1
Contents
Contents
3
4
10
LAN Port LED Status Table …………………………………………………………………………..10
Audio Ports Configuration …………………………………………………………………………….10
11
CPU Socket …………………………………………………………………………………………………12
DIMM Slots………………………………………………………………………………………………….13
DIMM Slots………………………………………………………………………………………………….13
PCI_E1~4: PCIe Expansion Slots ……………………………………………………………………14
JFP1, JFP2: Front Panel Connectors ……………………………………………………………..15
JAUD1: Front Audio Connector ……………………………………………………………………..15
SATA1~6: SATA 6Gb/s Connectors …………………………………………………………………16
M2_1~3: M.2 Slot (Key M) ……………………………………………………………………………..16
ATX_PWR1, CPU_PWR1~2, PCIE_PWR1: Power Connectors ……………………………17
JUSB1~2: USB 2.0 Connectors ………………………………………………………………………18
JUSB3~4: USB 3.2 Gen 1 5Gbps Connector …………………………………………………….18
JUSB1: USB 3.2 Gen 2 Type-C Connector ……………………………………………………….19
JTBT1: Thunderbolt Add-on Card Connector ………………………………………………….19
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors ………………………………..20
JTPM1: TPM Module Connector …………………………………………………………………….20
JCI1: Chassis Intrusion Connector …………………………………………………………………21
JCOM1: Serial Port Connector ………………………………………………………………………21
JDASH1: Tuning controller Connector ……………………………………………………………21
JBAT1: Clear CMOS (Reset BIOS) Jumper ………………………………………………………22
JRAINBOW1~2: Addressable RGB LED connectors …………………………………………22
JRGB1: RGB LED connector ………………………………………………………………………….23
EZ Debug LED ……………………………………………………………………………………………..23
24
Installing Windows® 10 …………………………………………………………………………………24
Installing Drivers …………………………………………………………………………………………24
MSI Center ………………………………………………………………………………………………….24
Thank you for purchasing the MSI®
motherboard. This User Guide gives information about
board layout, component overview, BIOS setup and software
installation.
2Contents
25
BIOS Setup ………………………………………………………………………………………………….26
Entering BIOS Setup …………………………………………………………………………………….26
BIOS User Guide ………………………………………………………………………………………….26
Resetting BIOS …………………………………………………………………………………………….27
Updating BIOS……………………………………………………………………………………………..27
3
Contents
The components included in this package are prone to damage from electrostatic
discharge (ESD). Please adhere to the following instructions to ensure successful
computer assembly.
Ensure that all components are securely connected. Loose connections may cause
the computer to not recognize a component or fail to start.
Hold the motherboard by the edges to avoid touching sensitive components.
It is recommended to wear an electrostatic discharge (ESD) wrist strap when
handling the motherboard to prevent electrostatic damage. If an ESD wrist strap is
not available, discharge yourself of static electricity by touching another metal object
before handling the motherboard.
Store the motherboard in an electrostatic shielding container or on an anti-static
pad whenever the motherboard is not installed.
Before turning on the computer, ensure that there are no loose screws or metal
components on the motherboard or anywhere within the computer case.
Do not boot the computer before installation is completed. This could cause
permanent damage to the components as well as injury to the user.
If you need help during any installation step, please consult a certified computer
technician.
Always turn off the power supply and unplug the power cord from the power outlet
before installing or removing any computer component.
Keep this user guide for future reference.
Keep this motherboard away from humidity.
Make sure that your electrical outlet provides the same voltage as is indicated on
the PSU, before connecting the PSU to the electrical outlet.
Place the power cord such a way that people can not step on it. Do not place
anything over the power cord.
All cautions and warnings on the motherboard should be noted.
If any of the following situations arises, get the motherboard checked by service
personnel:
Liquid has penetrated into the computer.
The motherboard has been exposed to moisture.
The motherboard does not work well or you can not get it work according to
user guide.
The motherboard has been dropped and damaged.
The motherboard has obvious sign of breakage.
Do not leave this motherboard in an environment above 60°C (140°F), it may
damage the motherboard.
4
Supports 10th Gen Intel® Core™ Processors, 11th Gen Intel®
Core™ Processors, Pentium® Gold and Celeron® Processors*
Processor socket LGA1200
* Please go to intel.com for compatibility information
Intel® Z590 chipset
4x DDR4 memory slots, support up to 128GB*
Supports 1R 2133/ 2666/ 2933 MHz for 10th Gen Intel® CPU
(by JEDEC & POR)
Supports 1R 2133/ 2666/ 2933/ 3200 MHz for 11th Gen Intel®
CPU (by JEDEC & POR)
Max overclocking frequency:
1DPC 1R Max speed up to 5333 MHz
1DPC 2R Max speed up to 4700+ MHz
2DPC 1R Max speed up to 4400+ MHz
2DPC 2R Max speed up to 4000+ MHz
Supports Dual-Channel mode
Supports non-ECC, un-buffered memory
Supports Intel® Extreme Memory Profile (XMP)
*Please refer www.msi.com for more information on
compatible memory
2x PCIe x16 slots
Support x16/ x4
PCI_E1 (from CPU)
Supports up to PCIe 4.0 for 11th Gen Intel® CPU
Supports up to PCIe 3.0 for 10th Gen Intel® CPU
PCI_E3 (from Z590 chipset)
Supports up to PCIe 3.0
2x PCIe 3.0 x1 slots (from Z590 chipset)
Realtek® ALC897 Codec
7.1-Channel High Definition Audio
Supports 2-Way AMD CrossFire™ Technology
Continued on next page
5
Continued from previous page
1x HDMI 2.0b with HDR port, supports a maximum
resolution of 4K 60Hz */**
1x DisplayPort 1.4 port, supports a maximum resolution of
4K 60Hz */**
* Available only on processors featuring integrated graphics.
** Graphics specifications may vary depending on the CPU
installed.
1x Intel® I225-V 2.5Gbps LAN controller
Intel® Wi-Fi 6E AX210
The Wireless module is pre-installed in the M.2 (Key-E) slot
Supports MU-MIMO TX/RX, 2.4GHz/ 6GHz (160MHz) up to
2.4Gbps
Supports 802.11 a/ b/ g/ n/ ac/ ax
Supports Bluetooth® 5.2, FIPS, FISMA
6x SATA 6Gb/s ports (from Z590 chipset)
3x M.2 slots (Key M)
M2_1 slot (from CPU)*
Available only on 11th Gen Intel® CPU
Supports up to PCIe 4.0×4
Supports 2242/ 2260/ 2280/ 22110 storage devices
M2_2*, M2_3** slots (from Z590 chipset)
Support up to PCIe 3.0×4
Support up to SATA 6Gb/s
Support 2242/ 2260/ 2280 storage devices
Intel® Optane™ Memory Ready***
Support Intel® Smart Response Technology for Intel Core™
processors
* SATA2 will be unavailable when installing M.2 SATA SSD in
the M2_2 slot.
** SATA5 & SATA 6 will be unavailable when installing M.2
SSD in the M2_3 slot.
*** Before using Intel® Optane™ memory modules, please
ensure that you have updated the drivers and BIOS to the
latest version from MSI website.
