding is successful, if RC6GS V3 and R7FG receiver are too close (for
example, within 60 centimeters), the signal may also be lost because of signal
block. Bring RC6GS V3 transmitter and R7FG receiver farther apart, the signal
loss will disappear automatically.

1.2.4 Precautions for Receiver Usage

1. Please test RSSI(Received Signal Strength Indicator) before operating models. For methods on how to test it, please refer to Chapter 1.2.8.
2. If the antenna of the receiver is damaged, replace it with a new antenna or receiver in time.
3. Keep the two antennas at a 90-degree angle (as shown on the right).
4. Big models may contain metal parts that influence signal emission. In this case, antennas should be positioned at both sides of the model to ensure the best signal status in all circumstances.
5. Antennas should be kept away from metal conductor and carbon fiber at least half inch away and no over bending.
6. Keep antennas away from motor, ESC or other possible interference sources.
7. Sponge or foam material is advised to use to prevent vibration when installing receiver.
8. Receiver contains some electronic components of high-precision. Be careful to avoid strong vibration and high temperature.
9. Special vibration-proof material for R/C like foam or rubber cloth is used to pack to protect receiver. Keeping the receiver in a well sealed plastic bag can avoid humidity and dust, which would possibly make the receiver out of control.

1.2.5 Working Modes
R7FG has a built-in gyroscope, which can output not only PWM signal but also
PPM and SBUS signals. There are four working modes, including ordinary PWM
mode, SBUS mode, Gyro mode, and Gyro + SBUS mode. The channel signal
corresponding to each mode are as follows:

R7FG Working Mode

Working Mode| PWM Mode| SBUS Mode| Gyro mode| Gyro +
SBUS Mode| Note
LED Indicator Color| Green| Blue| Red| Purple(Red+Blue)|
Channel| Telemetry| Telemetry Port of Model Battery Voltage ( + – )
TELEMETRY port is only for 2S-8S battery voltage telemetry. The port cannot be
used to power the receiver.
1| PWM| PWM| PWM| PWM| Steering
2| PWM| PWM| PWM| PWM| Throttle
3| PWM| PWM| PWM| PWM| Auxiliary
4| PWM| PWM| PWM| PWM| Auxiliary
5| PWM| PWM| PWM| PWM| Auxiliary
6/PPM| PWM| PPM| PWM| PPM| Auxiliary
7/S.BUS| PWM| S.BUS| PWM| S.BUS| Auxiliary

Working mode settings

1. Turn on/off the gyro: Short press the binding button 3 times within 2 seconds to switch the gyro on and off, and the color of the LED indicator will switch accordingly.
2. Gyro phase switch: Short press the binding button twice within 2 seconds to switch the gyro phase.
3. Turning on/off the SBUS: short press the binding button once to turn on/off the SBUS, and the color of the LED indicator will switch accordingly. After SBUS signal is enabled, channel 1-5 output PWM; the sixth channel outputs the PPM signal, and the seventh channel outputs the SBUS signal.

1.2.6 Gyro Setup
The gyro function of receiver R7FG for professional car can be enabled and
disabled. When it’s enabled, the turning stability can be maximized during
competition. When there is false position, gyro function keeps the car
straight forward and turn precisely.
A. Gyro Enabled
Factory setting is gyro function OFF by default. Short press the binding
button (ID SET) three times with interval less than 1 second, the RED
indicator flashes three times. Red LED on/off indicates the gyro function is
on/off.
Attention:

1. It’s normal that the servo keeps shaking when connected to the receiver. Because the gyro is helping to correct the steering gear angle of the servo automatically if the gyro function has turned on, you can turn off the gyro function if you do not need this function.
   2. The servo shakes strongly means the gyro is too much sensitive. Please
   turn VR knob to reduce the gyro sensitivity.
   3. If the receiver has been switched to the gyro mode (with LED indicator
   ON), but the gyro does not work when turning the car, please enter the menu
2. GYRO to check if the RATE is close to 0%, and increase the RATE.