Supports RAID 0, RAID 1, RAID 5 and RAID 10 for SATA
storage devices
Supports RAID 0 and RAID 1 for M.2 NVMe storage devices
Continued on next page
6
Continued from previous page
Intel® Z590 Chipset
1x USB 3.2 Gen 2×2 20Gbps Type-C port on the back
panel
2x USB 3.2 Gen 2 10Gbps ports (1 Type-C internal
connector and 1 Type-A port on the back panel)
6x USB 3.2 Gen 1 5Gbps ports (2 Type-A ports on the
back panel, and 4 ports are available through the internal
USB 3.2 Gen 1 5Gbps connectors)
USB 2.0 Hubs GL850G
4x USB 2.0 Type-A ports on the back panel
4x USB 2.0 ports are available through the internal USB
2.0 connectors
1x 24-pin ATX main power connector
1x 8-pin ATX 12V power connector
1x 4-pin ATX 12V power connector
1x 6-pin ATX PCIe power connector
6x SATA 6Gb/s connectors
3x M.2 slots (M-Key)
1x USB 3.2 Gen 2 10Gbps Type-C port
2x USB 3.2 Gen 1 5Gbps connectors (supports additional 4
USB 3.2 Gen 1 5Gbps ports)
2x USB 2.0 connectors (supports additional 4 USB 2.0 ports)
1x 4-pin CPU fan connector
1x 4-pin water-pump fan connector
6x 4-pin system fan connectors
1x Front panel audio connector
2x System panel connectors
1x Chassis Intrusion connector
1x Clear CMOS jumper
1x TPM module connector
1x Serial port connector
1x Tuning controller connector
1x TBT connector (Supports RTD3)
Continued on next page
7
Continued from previous page
1x 4-pin RGB LED connector
2x 3-pin RAINBOW LED connectors
4x EZ Debug LED
1x Flash BIOS Button
1x PS/2 keyboard/ mouse combo port
4x USB 2.0 Type-A ports
1x DisplayPort
1x HDMI port
1x LAN (RJ45) port
2x USB 3.2 Gen 1 5Gbps Type-A ports
1x USB 3.2 Gen 2 10Gbps Type-A port
1x USB 3.2 Gen 2×2 20Gbps Type-C port
2x Wi-Fi Antenna connectors (Only for Z590 PRO WIFI)
6x audio jacks
NUVOTON NCT6687-R Controller Chip
CPU/ System/ Chipset temperature detection
CPU/ System/ Pump fan speed detection
CPU/ System/ Pump fan speed control
ATX Form Factor
12 in. x 9.6 in. (30.5 cm x 24.4 cm)
1x 256 Mb flash
UEFI AMI BIOS
ACPI 6.2, SMBIOS 3.0
Multi-language
Drivers
MSI Center
Intel® Extreme Tuning Utility
CPU-Z MSI GAMING
Google Chrome™, Google Toolbar, Google Drive
Norton™ Internet Security Solution
Continued on next page
8
Continued from previous page
Mystic Light
LAN Manager
User Scenario
Hardware Monitor
Frozr AI Cooling
True Color
Live Update
Speed Up
Smart Tool
Super Charger
Audio
Audio Boost
Network
2.5G LAN
LAN Manager
Intel WiFi (Z590 PRO WIFI)
Cooling
Extended Heatsink Design
M.2 Shield Frozr
K7 thermal pad
Choke pad
Pump Fan
Smart Fan Control
LED
Mystic Light Extension (RAINBOW/RGB)
Mystic Light SYNC
EZ LED Control
EZ DEBUG LED
Continued on next page
9
Continued from previous page
Performance
Lightning Gen 4 PCI-E Slot
Lightning Gen 4 M.2
Multi GPU-CrossFire Technology
DDR4 Boost
Core Boost
Lightning USB 20G
USB 3.2 Gen 2 10G
USB with Type A+C
Front USB Type-C
Dual CPU Power
Supplemental PCIE Power Connector
2oz Copper thickened PCB
Protection
PCI-E Steel Armor
Experience
MSI Center
Frozr AI Cooling
Click BIOS 5
Flash BIOS Button
10
Off No link
Yellow Linked
Blinking Data activity
Off 10 Mbps connection
Green 100/ 1000 Mbps connection
Orange 2.5 Gbps connection
USB 3.2 Gen 1
5Gbps Type-A
Flash BIOS Button
PS/2 Combo port 2.5 Gbps LAN
DisplayPort
USB 2.0 Type-A
USB 2.0 Type-A Audio Ports
Wi-Fi Antenna connectors
(For Z590 PRO WIFI only)
USB 3.2 Gen 2×2
20Gbps Type-C USB 3.2 Gen 2
10Gbps Type-A
Flash BIOS
Port
2468
Line-Out/ Front Specker Out
Line-In
Rear Speaker Out
Center/ Subwoofer Out
Side Speaker Out
Mic In
: empty)
11
* Distance from the center of the CPU to the nearest DIMM slot.
SATA6
SATA5
SYS_FAN5
SYS_FAN4
JCOM1
JTBT1
JFP2
JTPM1
JRGB1
JCI1
M2_3
M2_2
M2_1
SYS_FAN1
JUSB4
JUSB5
JUSB3
JUSB1
JUSB2
PCIE_PWR1
SYS_FAN3
SYS_FAN2
CPU_FAN1
SYS_FAN6
PUMP_FAN1
PCI_E1
PCI_E2
PCI_E3
JBAT1
PCI_E4
JDASH1
Processor Socket
CPU_PWR1
CPU_PWR2
JRAINBOW2
JAUD1
JRAINBOW1
JFP1
ATX_PWR1
DIMMB1
DIMMB2
DIMMA1
DIMMA2
50.77mm*
12
Please install the CPU into the CPU socket as shown below.
Always unplug the power cord from the power outlet before installing or removing
the CPU.
Please retain the CPU protective cap after installing the processor. MSI will deal
with Return Merchandise Authorization (RMA) requests if only the motherboard
comes with the protective cap on the CPU socket.
When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink
is necessary to prevent overheating and maintain system stability.
your system.
Overheating can seriously damage the CPU and motherboard. Always make sure
the cooling fans work properly to protect the CPU from overheating. Be sure to apply
an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to
enhance heat dissipation.
Whenever the CPU is not installed, always protect the CPU socket pins by covering
the socket with the plastic cap.
If you purchased a separate CPU and heatsink/ cooler, Please refer to the docu-
mentation in the heatsink/ cooler package for more details about installation.
1
4
6
5
78
9
3
2
13
Please install the memory module into the DIMM slot as shown below.
DIMMB2
DIMMA2 DIMMA2
Please install the memory module into the DIMM slot as shown below.
1
1
2
3
3
2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
14
Always insert memory modules in the
To ensure system stability for Dual channel mode, memory modules must be of the
same type, number and density.
Some memory modules may operate at a lower frequency than the marked value
when overclocking due to the memory frequency operates dependent on its Serial
frequency if you want to operate the memory at the marked or at a higher frequency.
installation or overclocking.
The stability and compatibility of installed memory module depend on installed
CPU and devices when overclocking.
Please refer www.msi.com for more information on compatible memory.
unplug the power supply power cable from the power outlet. Read the expansion
card’s documentation to check for any necessary additional hardware or software
changes.
If you install a large and heavy graphics card, you need to use a tool such as
to support its weight to prevent deformation
of the slot.
For a single PCIe x16 expansion card installation with optimum performance, using
the slot is recommended.
: PCIe 4.0/ 3.0 x16 (From CPU)
: PCIe 3.0 x4 (From Z590 chipset)
: PCIe 3.0 x1 (From Z590 chipset)
: PCIe 3.0 x1 (From Z590 chipset)
15
These connectors connect to the switches and LEDs on the front panel.
1
2 10
9
+
+
+— ——
—
+
Power LED
HDD LED Reset Switch
Reserved
Power Switch 1 HDD LED + 2 Power LED +
3 HDD LED — 4 Power LED —
5 Reset Switch 6 Power Switch
7 Reset Switch 8 Power Switch
9 Reserved 10 No Pin
JFP2 1
+
+—
—
Speaker
Buzzer 1 Speaker — 2 Buzzer +
3 Buzzer — 4 Speaker +
HDD LED
RESET SW
HDD LED HDD LED —
HDD LED +
POWER LED —
POWER LED +
POWER LED
JFP1
This connector allow you to connect audio jacks on the front panel.
1
2 10
9
1 MIC L 2 Ground
3 MIC R 4 NC
5 Head Phone R 6 MIC Detection
7 SENSE_SEND 8 No Pin
9 Head Phone L 10 Head Phone Detection
16
These connectors are SATA 6Gb/s interface ports. Each connector can connect to one
SATA device.
SATA1
SATA3
SATA2
SATA6
SATA5
SATA4
SATA2 will be unavailable when installing M.2 SATA SSD in the M2_2 slot.
SATA5 & SATA 6 will be unavailable when installing M.2 SSD in the M2_3 slot.
Please do not fold the SATA cable at a 90-degree angle. Data loss may result
during transmission otherwise.
SATA cables have identical plugs on either sides of the cable. However, it is
saving purposes.
Please install the M.2 solid-state drive (SSD) into the M.2 slot as shown below.
1
3
Standoff
Supplied
M.2 screw 30º30º
2
17
These connectors allow you to connect an ATX power supply.
Make sure that all the power cables are securely connected to a proper ATX power
supply to ensure stable operation of the motherboard.