B. Gyro Phase
When the gyro forward is enabled, try to turn the model car to check if the
gyro is correcting the wheels. Normally, the wheels should turn right to
correct when the car is turned left while the wheels should turn left to
correct when the car is turned right. If the gyro phase is reversed, short
press the binding button (ID SET) twice with interval less than 1 second. The
RED indicator flashes twice means the gyro phase is switched.
C. Gyro Sensitivity Adjustment
The gyro sensitivity can be adjusted in the BASIC MENU– GYRO in the
transmitter. VR and STD modes are optional. Gyro sensitivity setting is CH3 by
default (factory setting) and can be adjusted by VR knob. If VR knob or
channel 3 is used for other functions,  select STD mode and adjust the gyro
sensitivity by buttons Dec(-) or Inc(+) . Percentage is displayed when
sensitivity is adjusted while the bigger percentage means higher sensitivity.
1.2.7 Telemetry of Model Battery Voltage
Model battery voltage can be returned in real time when R7FG receiver is bound
to RC6GS V3 successfully. It can be set in the menu “19.
ALARM”. For example, if it is 3S lithium battery used in the model car, the
warning value should be set as 11.1V (3.7V*3). The connection is as
follows:

Картинка с сайта: manualspro.net

Note

1. Battery connected to TELEMETRY port is only for 2S-8S (7.4V-33.6V) battery voltage telemetry. The TELEMETRY port cannot be used to power the receiver.
2. R8FG, R7FG and R8F receiver all support telemetry of model battery voltage. Make sure the polarity of the battery is not reversed. Otherwise reverse insertion will cause abnormal voltage display of telemetry.

1.2.8 RSSI Testing
RSSI stands for Received Signal Strength Indicator.
RSSI test method:

1. After successful binding between the receiver and the transmitter, the signal tower in Picture 1 appears on the screen.
   

   Картинка с сайта: manualspro.net

2. Short press the Exit button twice in the home page to enter the return information interface. RSSI is at the top of the interface in Picture 2.
3. Make the receiver antenna and transmitter antenna parallel, and keep a distance of about 60 centimeters from the transmitter(as shown below) to observe the RSSI value. It is normal that RSSI value is within the range of 0 to -30dBm. The closer the value is to 0, the stronger the signal is. If RSSI is not within the range of 0 to -30dBm, the RSSI value is abnormal and there is some problem of signal transmission.
   

   Картинка с сайта: manualspro.net

Abnormal Signal Strength Solution:

1. Check whether the antenna of the receiver or the transmitter is damaged. If it is damaged, the antenna needs to be replaced.
2. If there is no damage of the antenna, you can test the transmitter and receiver for malfunctions by replacing the receiver.

RC6GS V3 Functions

2.1 Servo Value
After powering on RC6GS V3, press the “Exit” button on the main interface to
view the servo value (See Picture 1 and Picture 2 below).
2.2 Language “LANGUAGE”
Both English and Chinese menus are available (See Picture 3 below).
2.3 Model Select “MODEL”
RC6GS V3 can store model memories for 30 models. Use this function to call a
new model. Each model can independently set the parameters of each function
(See Picture 4 below).

Картинка с сайта: manualspro.net

2.4 End Point Adjust “EPA”
Use EPA when performing left and right steering angle adjustments, throttle
high side/brake side operation amount adjustment, and channel 3 servo up
side/down side operation amount adjustment during linkage.
Correct the maximum steering angle and left and right steering angles when
there is a difference in the turning radius due to the characteristics, etc.
of the vehicle.

Картинка с сайта: manualspro.net

Setting item (channel and value range)
CH1 to CH7: 0%~120%
Initial value:100%
End point adjustment
Switch setting: Set a switch or button to switch in different end points.
A. You can set SWA, SWB, SWC, SWD, or the lock modes of these four switch
buttons LK-A, LK-B, LK-C, LK-D.
B. “NULL” means no switch assigned. After setting the end point parameter
of the corresponding channel, the transmitter will always execute the set end
point, and it cannot be switched.
C. UP (up)/DOWN (down)/CNT (central): It indicates the position of the
selected switch. Push/Press the switch to different positions to set different
EPA.

2.5 Steering Exponential “STEXP”
This function is used to change the sensitivity of the steering servo around
the neutral and both ends position. It has no effect on the maximum servo
travel.
RATE: Steering EXP rate
Adjustment range：-100%~0%~+100%
Initial value: 0%
0%~-100%: Sensitivity around neutral position is low, getting higher when
approaching ends.
0%: Sensitivity around the neutral and ends position is equal
0%~+100%: Sensitivity around neutral position is high, getting lower when
approaching ends

2.6 Steering Servo Speed Delay “STSPD”
Quick steering operation will cause momentary under steering, loss of speed,
or spinning. This function is effective in such cases.