24
131
12
ATX_PWR1
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 Ground 15 Ground
4 +5V 16 PS-ON#
5 Ground 17 Ground
6 +5V 18 Ground
7 Ground 19 Ground
8 PWR OK 20 Res
9 5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 Ground
3
2 1
4CPU_PWR2 1 Ground 3 +12V
2 Ground 8 +12V
5
41
8
CPU_PWR1
1 Ground 5 +12V
2 Ground 6 +12V
3 Ground 7 +12V
4 Ground 8 +12V
1 3
64
PCIE_PWR1
1 +12V 4 Ground
2 +12V 5 Ground
3 +12V 6 Ground
18
This connector allows you to connect USB 3.2 Gen 1 5Gbps ports on the front panel.
1
10 11
20
1 Power 11 USB2.0+
2 USB3_RX_DN 12 USB2.0-
3 USB3_RX_DP 13 Ground
4 Ground 14 USB3_TX_C_DP
5 USB3_TX_C_DN 15 USB3_TX_C_DN
6 USB3_TX_C_DP 16 Ground
7 Ground 17 USB3_RX_DP
8 USB2.0- 18 USB3_RX_DN
9 USB2.0+ 19 Power
10 Ground 20 No Pin
Note that the Power and Ground pins must be connected correctly to avoid possible
damage.
These connectors allow you to connect USB 2.0 ports on the front panel.
Note that the VCC and Ground pins must be connected correctly to avoid possible
damage.
In order to recharge your iPad,iPhone and iPod through USB ports, please install
MSI Center utility.
1
2 10
9
1 VCC 2 VCC
3 USB0- 4 USB1-
5 USB0+ 6 USB1+
7 Ground 8 Ground
9 No Pin 10 NC
19
This connector allows you to connect USB 3.2 Gen 2 Type-C connector on the front
panel. The connector possesses a foolproof design. When you connect the cable, be
sure to connect it with the corresponding orientation.
JUSB1
USB Type-C Cable
USB Type-C port on the
front panel
This connector allows you to connect the add-on Thunderbolt I/O card.
1
2 16
15
1 TBT_Force_PWR 2 TBT_S0IX_Entry_REQ
3 TBT_CIO_Plug_Event# 4 TBT_S0IX_Entry_ACK
5 SLP_S3#_TBT 6 TBT_PSON_Override_N
7 SLP_S5#_TBT 8 Net Name
9 Ground 10 SMBCLK_VSB
11 DG_PEWake 12 SMBDATA_VSB
13 TBT_RTD3_PWR_EN 14 Ground
15 TBT_Card_DET_R# 12 PD_IRQ#
20
1
212
11
1 SPI Power 2 SPI Chip Select
3
Master In Slave Out
(SPI Data)
4
Master Out Slave In
(SPI Data)
5 Reserved 6 SPI Clock
7 Ground 8 SPI Reset
9 Reserved 10 No Pin
11 Reserved 12 Interrupt Request
This connector is for TPM (Trusted Platform Module). Please refer to the TPM
security platform manual for more details and usages.
Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC
Mode. PWM Mode fan connectors provide constant 12V output and adjust fan speed
with speed control signal. DC Mode fan connectors control fan speed by changing
voltage.
You can adjust fan speed in
1
1 Ground 2 +12V
3 Sense 4 Speed Control Signal
CPU_FAN1 PWM mode 2A 24W
PUMP_FAN1 PWM mode 3A 36W
SYS_FAN1~6 DC mode 1A 12W
1
1 Ground 2 Voltage Control
3 Sense 4 NC
21
This connector allows you to connect the chassis intrusion switch cable.
Normal
(default) Trigger the chassis
intrusion event
Connect the connector to the chassis intrusion switch/ sensor on the
chassis.
Close the chassis cover.
Go to .
Set to .
Press to save and exit and then press the key to select .
Once the chassis cover is opened again, a warning message will be displayed on
screen when the computer is turned on.
Go to .
Set to Reset.
Press to save and exit and then press the key to select .
This connector allows you to connect the optional serial port with bracket.
This connector is used to connect an optional Tuning Controller module.
1
2 10
9
1 DCD 2 SIN
3 SOUT 4 DTR
5 Ground 6 DSR
7 RTS 8 CTS
9 RI 10 No Pin
1
2 6
5
1 No pin 2 NC
3 MCU_SMB_SCL_M 4 MCU_SMB_SDA_M
5 VCC5 6 Ground
22
There is CMOS memory onboard that is external powered from a battery located on
the motherboard to save system configuration data. If you want to clear the system
configuration, set the jumpers to clear the CMOS memory.
Keep Data
(default) Clear CMOS/
Reset BIOS
Power off the computer and unplug the power cord.
Use a jumper cap to short for about 5-10 seconds.
Remove the jumper cap from .
Plug the power cord and power on the computer.
The JRAINBOW connectors allow you to connect the WS2812B Individually
Addressable RGB LED strips 5V.
Do not connect the wrong type of LED strips. The JRGB connector and the JRAINBOW
connector provide different voltages, and connecting the 5V LED strip to the JRGB
connector will result in damage to the LED strip.
The JRAINBOW connector supports up to 75 LEDs WS2812B Individually Address-
able RGB LED strips (5V/Data/Ground) with the maximum power rating of 3A (5V). In
the case of 20% brightness, the connector supports up to 200 LEDs.
before installing or removing the RGB LED strip.
Please use MSI’s software to control the extended LED strip.
11 +5V 2 Data
3 No Pin 4 Ground
23
These LEDs indicate the status of the motherboard.
— indicates CPU is not detected or fail.
— indicates DRAM is not detected or fail.
— indicates GPU is not detected or fail.
— indicates booting device is not detected or fail.
The JRGB connector allows you to connect the 5050 RGB LED strips 12V.
The JRGB connector supports up to 2 meters continuous 5050 RGB LED strips
(12V/G/R/B) with the maximum power rating of 3A (12V).
before installing or removing the RGB LED strip.
Please use MSI’s software to control the extended LED strip.
11 +12V 2 G
3 R 4 B
24
Please download and update the latest utilities and drivers at www.msi.com
Power on the computer.
Insert the Windows® 10 installation disc/USB into your computer.
Press the button on the computer case.
Press key during the computer POST (Power-On Self Test) to get into Boot
Menu.
Select the Windows® 10 installation disc/USB from the Boot Menu.
Press any key when screen shows
message.
Follow the instructions on the screen to install Windows® 10.
Start up your computer in Windows® 10.
Insert MSI® Drive disc into the optical drive.
Click the pop-up notification,
then select to open the installer. If you turn off the AutoPlay
feature from the Windows Control Panel, you can still manually execute the
from the root path of the MSI Drive disc.
The installer will find and list all necessary drivers in the tab.
Click the button in the lower-right corner of the window.
The drivers installation will then be in progress, after it has finished it will prompt
you to restart.
Click button to finish.
Restart your computer.
MSI Center is an application that helps you easily optimize game settings and
smoothly use content creation softwares. It also allows you to control and
synchronize LED light effects on PCs and other MSI products. With MSI Center, you
can customize ideal modes, monitor system performance, and adjust fan speed.
If you would like to know more information about MSI Center, please
refer to
http://download.msi.com/manual/mb/MSICENTER.pdf
or scan the QR code to access.
Functions may vary depending on the product you have.
25
MSI UEFI BIOS is compatible with UEFI (Unified Extensible Firmware Interface)
architecture. UEFI has many new functions and advantages that traditional BIOS
cannot achieve, and it will completely replace BIOS in the future. The MSI UEFI
BIOS uses UEFI as the default boot mode to take full advantage of the new chipset’s
capabilities.
The term BIOS in this user guide refers to UEFI BIOS unless otherwise noted.
Fast booting — UEFI can directly boot the operating system and save the BIOS self-
test process. And also eliminates the time to switch to CSM mode during POST.
Supports for hard drive partitions larger than 2 TB.
Supports more than 4 primary partitions with a GUID Partition Table (GPT).
Supports unlimited number of partitions.
Supports full capabilities of new devices — new devices may not provide backward
compatibility.
Supports secure startup — UEFI can check the validity of the operating system to
ensure that no malware tampers with the startup process.
— this motherboard supports only 64-bit
Windows 10 operating system.
— the system will detect your graphics card. When display a
warning message
We recommend that you to replace with a GOP/UEFI compatible graphics card or
using integrated graphics from CPU for having normal function.
Power on your computer.
Press key, when the
message appears on the screen during the boot process.
After entering the BIOS, you can check the at the top of the screen.
26
The default settings offer the optimal performance for system stability in normal
conditions. You should to avoid possible system
damage or failure booting unless you are familiar with BIOS.
BIOS items are continuously update for better system performance. Therefore, the
only. You could also refer to the information panel for BIOS item description.
The BIOS screens, options and settings will vary depending on your system.
Press key, when the
message appears on the screen during the boot process.
: General Help
: Add/ Remove a favorite item
: Enter Favorites menu
: Enter CPU Specifications menu
: Enter Memory-Z menu
: Load optimized defaults
: Switch between Advanced mode and EZ mode
: Load Overclocking Profile
: Save Overclocking Profile
: Save Change and Reset*
: Take a screenshot and save it to USB flash drive (FAT/ FAT32 format only).
: Enter Search page
* When you press F10, a confirmation window appears and it provides the
modification information. Select between Yes or No to confirm your choice.
If you’d like to know more instructions on setting up the BIOS,
please refer to
http://download.msi.com/manual/mb/Intel500BIOS.pdf
or scan the QR code to access.
27
You might need to restore the default BIOS setting to solve certain problems. There
are several ways to reset BIOS:
Go to BIOS and press to load optimized defaults.
Short the Clear CMOS jumper on the motherboard.
Press the Clear CMOS button on the rear I/O panel.
Be sure the computer is off before clearing CMOS data. Please refer to the Clear
CMOS jumper/ button section for resetting BIOS.
Before updating:
Please download the latest BIOS file that matches your motherboard model from MSI
website. And then save the BIOS file into the USB flash drive.
Updating BIOS:
Insert the USB flash drive that contains the update file into the USB port.
Please refer the following methods to enter flash mode.
Reboot and press key during POST and click on to reboot the
system.
Reboot and press key during POST to enter BIOS. Click the
button and click on to reboot the system.
Select a BIOS file to perform the BIOS update process.
When prompted click on to start recovering BIOS.
After the flashing process is 100% completed, the system will reboot
automatically.
28
Before updating:
Make sure the LAN driver is already installed and the internet connection is set
properly.
Please close all other application software before updating the BIOS.
To update BIOS:
Install and launch MSI Center and go to page.
Select and click on button.
Select the BIOS file and click on button.
The installation reminder will appear, then click the button on it.
The system will automatically restart to update BIOS.
After the flashing process is 100% completed, the system will restart
automatically.
Please download the latest BIOS file that matches your motherboard model from
the MSI® website.
Rename the BIOS file to , and save it to the root of your USB flash drive.
Connect the power supply to and . (No need to install
CPU and memory.)
Plug the USB flash drive that contains the MSI.ROM file into the
on the rear I/O panel.
Press the Button to flash BIOS, and the LED starts flashing.
The LED will be turned off when the process is completed.
1
3
4
10
………………………………………………………………………………..10
…………………………………………………………………………………….10
11
…………………………………………………………………………………………………….12
…………………………………………………………………………………………………..13
……………………………………………………………………………..14
…………………………………………………………………………15
…………………………………………………………………………….15
………………………………………………………………………..16
……………………………………………………………………………..16
ATX_PWR1, CPU_PWR1~2, PCIE_PWR1:
………………………………………….17
……………………………………………………………………………..18
…………………………………………………………..18
……………………………………………………………….19
……………………………………………………………………19
………………………………………….20
……………………………………………………………………………….20
…………………………………………………………………………………..21
…………………………………………………………………………….21
……………………………………………………………………….21
…………………………………………………………22
……………………………………………22
……………………………………………………………………………….23
……………………………………………………………………………………………..23
24
Windows® ……………………………………………………………………………………24
…………………………………………………………………………………………24
……………………………………………………………………………………………………..24
MSI®
2
25
……………………………………………………………………………………..26
……………………………………………………………………………………………………26
……………………………………………………………………………………….26
……………………………………………………………………………………………………27
………………………………………………………………………………..27
3
4
®
x16/ x4
PCI_E1 (CPU)
PCI_E3 (Z590 )
7.1-
5
/**
/**
M2_1 (CPU)*
M2_2*, M2_3** (Z590 )
6
USB 2.0 Hubs GL850G
ATX PCIe
SAT
7
LED
12 in. x 9.6 in. (30.5 cm x 24.4 cm)
UEFI AMI BIOS
ACPI 6.2, SMBIOS 3.0
CPU-Z MSI GAMING
8
True Color
2.5G LAN
LAN
WiFi (Z590 PRO WIFI)
M.2
LED
(RAINBOW/RGB)
EZ LED
EZ LED
9
Gen 4 M.2
DDR4
USB 20G
USB 3.2 Gen 2 10G
2oz Copper thickened PCB
MSI
10
USB 3.2 Gen 1
2.5 Gbps LAN
USB 3.2 Gen 2×2
USB 3.2 Gen 2
2468
11
SATA6
SATA5
SYS_FAN5
SYS_FAN4
JCOM1
JTBT1
JFP2
JTPM1
JRGB1
JCI1
M2_3
M2_2
M2_1
SYS_FAN1
JUSB4
JUSB5
JUSB3
JUSB1
JUSB2
PCIE_PWR1
SYS_FAN3
SYS_FAN2
CPU_FAN1
SYS_FAN6
PUMP_FAN1
PCI_E1
PCI_E2
PCI_E3
JBAT1
PCI_E4
JDASH1
CPU_PWR1
CPU_PWR2
JRAINBOW2
JAUD1
JRAINBOW1
JFP1
ATX_PWR1
DIMMB1
DIMMB2
DIMMA1
DIMMA2
50.77mm*
12
1
4
6
5
78
9
3
2
13
DIMMB2
DIMMA2 DIMMA2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
1
1
2
3
3
2
14
: PCIe 4.0/ 3.0 x16 (CPU)
15
1
2 10
9
+
+
+— ——
—
+
HDD LED
Reserved
1 HDD LED + 2 Power LED +
3 HDD LED — 4 Power LED —
5 Reset Switch 6 Power Switch
7 Reset Switch 8 Power Switch
9 Reserved 10 No Pin
JFP2 1
+
+—
—
Speaker
Buzzer 1 Speaker — 2 Buzzer +
3 Buzzer — 4 Speaker +
HDD LED
RESET SW
HDD LED HDD LED —
HDD LED +
POWER LED —
POWER LED +
POWER LED
JFP1
1
2 10
9
1 MIC L 2 Ground
3 MIC R 4 NC
5 Head Phone R 6 MIC Detection
7 SENSE_SEND 8 No Pin
9 Head Phone L 10 Head Phone Detection
16
SATA1
SATA3
SATA2
SATA6
SATA5
SATA4
1
3
30º30º
2
17
24
131
12
ATX_PWR1
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 Ground 15 Ground
4 +5V 16 PS-ON#
5 Ground 17 Ground
6 +5V 18 Ground
7 Ground 19 Ground
8 PWR OK 20 Res
9 5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 Ground
3
2 1
4CPU_PWR2 1 Ground 3 +12V
2 Ground 8 +12V
5
41
8
CPU_PWR1
1 Ground 5 +12V
2 Ground 6 +12V
3 Ground 7 +12V
4 Ground 8 +12V
1 3
64
PCIE_PWR1
1 +12V 4 Ground
2 +12V 5 Ground
3 +12V 6 Ground
18
1
10 11
20
1 Power 11 USB2.0+
2 USB3_RX_DN 12 USB2.0-
3 USB3_RX_DP 13 Ground
4 Ground 14 USB3_TX_C_DP
5 USB3_TX_C_DN 15 USB3_TX_C_DN
6 USB3_TX_C_DP 16 Ground
7 Ground 17 USB3_RX_DP
8 USB2.0- 18 USB3_RX_DN
9 USB2.0+ 19 Power
10 Ground 20 No Pin
1
2 10
9
1 VCC 2 VCC
3 USB0- 4 USB1-
5 USB0+ 6 USB1+
7 Ground 8 Ground
9 No Pin 10 NC
19
JUSB1
1
2 16
15
1 TBT_Force_PWR 2 TBT_S0IX_Entry_REQ
3 TBT_CIO_Plug_Event# 4 TBT_S0IX_Entry_ACK
5 SLP_S3#_TBT 6 TBT_PSON_Override_N
7 SLP_S5#_TBT 8 Net Name
9 Ground 10 SMBCLK_VSB
11 DG_PEWake 12 SMBDATA_VSB
13 TBT_RTD3_PWR_EN 14 Ground
15 TBT_Card_DET_R# 12 PD_IRQ#
20
1
1 Ground 2 +12V
3 Sense 4 Speed Control Signal
CPU_FAN1 2A 24W
PUMP_FAN1 3A 36W
SYS_FAN1~6 1A 12W