Setup item
TURN: turn direction
RETURN: return back to the original direction
Adjustment range
0%~100% (each direction)
At 100%, there is no delay

2.7 Throttle Exponential “THEXP”
This function makes the throttle high side and brake side direction servo
operation quicker or milder. It has no effect on the servo maximum operation
amount. For the high side, selection from among three kinds of curves
(CRV/VTR/EXP) is also possible.
The curve can be divided into: Five dots throttle curve adjustment, Single
point adjustment, Exponential curve adjustment, Braking index curve
adjustment.
MODE:
INH: means the mixing function is disabled. Regardless of whether there
is a set control switch or value under this function, it is not enabled.
ON: means turning the function on. Set the mode to ON, the current mixing
control can take effect.

Картинка с сайта: manualspro.net

Adjustment method for CRV curve (See Picture 1 above)
Mode: ON/INH
RATE: 0%~100%
Adjustment method for VTR curve (See Picture 2 above)
Mode: ON/INH
TG.P: 20-80
RATE: -100~0~+100

Картинка с сайта: manualspro.net

Adjustment method for EXP curve (See Picture 3 above)
MODEL: ON/INH
RATE: -100 ~ 0 ~ +100
Adjustment method for BRK-EXP curve (See Picture 4 above)
RATE: -100 ~ 0 ~ +100
0~-100: flat braking
0: uniform braking
0~+100: sensitive braking

2.8 Throttle Speed Delay “THSPD”
Sudden trigger operation on a slippery road only causes the wheels to spin and
the vehicle cannot accelerate smoothly. Setting the throttle speed function
reduces wasteful battery consumption while at the same time permitting smooth,
enjoyable operation.
Operation
Throttle servo(amp) operation is delayed so that the drive wheels will not
spin even if the throttle trigger is operated more than necessary. This delay
function is not performed when the throttle trigger is returned and at brake
operation.
Speed1 or speed2 can be selected.OFF means shut down the throttle speed
function.

Картинка с сайта: manualspro.net

Adjustment method for SPEED1
MODE: Speed type selection
ALL: Speed adjustment| Adjustment method for SPEED2
MODE: Speed type selection
LOW: Low side range speed adjustment
HIGH: High side range speed adjustment
TGP1: Low and medium speed switching point
—|—
Adjustment range
0~100 (each direction)
At 100, there is no delay| Adjustment range
LOW: 0~100
HIGH: 0~100
At 100, there is no delay
TGP1: 0~100

2.9 A.B.S. Function “A.B.S”
Pulse brake
When the brakes are applied while cornering with a 4 Wheel Drive or other type
of vehicle, under-steer may occur. The generation of under-steer can be
eliminated and corners can be smoothly cleared by using this function.

Operation

• When the brakes are applied, the throttle servo will pulse intermittently. This will have the same effect as pumping the brakes in a full size car.

• The brake return amount, pulse cycle, and brake duty can be adjusted.

• The region over which the ABS is effective can be set ac-cording to the steering operation. (Mixing function)

• MODE
  INH: means the mixing function is disabled. Regardless of whether there is a
  set control switch or value under this function, it is not enabled.
  ON: means turning the function on. Set the mode to ON, the current mixing
  control can take effect.

• ABP(Amount of brake return): Sets the rate at which the servo returns versus trigger operation for brake release. When set to 0, the ABS function is not performed. When set to 50, the servo returns 50% (1/2)of the trigger operation amount and when set to 100, the servo returns to the neutral position.
  Brake return amount (ABP): 0 ~ 50 ~ 100
  Initial value: 50

• Brake return amount (ABP) is influenced by the “EXP” rate on the brake side.

• DLY(Delay): Sets the delay from brake operation to ABS operation.
  “0”: A.B.S. function performed without any delay
  “50”: A.B.S function performed after an approximate 0.7 sec delay
  “100”: A.B.S. function performed after an approximate 1.7 secs delay
  Delay amount (DLY): 0 ~ 100
  Initial value; 0

• CYC(Cycle): The smaller the set value, the faster the pulse cycle.
  Pulse speed adjustment
  Cycle speed (CYC): 0 ~ 30
  Initial value: 5

• TGP(Trigger point): Sets the trigger point at which the ABS function begins to operate at brake operation. The number is the 100 display with the full brake position made 100%.
  Operation point (TGP): 0 ~ 100
  Initial value: 30

• DTY(Cycle duty ratio): Sets the proportion of the time the brakes are applied and the time the brakes are released by pulse operation. The ratio can be set to +3 ~ 0~-3 in 7steps.
  “-3”: Brake application time becomes shortest. (Brakes lock with difficulty)
  “+3”: Brake application time becomes longest (Brakes lock easily)
  (Remark) For low grip set at the – side and for high grip set at the + side.
  Duty ratio (DTY): -3 ~ 0 ~ +3
  Initial value: 0

• STM(Steering mixing): Sets the range within which the A.B.S. function is performed relative to steering wheel operation.
  Steering mixing (STM)
  OFF, N10 ~ N100, E10 ~ E100
  Initial value: OFF
  When steering mixing is set and steering operation enters the set range, “*”
  is displayed in front of the number. When mixing is OFF, the A.B.S function
  can operate over the entire steering range.

Картинка с сайта: manualspro.net

2.10 Throttle Acceleration “ACCEL”
Function which adjusts the movement characteristic from the throttle
neutral position.
The servo will jump to the input position at its maximum possible speed.
Unlike exponential, which adjusts the whole throttle movement into a curve,
throttle acceleration simply “jumps” away from neutral and then leaves the
remaining response linear.

FWRD: Forward side acceleration amount
BRAK: Brake side acceleration amount
(1) Forward side acceleration adjustment
“0%”: No acceleration
“100%”: Maximum acceleration(Approximately1/2of the forward side steering
angle)
Forward acceleration amount(FWRD): 0%~100%
Initial value: 0%
(2) Brake side acceleration adjustment
“0%”: No acceleration
“100%”: Maximum acceleration (Brake side maximum steering angle)
Brake side acceleration amount(BRAK): 0%~100%
Initial value: 0%

2.11 Idle-up “IDLUP”
2.11.1 Idle-up at Engine Start
Use this function to improve the starting characteristics of the engine by
raising the idling speed when starting the engine of a gas powered car.
Idle-Up rate (RATE): -50% ~ -1%, 0%, +1% ~ +50%
Initial value: 0%
“-“: Brake side
“+”: Forward side

2.11.2 Cruise Control “TH-LOCK”
In addition to adjusting the throttle speed when the throttle trigger is in
the neutral position, the Idle up at engine start function can also set the
throttle lock, select the throttle value that needs to be locked, and the
setting range is -100% to +100%. After the throttle is locked, no matter the
current No matter where the throttle trigger is, the throttle output will jump
to the set value.
This function is controlled by the trigger of the SWA, two-way switch, press
to lock, press again to unlock, the control switch defaults to SWA and cannot
be modified.

2.12 Sub-trim “SUBTRIM”
Servo center position adjustment
Use this function to adjust the neutral position of the steering, throttle and
all other channel.
Sub-trim (channel and value range)
CH1-CH7: -100~0~+100
Initial value : 0

2.13 Channel Reverse “REVERSE”
Servo operation reversing
This function reverses the direction of operation of the servos related to
transmitter steering, throttle, channel 3 to channel 7 operation.

2.14 Steering/Throttle Dual Rate “D/R”
The servo travel amount of all channels can be reduced by Dual Rate setting.
Dual rate function is different from EPA, which requires the travel amount on
both sides of the channel to be set separately.
Setting the rate of D/R will affect the left and right travel amount at the
same time. For example, after setting a smaller throttle value, the travel
amount of the model forward and brake will be reduced at the same time, the
setting range is 0-100, the default is 100. The steering left and right servo
travels are adjusted simultaneously.

Switch setting: Set a switch or button to switch in different travel amount of
each channel.
A. You can set SWA, SWB, SWC, SWD, or the lock modes of these four switch
buttons LK-A, LK-B, LK-C, LK-D.
B. “NULL” means no switch assigned. After setting the travel amount of the
corresponding channel, the transmitter will always execute the set value by
default.
C. UP (up)/DOWN (down)/CNT (central): It indicates the position of the
selected switch.
Push/Press the switch to different positions to set different travel
amount.

Картинка с сайта: manualspro.net

2.15 Brake Side Adjustment “ATL”
This function decreases the set value when the braking effect is strong and
increases the set value when the braking effect is weak.
RATE: Brake amount
Brake amount (RATE): 0%~100%
Initial value: 100%

2.16 Programmable Mixes “PMIX01/02”
Programmable mixes between arbitrary channels
These functions allow you to apply mixing between the steering, throttle, CH3,
CH4, CH5, CH6 and CH7. PMIX01 setting is the same with PMIX02.