1
1 Ground 2 Voltage Control
3 Sense 4 NC
1
212
11
1 SPI Power 2 SPI Chip Select
3
Master In Slave Out
(SPI Data)
4
Master Out Slave In
(SPI Data)
5 Reserved 6 SPI Clock
7 Ground 8 SPI Reset
9 Reserved 10 No Pin
11 Reserved 12 Interrupt Request
21
1
2 10
9
1 DCD 2 SIN
3 SOUT 4 DTR
5 Ground 6 DSR
7 RTS 8 CTS
9 RI 10 No Pin
1
2 6
5
1 No pin 2 NC
3 MCU_SMB_SCL_M 4 MCU_SMB_SDA_M
5 VCC5 6 Ground
22
11 +5V 2 Data
3 No Pin 4 Ground
23
11 +12V 2 G
3 R 4 B
24
http://download.msi.com/manual/mb/MSICENTER.pdf
25
,
26
http://download.msi.com/manual/mb/Intel500BIOSkr.pdf
27
®
28
1
3
4
10
Tableau explicatif de l’état de la LED du port LAN …………………………………………..10
Configuration des ports audio ……………………………………………………………………….10
11
Socket Processeur ………………………………………………………………………………………12
Slots DIMM …………………………………………………………………………………………………13
PCI_E1~4 : Slots d’extension PCIe …………………………………………………………………14
JFP1, JFP2 : Connecteurs de panneau avant ………………………………………………….15
JAUD1 : Connecteur audio avant……………………………………………………………………15
SATA1~6 : Connecteurs SATA 6 Gb/s …………………………………………………………….16
M2_1~3 : Slots M.2 (Touche M) ……………………………………………………………………..16
ATX_PWR1, CPU_PWR1~2, PCIE_PWR1 : Connecteurs d’alimentation ……………..17
JUSB1~2 : Connecteurs USB 2.0 …………………………………………………………………..18
JUSB3~4 : Connecteurs USB 3.2 Gen 1 5 Gb/s ……………………………………………….18
JUSB1 : Connecteur USB 3.2 Gen 2 Type-C ……………………………………………………19
JTBT1 : Connecteur de carte additionnelle Thunderbolt ………………………………….19
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6 : Connecteurs de ventilateur ………………20
JTPM1 : Connecteur de module TPM ……………………………………………………………..20
JCI1 : Connecteur intrusion châssis ………………………………………………………………21
JCOM1 : Connecteur de port série …………………………………………………………………21
JDASH1 : Connecteur du contrôleur de réglages…………………………………………….21
JBAT1 : Cavalier Clear CMOS (Réinitialiser le BIOS) ………………………………………..22
JRAINBOW1~2 : Connecteurs LED RGB adressables ………………………………………22
JRGB1 : Connecteur LED RGB ………………………………………………………………………23
EZ Debug LED ……………………………………………………………………………………………..23
23
Installer Windows® 10 ………………………………………………………………………………….23
Installer les pilotes ………………………………………………………………………………………24
MSI Center ………………………………………………………………………………………………….24
Merci d’avoir acheté la carte mère MSI®
. Ce guide d’utilisation fournit des informations
sur le schéma, la vue d’ensemble des composants, la con-
2
25
Configuration du BIOS ………………………………………………………………………………….26
Entrer dans l’interface Setup du BIOS ……………………………………………………………26
Guide d’utilisation du BIOS ……………………………………………………………………………26
Réinitialiser le BIOS …………………………………………………………………………………….27
Mettre le BIOS à jour ……………………………………………………………………………………27
3
Les composants dans l’emballage peuvent être endommagés par des décharges
électrostatiques (ESD). Pour vous assurer de correctement monter votre ordinateur,
veuillez vous référer aux instructions ci-dessous.
Assurez-vous de bien connecter tous les composants. En cas de mauvaise
connexion, il se peut que l’ordinateur ne reconnaisse pas le composant et que le
démarrage échoue.
Veuillez tenir la carte mère par les bords pour éviter de toucher les composants
sensibles.
Il est recommandé de porter un bracelet antistatique lors de la manipulation de la
carte mère pour prévenir tout dommage. Si vous n’avez pas de bracelet antistatique,
touchez un objet métallique relié à la terre avant de manipuler la carte mère afin de
vous décharger de votre charge statique. Touchez régulièrement l’objet métallique
pendant toute la manipulation.
Tant que la carte mère n’est pas installée, conservez-la dans un récipient protégé
contre les ondes électrostatiques ou sur une couche antistatique.
Avant de démarrer l’ordinateur, vérifiez si toutes les vis et les composants
métalliques sont bien fixés sur la carte mère ou ailleurs dans le boîtier de
l’ordinateur.
Ne démarrez pas l’ordinateur avant d’avoir terminé l’installation. Ceci peut
endommager les composants ou vous blesser.
Si vous avez besoin d’aide pendant l’installation, veuillez consulter un technicien
informatique certifié.
Avant d’installer les composants d’ordinateur, veuillez toujours mettre hors
tension et débrancher le cordon d’alimentation.
Gardez ce manuel pour références futures.
Protégez ce manuel contre l’humidité.
Avant de brancher le bloc d’alimentation sur la sortie électrique, veuillez
vous assurer que la tension de la sortie électrique est bien égale à celle du bloc
d’alimentation.
Placez le cordon d’alimentation de façon à éviter que l’on marche dessus. Ne posez
rien sur le cordon d’alimentation.
Veuillez prêter attention à toutes les alertes et remarques indiquées sur la carte
mère.
Dans un cas comme ci-dessous, faites appel au service autorisé pour vérifier votre
carte mère :
Un liquide a pénétré dans l’ordinateur.
La carte mère a été exposée à de l’humidité.
La carte mère ne fonctionne pas comme indiqué dans les instructions.
La carte mère est tombée par terre et a été endommagée.
La carte mère est cassée.
Ne pas mettre la carte mère dans un environnement dont la température est
supérieure à 60 °C (140 °F) sous peine de l’endommager.
4
Support des processeurs Intel® Core™ de 10ème génération,
Intel® Core™ de 11ème génération, Pentium® Gold et Celeron®
Socket LGA1200
* Veuillez vous au site www.intel.com pour plus d’informations
de compatibilité.
Chipset Intel® Z590
4 x slots pour mémoire DDR4, support jusqu’à 128 Go*
Support 1R 2133/ 2666/ 2933 MHz pour processeur Intel® de
10ème génération (par JEDEC et POR)
Support 1R 2133/ 2666/ 2933/ 3200 MHz pour processeur
Intel® de 11ème génération (par JEDEC et POR)
Fréquence d’overclocking maximale :
La fréquence maximale en mode 1DPC 1R monte
jusqu’à 5333 MHz
La fréquence maximale en mode 1DPC 2R monte
jusqu’à 4700+ MHz
La fréquence maximale en mode 2DPC 1R monte
jusqu’à 4400+ MHz
La fréquence maximale en mode 2DPC 2R monte
jusqu’à 4000+ MHz
Support mode double canal
Support non-ECC, mémoire un-buffered
Support Intel® Extreme Memory Profile (XMP)
* Veuillez vous référer au site www.msi.com pour plus
d’informations sur la mémoire compatible.
2 x slots PCIe x16
Support x16/ x4
PCI_E1 (depuis CPU)
Support jusqu’à PCIe 4.0 pour processeur Intel® de
11ème génération
Support jusqu’à PCIe 3.0 pour processeur Intel® de
10ème génération
PCI_E3 (depuis Chipset Z590)
Support jusqu’à PCIe 3.0
2 x slots PCIe 3.0 x1 (depuis Chipset Z590)
Realtek® ALC897 Codec
Audio haute définition 7.1
Suite du tableau sur la page suivante
5
Suite du tableau sur la page précédente
Support de la technologie AMD CrossFire™ 2-Way
1 x port HDMI 2.0b avec HDR, supportant une résolution
maximum de 4K 60 Hz */**
1 x port DisplayPort 1.4, supportant une résolution
maximum de 4K 60 Hz */**
* Disponible uniquement pour le processeur avec puce
graphique intégrée.
** Les caractéristiques des cartes graphiques peuvent varier
en fonction du processeur installé.
6 x ports SATA 6 Gb/s (depuis Chipset Z590)
3 x slots M.2 (Touche M)
Le slot M2_1 (depuis CPU)*
Disponible uniquement sur les processeurs Intel®
de 11ème génération
Support jusqu’à PCIe 4.0×4
Support des périphériques de stockage 2242/ 2260/
2280/ 22110
Les slots M2_2*, M2_3** (depuis Chipset Z590)
Support jusqu’à PCIe 3.0×4
Support jusqu’à SATA 6 Gb/s
Support des périphériques de stockage 2242/ 2260/
2280
Intel® Optane™ Memory Ready***
Support technologie Intel® Smart Response pour les
processeurs Intel Core™
* Le connecteur SATA2 est indisponible lorsqu’un SSD M.2
SATA est installé dans le slot M2_2.
** Les connecteurs SATA5 et SATA6 sont indisponibles
lorsqu’un SSD M.2 est installé dans le slot M2_3.
*** Avant d’utiliser les modules de mémoire Intel® Optane™,
veuillez vous assurer d’avoir mis à jour les pilotes et le BIOS
avec la dernière version disponible sur le site officiel MSI.
Intel® Wi-Fi 6E AX210
Le module sans-fil est pré-installé dans le slot M.2 (Touche
E)
Support MU-MIMO TX/RX, 2,4 GHz / 6 GHz (160 MHz) jusqu’à
2,4 Gb/s
Support 802.11 a/ b/ g/ n/ ac/ ax
Support Bluetooth® 5.2, FIPS, FISMA
Suite du tableau sur la page suivante
6
Suite du tableau sur la page précédente
1 x contrôleur Intel® I225-V 2,5 Gb/s LAN
Support RAID 0, RAID 1, RAID 5 et RAID 10 pour les
périphériques de stockage SATA
Support RAID 0 et RAID 1 pour les périphériques de
stockage M.2 NVMe
Chipset Intel® Z590
1 x port USB 3.2 Gen 2×2 20 Gb/s Type-C sur le panneau
arrière
2 x ports USB 3.2 Gen 2 10 Gb/s (1 connecteur interne
Type-C et 1 port Type-A sur le panneau arrière)
6 x ports USB 3.2 Gen 1 5 Gb/s (2 ports Type-A sur le
panneau arrière, 4 ports disponibles par l’intermédiaire
des connecteurs USB 3.2 Gen 1 5 Gb/s internes)
USB 2.0 Hubs GL850G
4 x ports USB 2.0 Type-A sur le panneau arrière
4 x ports USB 2.0 disponibles par l’intermédiaire des
connecteurs USB 2.0 internes
1 x connecteur LED RGB à 4 broches
2 x connecteurs LED RAINBOW à 3 broches
4 x EZ Debug LED
Suite du tableau sur la page suivante
7
Suite du tableau sur la page précédente
1 x connecteur d’alimentation principal ATX à 24 broches
1 x connecteur d’alimentation ATX 12 V à 8 broches
1 x connecteur d’alimentation ATX 12 V à 4 broches
1 x connecteur d’alimentation ATX PCIe à 6 broches
6 x connecteurs SATA 6 Gb/s
3 x slots M.2 (Touche M)
1 x port USB 3.2 Gen 2 10 Gb/s Type-C
2 x connecteurs USB 3.2 Gen 1 5 Gb/s (support de 4 autres
ports USB 3.2 Gen 1 5 Gb/s)
2 x connecteurs USB 2.0 (support de 4 autres ports USB 2.0)
1 x connecteur de ventilateur CPU à 4 broches
1 x connecteur de ventilateur à 4 broches pour la pompe
à eau
6 x connecteurs de ventilateur système à 4 broches
1 x connecteur audio avant
2 x connecteurs de panneau système
1 x connecteur intrusion châssis
1 x cavalier Clear CMOS
1 x connecteur de module TPM
1 x connecteur de port série
1 x connecteur du contrôleur de réglages
1 x connecteur TBT (support RTD3)
1 x bouton Flash BIOS
1 x port combo souris/clavier PS/2
4 x ports USB 2.0 Type-A
1 x DisplayPort
1 x port HDMI
1 x port LAN (RJ45)
2 x ports USB 3.2 Gen 1 5 Gb/s Type-A
1 x port USB 3.2 Gen 2 10 Gb/s Type-A
1 x port USB 3.2 Gen 2×2 20 Gb/s Type-C
2 x connecteurs d’antenne Wi-Fi (Uniquement pour Z590
PRO WIFI)
6 x jacks audio
Suite du tableau sur la page suivante
8
Suite du tableau sur la page précédente
Contrôleur NUVOTON NCT6687-R
Détection de la température du CPU, du système et du
Chipset
Détection de la vitesse du ventilateur du CPU, du système et
du ventilateur de pompe
Contrôle de la vitesse du ventilateur du CPU, du système et
du ventilateur de pompe
Format ATX
30,5 cm x 24,4 cm (12” x 9,6”)
1 x flash 256 Mb
UEFI AMI BIOS
ACPI 6.2, SMBIOS 3.0
Multilingue
Pilotes
MSI Center
Intel® Extreme Tuning Utility
CPU-Z MSI GAMING
Google Chrome™, Google Toolbar, Google Drive
Norton™ Internet Security Solution
Mystic Light
LAN Manager
User Scenario
Hardware Monitor
Frozr AI Cooling
True Color
Live Update
Speed Up
Smart Tool
Super Charger
Network
2,5 G LAN
LAN Manager
Intel WiFi (Z590 PRO WIFI)
Suite du tableau sur la page suivante
9
Suite du tableau sur la page précédente
Audio
Audio Boost
Cooling
Extended Heatsink Design
M.2 Shield Frozr
K7 thermal pad
Choke pad
Pump Fan
Smart Fan Control
LED
Mystic Light Extension (RAINBOW/RGB)
Mystic Light SYNC
EZ LED Control
EZ DEBUG LED
Performance
Slot Lightning Gen 4 PCI-E
Lightning Gen 4 M.2
Technologie Multi GPU-CrossFire
DDR4 Boost
Core Boost
Lightning USB 20G
USB 3.2 Gen 2 10 G
USB de Type A+C
Front USB Type-C
Dual CPU Power
Supplemental PCIE Power Connector
2oz Copper thickened PCB
Protection
PCI-E Steel Armor
Expérience
MSI Center
Frozr AI Cooling
Click BIOS 5
Bouton Flash BIOS
10
Etat
Eteint Pas de connexion
Jaune Connexion correcte
Clignote Activité en cours
Etat
Eteint 10 Mb/s
Vert 100 / 1000 Mb/s
Orange 2,5 Gb/s
USB 3.2 Gen 1
5 Gb/s Type-A
Bouton Flash BIOS
Port combo PS/2 2,5 Gb/s LAN
DisplayPort
USB 2.0 Type-A
USB 2.0 Type-A Ports audio
Connecteurs d’antenne
Wi-Fi (Uniquement pour
Z590 PRO WIFI)
USB 3.2 Gen 2×2
20 Gb/s Type-C USB 3.2 Gen 2
10 Gb/s Type-A
Port Flash
BIOS
2 4 6 8
Sortie Ligne / Sortie casque avant
Entrée Ligne
Sortie audio haut-parleur arrière
Sortie centre / Caisson de basse
Sortie audio haut-parleur côté
Entrée Microphone
Espace : vide)
11
* Distance entre le centre du CPU et le slot DIMM le plus proche.
SATA6
SATA5
SYS_FAN5
SYS_FAN4
JCOM1
JTBT1
JFP2
JTPM1
JRGB1
JCI1
M2_3
M2_2
M2_1
SYS_FAN1
JUSB4
JUSB5
JUSB3
JUSB1
JUSB2
PCIE_PWR1
SYS_FAN3
SYS_FAN2
CPU_FAN1
SYS_FAN6
PUMP_FAN1
PCI_E1
PCI_E2
PCI_E3
JBAT1
PCI_E4
JDASH1
Socket processeur
CPU_PWR1
CPU_PWR2
JRAINBOW2
JAUD1
JRAINBOW1
JFP1
ATX_PWR1
DIMMB1
DIMMB2
DIMMA1
DIMMA2
50.77mm*
12
Installer le processeur dans le socket comme indiqué ci-dessous.
Avant d’installer ou de retirer le processeur du socket, veillez à toujours débranch-
er le câble d’alimentation de la prise électrique.