PMIX:Programmable Mixes
MOD: Mixing mode.
INH: means the mixing function is disabled. Regardless of whether there is a
set control switch or value under this function, it is not enabled.
ON: means turning the function on. Set the mode to ON, the current mixing
control can take effect.
SW: Switch to control the mix function. You can set SWA, SWB, SWC, SWD, or the
lock modes of these four switch buttons LK-A, LK-B, LK-C, LK-D. “NULL” means
no switch assigned. After setting the travel amount of the corresponding
channel, the transmitter will always execute the set value by default.

POS: means the position of the switch used to control this function. UP
(up)/DOWN (down)/CNT (central): It indicates the position of the selected
switch. Push/Press the switch to different positions to set different travel
amount.
LEFT: Mixing rate (Left side)
Mixing amount: -100~0~+100
Select the setting item “LEFT”, “FWRD”, or “UP”(These setup items are
different depend on the master channel. ST: “LEFT”; TH: “FWRD”; CH3-CH7:”UP”)
by pressing “Dec(-)” or “Inc(+)” button.
RIGN: Mixing rate (Right side)
Mixing amount: -100~0~+100
Select the setting item “RGHT”, “BRAK”, or “DOWN”(These setup items are
different depend on the master channel.ST:”RGHT”; TH:”BRAK”;CH3-CH7:”DOWN”) by
pressing “Dec(-)” or “Inc(+)” button.
MST: Master channel
Channel selection (MST): ST, TH, CH3, CH4, CH5, CH6 and CH7.
Initial value: ST
SLV: Slave channel
Channel selection (SLV): ST, TH, CH3, CH4, CH5, CH6 and CH7.
Initial value: ST

2.16.1 Mix Control Setup
The details on how to set the mix control for dual-engine model, please view
the link: https://www.radiolink.com/newsinfo/477940.html
2.17 Auxiliary Channel “AUX-CH”
In addition to the two basic channels of the steering channel (channel 1) and
the throttle channel (channel 2), RC6GS V3 also has five auxiliary channels,
all of which can be customized to assign control switches.
The control switch of the auxiliary channel can be selected as ST(steering),
TH(throttle), VR, SwA, SwB, SwC, SwD, LK-A, LK-B, LK-C, LK-D, NULL.(For more
details of all switches, please refer to Chapter 1.1.4 Switch/Button
Introduction)
Note: When it is set to NULL, the channel will not be controlled by any
switch.

2.18 Model Name “NAME”
RC6GS V3 stores model memories for 30 models. Each model memory can be named
separately according to user’s requirement. Factory default name is MODEL1.

2.19 ALARM(Safety Alarm for Low Voltage and Signal Strength)
Each model can independently set low voltage and RSSI value alarms, but the
alarm functions of RATE and temperature are not yet available. RPM telemetry
functions are still under development. If there are new developments, we will
announce them to the RadioLink official website as soon as
possible.

Картинка с сайта: manualspro.net

The transmitter default alarm voltage is 7.2V, and it can be customized on
2-4S battery .The receiver default alarm voltage is 4.0V, and the vehicle
battery default alarm voltage is 11.1V. The RSSI alarm value is turned off by
default. Users can set it as the RSSI value corresponding to the farthest safe
distance of the actual control. For example, the farthest remote control
distance is 400m, the corresponding RSSI value is -85dBm, then you can set the
RSSI alarm value as -85dBm.
When the voltage of the transmitter, receiver, vehicle battery, and RSSI
signal strength are lower than the set value, there will be a text displayed
on the transmitter screen(See Pictures below) and a “didi” sound dual alarm
prompt to remind you.

Картинка с сайта: manualspro.net

When the above alarm interface appears, press Enter button, the TX, RX, EX, or
RS will appears respectively on the home page for reminding the alarm of the
transmitter, receiver, vehicle battery, and RSSI (See Pictures below). When
the alarm sounds or the warning words of TX, RX, EX, or RSSI appears on the
screen, please stop driving immediately and take the vehicle back, check the
cause of the alarm, and deal with it properly.

Картинка с сайта: manualspro.net

Note:

1. RC6GS V3 can set different low voltage alarm values for each model, but the transmitter low voltage alarm is the same for all models.
2. Due to the different voltage ranges available for lithium battery, nickel metal hydride and nickel cadmium, please set the corresponding voltage value according to the type of battery you use.