Veuillez garder le capot de protection du processeur après l’installation du
processeur. Selon les exigences de RMA (Return Merchandise Authorization), MSI
n’acceptera pas les cartes mère dont le capot de protection aura été retiré.
Lors de l’installation d’un processeur, n’oubliez pas d’installer un ventilateur pour
processeur. Un ventilateur de processeur est nécessaire pour protéger le proces—
Assurez-vous de l’étanchéité entre le ventilateur et le processeur avant de démar-
rer votre système.
Assurez-vous toujours que le système de refroidissement fonctionne correctement
de pâte thermique (ou adhésif thermique) entre le processeur et le système de
Quand le processeur n’est pas installé, protégez toujours les broches de l’em-
placement du processeur avec le couvercle dédié.
Si vous avez achetez un processeur indépendamment du ventilateur, veuillez vous
référer à la documentation dans le paquet du ventilateur pour plus d’informations
concernant l’installation.
1
4
6
5
78
9
3
2
13
Insérer le module de mémoire dans le slot DIMM comme indiqué ci-dessous.
DIMMB2
DIMMA2 DIMMA2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
1
1
2
3
3
2
14
Veillez à toujours insérer un module de mémoire dans le slot en premier.
Pour garantir la stabilité du système au mode de double canal, assurez-vous
d’installer les modules de mémoire du même type, du même nombre et de la même
densité.
Certaines mémoires peuvent fonctionner à une fréquence réduite par rapport à
la valeur indiquée lors de l’overclocking car la fréquence d’opération de mémoire
dépend du Serial Presence Detect (SPD). Rendez-vous sur le BIOS et choisissez la
fonction DRAM Frequency pour régler la fréquence de mémoire si vous voulez faire
fonctionner la mémoire à la fréquence indiquée ou à une fréquence plus élevée.
Il est recommandé d’utiliser un système de refroidissement qui sera capable de
overclocking.
La stabilité et la compatibilité du module de mémoire lors de l’overclocking dépen-
dent du processeur et des périphériques installés.
Veuillez vous référer au site www.msi.com pour plus d’informations sur la
mémoire compatible.
Veillez à toujours mettre l’ordinateur hors tension et à débrancher le cordon d’al-
imentation avant d’installer les cartes d’extension. Référez-vous à la documentation
Si vous installez une carte graphique lourde, il vous faut utiliser un outil comme
la pour supporter son poids et pour éviter la
déformation du slot.
Si vous choisissez d’installer une seule carte d’extension PCIe x16, nous vous
recommandons d’utiliser le slot
: PCIe 4.0 / 3.0 x16 (CPU)
: PCIe 3.0 x4 (Chipset Z590)
: PCIe 3.0 x1 (Chipset Z590)
: PCIe 3.0 x1 (Chipset Z590)
15
Ces connecteurs se lient aux interrupteurs et indicateurs LED du panneau avant.
1
2 10
9
+
+
+— ——
—
+
Power LED
HDD LED Reset Switch
Reserved
Power Switch 1 HDD LED + 2 Power LED +
3 HDD LED — 4 Power LED —
5 Reset Switch 6 Power Switch
7 Reset Switch 8 Power Switch
9 Reserved 10 No Pin
JFP2 1
+
+—
—
Speaker
Buzzer 1 Speaker — 2 Buzzer +
3 Buzzer — 4 Speaker +
HDD LED
RESET SW
HDD LED HDD LED —
HDD LED +
POWER LED —
POWER LED +
POWER LED
JFP1
Ce connecteur se lie aux jacks audio du panneau avant.
1
2 10
9
1 MIC L 2 Ground
3 MIC R 4 NC
5 Head Phone R 6 MIC Detection
7 SENSE_SEND 8 No Pin
9 Head Phone L 10 Head Phone Detection
16
Ces connecteurs utilisent une interface SATA 6 Gb/s. Chaque connecteur peut être
relié à un appareil SATA.
SATA1
SATA3
SATA2
SATA6
SATA5
SATA4
Le connecteur SATA2 est indisponible lorsqu’un SSD M.2 SATA est installé dans le
slot M2_2.
Les connecteurs SATA5 et SATA6 sont indisponibles lorsqu’un SSD M.2 est installé
dans le slot M2_3.
Veuillez ne pas plier les câbles SATA à 90° car cela pourrait entraîner une perte de
données pendant la transmission.
Les câbles SATA disposent de prises identiques sur chaque côté. Néanmoins, il est
recommandé de connecter la prise plate sur la carte mère pour un gain d’espace.
Installer un SSD M.2 dans le slot M.2 comme indiqué ci-dessous.
1
3
Entretoise
Vis M.2 30º30º
2
17
Ces connecteurs vous permettent de relier une alimentation ATX.
Veuillez vous assurer que tous les câbles d’alimentation sont branchés aux
connecteurs adéquats afin garantir une opération stable de la carte mère.
24
131
12
ATX_PWR1
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 Ground 15 Ground
4 +5V 16 PS-ON#
5 Ground 17 Ground
6 +5V 18 Ground
7 Ground 19 Ground
8 PWR OK 20 Res
9 5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 Ground
3
2 1
4CPU_PWR2 1 Ground 3 +12V
2 Ground 8 +12V
5
41
8
CPU_PWR1
1 Ground 5 +12V
2 Ground 6 +12V
3 Ground 7 +12V
4 Ground 8 +12V
1 3
64
PCIE_PWR1
1 +12V 4 Ground
2 +12V 5 Ground
3 +12V 6 Ground
18
Ce connecteur vous permet de relier un port USB 3.2 Gen 1 5 Gb/s sur le panneau
avant.
1
10 11
20
1 Power 11 USB2.0+
2 USB3_RX_DN 12 USB2.0-
3 USB3_RX_DP 13 Ground
4 Ground 14 USB3_TX_C_DP
5 USB3_TX_C_DN 15 USB3_TX_C_DN
6 USB3_TX_C_DP 16 Ground
7 Ground 17 USB3_RX_DP
8 USB2.0- 18 USB3_RX_DN
9 USB2.0+ 19 Power
10 Ground 20 No Pin
Notez que les câbles d’alimentation et de terre doivent être branchés correctement
afin d’éviter d’endommager la carte.
Ces connecteurs vous permettent de relier des ports USB 2.0 sur le panneau avant.
d’éviter tout dommage sur la carte mère.
Pour recharger votre iPad, iPhone et iPod par l’intermédiaire d’un port USB,
veuillez installer l’utilitaire MSI® CENTER.
1
2 10
9
1 VCC 2 VCC
3 USB0- 4 USB1-
5 USB0+ 6 USB1+
7 Ground 8 Ground
9 No Pin 10 NC
19
Ce connecteur vous permet de relier un port USB 3.2 Gen 2 Type-C sur le panneau
avant. Pour plus de sécurité, ce connecteur a été conçu pour offrir une excellente
robustesse. Quand vous connectez le câble, assurez-vous de le brancher dans le bon
sens.
JUSB1
Câble USB Type-C
Port USB Type-C sur le
panneau avant
Ce connecteur vous permet de relier une carte additionnelle Thunderbolt E/S.
1
2 16
15
1 TBT_Force_PWR 2 TBT_S0IX_Entry_REQ
3 TBT_CIO_Plug_Event# 4 TBT_S0IX_Entry_ACK
5 SLP_S3#_TBT 6 TBT_PSON_Override_N
7 SLP_S5#_TBT 8 Net Name
9 Ground 10 SMBCLK_VSB
11 DG_PEWake 12 SMBDATA_VSB
13 TBT_RTD3_PWR_EN 14 Ground
15 TBT_Card_DET_R# 12 PD_IRQ#
20
Ce connecteur est relié à un module TPM (Trusted Platform Module). Veuillez vous
référer au manuel du module TPM pour plus d’informations.
Les connecteurs de ventilateur peuvent être utilisés en mode PWM (Pulse Width
Modulation) et en mode DC. En mode PWM, les connecteurs fournissent une sortie
de 12 V constante et ajustent la vitesse du ventilateur avec un signal de contrôle
de vitesse. En mode DC, les connecteurs contrôlent la vitesse du ventilateur en
modifiant la tension.
Vous pouvez ajuster la vitesse du ventilateur dans le .