2.20 Gyro Sensitivity “GYRO”
This function is available to set gyro sensitivity and VR mixing ON or INH.
When MIX set INH, gyro is disabled while when MIX set ON, you can adjust gyro
sensitivity STD or VR. STD is adjusted on screen and VR is default CH3.
In normal mode (STD), range of sensitivity is 0%-100%.
0% means the minimum gyro sensitivity, or even no gyro function; 100% means
the maximum sensitivity. If the gyro sensitivity is too high, it may cause the
body to vibrate, please adjust the sensitivity according to the vehicle model.

2.21 Fail Safe”F/S”
This function can set the output value of each channel when the receiver loses
control. It is set by servo, throttle, CH3, CH4, CH5, CH6 and CH7.
RANGE: CH1 to CH7: -100~+100
Initial value: 0

2.22 ID SEED
When the transmitter and multiple receivers that have been successfully paired
are powered on at the same time, one of the receivers can be selected to be
controlled through the ID SEED function, while the other receivers are in a
standby state and cannot be controlled.
The transmitter and receiver have the following two control methods:

1. When ID SEED function is turned off (set INH), RC6GS V3 can control multiple devices at the same time.
2. When ID SEED function is turned on (set ON), RC6GS V3 can select a receiver from multiple receivers and control this model, while other receivers are on standby.

Setting method:
Turn on the mode, set the corresponding ID SEED number according to the number
of your car/boat and complete the binding and other settings. After setting
the ID SEED number, the number (such as ID01) will appear on the main
interface of the transmitter.
For example: Bind RC6GS V3 with a truck and a car and turn all them on. First,
use RC6GS V3 to control the car to run to the bucket of the truck, and then
switch the receiver ID on the truck to drag the car back to the destination.

2.23 DSC Port Setting “DSC”
There are 3 modes for DSC function.

1. simulator: Connect to the simulator or TBS Crossfire (See Picture 1 below);
2. 2 axis track: Connect to FPV goggles with head track function (See Picture 2 below).
3. 3 axis track: Connect to FPV goggles with head track function (See Picture 3 below). (RC6GS V3 with firmware V6.7.7 or above supports 3 axis track. If the firmware version is lower than V6.7.7, please update the firmware to use the 3 axis track function)

simulator mode: If you need to connect simulator or TBS Crossfire to RC6GS V3,
please select the mode as: simulator. Insert one end of the standard audio
head of the simulator into the DSC port of RC6GS V3, and follow the steps in
the simulator instruction manual to calibrate and operate the transmitter in
the simulation software. Please refer to the Chapter 3.11 for how to connect
RC6GS V3 to TBS Crossfire:

Картинка с сайта: manualspro.net

2 axis track mode: If you need to connect FPV goggles with 2 axis track
function to RC6GS V3, set the mode to: 2 axis track (or head track in firmware
below V6.7.7). When the DSC mode is selected as 2 axis track or head track,
the DSC port of RC6GS V3 outputs in channel 5 and channel 6 by default.
Connect the roll servo and pitch servo used to control the pan-tilt to the
pins of R7FG receiver in channel 5 and channel 6, and then swing the FPV
goggles up and down or left and right, and the servos of the corresponding
channel will swing accordingly. Please refer to the Chapter 3.12 for how to
setup head track on RC6GS V3.
3 axis track mode: If you need to connect FPV goggles with 3 axis track
function to RC6GS V3, please set the mode to: 3 axis track. When the DSC mode
of RC6GS V3 is selected as 3 axis track, the DSC port outputs in channel 5,
channel 6 and channel 7 by default, which are used to control the pan, tilt
and yaw servos.
Note: If you want to realize the head track function, please make sure
the FPV goggles used support corresponding 2 axis or 3 axis head track
function.

2.24 Timer Setting “TIMER”
TIMER function is mainly used for game timing and daily training.
Mode: Timer mode, you can choose “UP TIMER” or “DOWN TIMER”.
UP TIMER: After triggering the timing function, the timing number will count
upwards.
DOWN TIMER: After triggering the timing function, the timing numbers will
count down.
ALRM(Alarm): The timer starts. When it reaches the set time, the transmitter
starts to alarm. In the countdown 20S, it starts to alarm every 1S. In the
countdown 10S, it starts to alarm twice every 1S. When the alarm time is
reached, the transmitter will give a alarm. If the switch is not toggled now,
the timing will continue. The default alarm time is 8 minutes. The alarm time
can be set according to actual needs START: Select a switch or button used to
trigger the timing function. You can choose SWA, SWB, SWC, SWD, TH (throttle
trigger), and the lock mode of the four switch buttons.
NULL means that the timing function is not enabled. If the switch is set to
SWA, SWB, SWC, SWD or their lock modes, you can select UP (up), CNT (central),
or DOWN (down) for the position of the switch to trigger the timing function.
If the start switch is TH (throttle trigger), you can set the throttle rate to
0%-100%, and the timing function will be triggered when the throttle trigger
is pushed to the set rate.

STOP: It is used to stop the timing function. The setting method is the same
as the above “START” setting. When the number of laps set is greater than 1,
the number of laps will automatically increase by 1 lap each time it stops.
RESET: By toggling the switch set here, all the previously generated timing
values will be cleared.Alarm values and laps are retained. The switch setting
method is the same as the above “START” setting.

Note:

1. When triggering the timing function, please do not put the switch in the stop or reset position, otherwise the timing function cannot be activated.
2. When the switch is not enough, there are 2 ways to reset all timings: a. By setting the “alarm” value, all timings can be reset. b. All timings can be reset by setting the “mode” value.
   LAP: used to set the number of laps required for timing, 1-30 lap numbers can
   be set;
   Display laps: used to display the lap corresponding to the current timing.
   L01-L30 can be selected. For example, when it is L02, the timing below
   correspond to Lap 2. When the number of laps set is greater than 1, the number
   of laps will automatically increase by 1 lap each time it stops.
   Check the timing of each lap: move the cursor to: L01-L30, press the “Enter”
   button, the cursor starts to blink, and then press the “Dec(-)” or “Inc(+)”
   buttons at the bottom of the screen to select the laps to check the timing
   time. The corresponding timing lap and timing will be displayed in the box
   below.

Display: CURRENT, the ON or OFF status of the timing function is only
displayed in the function menu of “Timer”.
HOME PAGE, the ON or OFF status of the timer function is displayed both in the
“Home Page” and “Timer” menu at the same time.

2.25 Factory Reset “RESET”
RESET- Data reset function: All the data for any model memory can be reset to
original factory defaults. Often this function is done to get a “fresh start”
and clear the memory before inputting new model settings.
Note: Resetting the current model memory will permanently erase ALL
programming information for that model. The data cannot be recovered. Do not
reset the model unless you are certain you want to clear-out that memory and
start from scratch.

Tutorials

Please search Radiolink_official on YouTube to access RadioLink official
channel and check all the below video tutorials of RC6GS V3. View the playlist
of RC6GS V3 or search key words on our channel for the function you want.
3.1 Firmware Update of RC6GS V3
3.2 Throttle and Steering Calibration
3.3 Connect RC6GS V3 to Simulator
3.4 THSPD Throttle Delay Function on RC6GS V3
3.5 TIMER Function on RC6GS V3
3.6 Dual Rate Function on RC6GS V3
3.7 EPA Function on RC6GS V3
3.8 Set Different ALARM for 30 Different Models on RC6GS V3
3.9 ID Seed Function on RC6GS V3
3.10 Cruise Control Function on RC6GS V3
3.11 Connect RC6GS V3 to TBS Crossfire
3.12 Head Track Setup on RC6GS V3
3.13 LK-A/LK-D Button Setup on RC6GS V3
3.14 Setup FPV Monitor on RC6GS V3
3.15 TX Low power & Power Supply Options of RC6GS V3

Technical Support Here

Contact RadioLink RL via Facebook Messenger

https://www.radiolink.com/rc6gsv3_video

If the above communication cannot solve your problem, you can also send emails
to our technical support:
after_service@radiolink.com.cn
This content is subject to change. Download the latest version from
https://www.radiolink.com/rc6gsv3_manual

Thank you again for choosing RadioLink product.

Картинка с сайта: manualspro.net

Documents / Resources

|
RadioLink RC6GS V3 Channels RC
Transmitter
[pdf] Instruction Manual
RC6GS, RC6GS V3, RC6GS V3 Channels RC Transmitter, Channels RC Transmitter, RC
Transmitter, Transmitter
—|—

References

• RC6GS V3/RC4GS V3/RC6GS V2/RC4GS V2/RC6GS/RC4GS双引擎混控设置教程-Radiolink 乐迪电子-官方网站
• RC6GS V3 Instruction Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>