1
1 Ground 2 +12V
3 Sense 4 Speed Control Signal
CPU_FAN1 mode PWM 2 A 24 W
PUMP_FAN1 mode PWM 3 A 36 W
SYS_FAN1~6 mode DC 1 A 12 W
1
1 Ground 2 Voltage Control
3 Sense 4 NC
1
212
11
1 SPI Power 2 SPI Chip Select
3
Master In Slave Out
(SPI Data)
4
Master Out Slave In
(SPI Data)
5 Reserved 6 SPI Clock
7 Ground 8 SPI Reset
9 Reserved 10 No Pin
11 Reserved 12 Interrupt Request
21
Ce connecteur est relié à un câble d’interrupteur intrusion châssis.
Normal
(défaut) Commencer l’activité
instrusion châssis
Reliez le connecteur à l’interrupteur ou au capteur d’intrusion châssis situé
sur le boîtier du PC.
Fermez le couvercle du boîtier.
Allez dans le
.
Réglez sur .
Appuyez sur pour sauvegarder et quitter. Ensuite appuyez sur la touche
pour choisir .
Désormais, si le boîtier du PC est ouvert quand l’ordinateur est allumé, vous
recevrez un message d’alerte à l’écran.
Allez dans le
.
Mettez en .
Appuyez sur pour sauvegarder et quitter. Ensuite appuyez sur la touche
pour choisir .
Ce connecteur vous permet de relier un port série en option.
Ce connecteur est utilisé pour connecter un contrôleur de réglage (selon modèle).
1
2 10
9
1 DCD 2 SIN
3 SOUT 4 DTR
5 Ground 6 DSR
7 RTS 8 CTS
9 RI 10 No Pin
1
2 6
5
1 No pin 2 NC
3 MCU_SMB_SCL_M 4 MCU_SMB_SDA_M
5 VCC5 6 Ground
22
Une mémoire CMOS est intégrée et est alimentée en externe par une batterie située
sur la carte mère afin de conserver les données de configuration système. Si vous
souhaitez nettoyer la configuration système, placez le cavalier sur Effacer CMOS de
manière à nettoyer la mémoire CMOS.
Conserver
les données
(défaut)
Effacer le CMOS/
Réinitialiser le BIOS
Eteignez l’ordinateur et débranchez le câble d’alimentation de la prise électrique.
Utilisez un couvercle de cavalier pour fermer pendant 5 à 10 secondes.
Enlevez le couvercle de cavalier du .
Branchez de nouveau le câble d’alimentation à votre ordinateur et allumez-le.
Le connecteur JRAINBOW vous permet de connecter un ruban à LED RGB WS2812B
adressable individuellement 5 V.
Faites attention à bien connecter le bon type de ruban LED. Le connecteur JRGB et
le connecteur JRAINBOW fournissent des tensions différentes. La connexion d’un
ruban LED 5 V au connecteur JRGB peut endommager le ruban.
Le connecteur JRAINBOW supporte jusqu’à des rubans 75 LEDs WS2812B adress-
ables individuellement (5 V/Data/Ground) avec une puissance nominale maximale de
3 A (5 V). Dans le cas d’une luminosité de 20 %, le connecteur supporte jusqu’à 200
LED.
Avant d’installer ou de retirer le ruban LED, veillez à toujours éteindre l’alimenta-
tion et à débrancher le câble d’alimentation de la prise électrique.
Veuillez utiliser un logiciel MSI dédié pour contrôler le ruban d’extension LED.
11 +5V 2 Data
3 No Pin 4 Ground
23
Ces LEDs indiquent l’état de débogage de la carte mère.
Le connecteur JRGB vous permet de connecter un ruban LED RGB de type 5050 12 V.
Le connecteur JRGB supporte des rubans LED RGB (12 V/G/R/B) de type 5050 d’une
longueur de 2 mètres maximum avec une puissance nominale maximale de 3 A (12 V).
Avant d’installer ou de retirer le ruban LED RGB, veillez à toujours éteindre l’ali-
mentation et à débrancher le câble d’alimentation de la prise électrique.
Veuillez utiliser un logiciel MSI dédié pour contrôler le ruban d’extension LED.
11 +12V 2 G
3 R 4 B
— indique que le CPU n’est pas détecté ou que son initialisation a échoué.
— indique que la mémoire DRAM n’est pas détectée ou que son initialisation
a échoué.
— indique que le GPU n’est pas détecté ou que son initialisation a échoué.
— indique que le périphérique de démarrage n’est pas détecté ou que son
initialisation a échoué.
Veuillez vous référer au site www.msi.com pour télécharger et mettre à jour les
derniers utilitaires et pilotes.
Allumez l’ordinateur.
Insérez le disque ou la clé USB d’installation de Windows® 10 dans votre
ordinateur.
Appuyez sur le bouton du boîtier de l’ordinateur.
Appuyez sur la touche pendant le POST (Power-On Self Test) du système
pour entrer dans le menu de démarrage.
Choisissez le disque ou la clé USB d’installation de Windows® 10 dans le menu de
démarrage.
Appuyez sur n’importe quelle touche lorsqu’apparaît le message
.
Suivez les instructions à l’écran pour installer Windows® 10.
24
Allumez l’ordinateur sous Windows® 10.
Insérez MSI® Drive Disc dans le lecteur optique.
Cliquez sur la fenêtre popup
, puis choisissez
pour ouvrir l’outil d’installation. Si vous désactivez la fonction
AutoPlay dans le panneau de configuration Windows, vous pouvez quand même
exécuter manuellement à partir du chemin d’accès depuis la
racine du disque de pilotes MSI.
L’outil d’installation trouvera et listera tous les pilotes dont vous avez besoin
dans l’onglet .
Cliquez sur le bouton dans le coin inférieur droit de la fenêtre.
L’installation des pilotes commence. Une fois terminée, il vous sera demandé de
redémarrer.
Cliquez sur le bouton pour terminer.
Redémarrez votre ordinateur.
MSI Center est une application qui vous aide à optimiser facilement les paramètres
de jeu et à utiliser les logiciels de création de contenu de manière intuitive. Elle vous
permet également de contrôler et de synchroniser les effets de lumière LED sur les
PC et autres produits MSI. Avec MSI Center, vous pouvez personnaliser les modes
selon vos envies, surveiller les performances du système et régler la vitesse du
ventilateur.
Si vous souhaitez en savoir plus sur MSI Center, veuillez vous
référer au fichier
http://download.msi.com/manual/mb/MSICENTER.pdf
ou scannez le code QR pour y accéder.
Les fonctions peuvent varier en fonction du produit que vous possédez.
25
Le BIOS UEFI de MSI est compatible avec l’architecture UEFI (Unified Extensible
Firmware Interface). Le BIOS UEFI présente de nombreuses nouvelles
fonctionnalités et avantages qui ne sont pas proposés par le BIOS traditionnel. Le
BIOS UEFI est ainsi voué à totalement remplacer le BIOS traditionnel à l’avenir. Le
BIOS UEFI de MSI utilise UEFI comme mode de démarrage par défaut pour profiter
au maximum des capacités du nouveau chipset.
Dans ce guide d’utilisation, le terme BIOS se réfère au BIOS UEFI, sauf indication
contraire.
Démarrage rapide — L’UEFI peut démarrer directement le système d’exploitation
et enregistrer le processus d’autotest du BIOS. Il élimine également le temps à
attendre pour passer en mode CSM pendant le POST.
Prend en charge des partitions de disque dur supérieures à 2 To.
Prend en charge plus de 4 partitions principales avec une table de partition GUID
(GPT).
Prend en charge un nombre illimité de partitions.
Prend en charge toutes les capacités de nouveaux appareils — les nouveaux
appareils peuvent ne pas fournir de compatibilité descendante.
Prend en charge le démarrage sécurisé — L’UEFI peut vérifier la validité du
système d’exploitation pour s’assurer qu’aucun malware ne perturbe le processus
de démarrage.
— cette carte mère supporte uniquement
le système d’exploitation Windows 10 64 bits.
— le système détectera votre carte graphique. Un
message d’avertissement apparaît si
.
Nous vous recommandons de remplacer votre carte graphique par un modèle
compatible GOP/UEFI ou d’utiliser la puce graphique intégrée à votre processeur
pour profiter d’un fonctionnement normal.
Allumez votre ordinateur.
Pendant le démarrage, lorsqu’apparaît le message
sur l’écran, veuillez appuyer sur la touche .
Après être entré dans le BIOS, vous pouvez vérifier le en haut de
l’écran.
26
Les réglages par défaut fournissent une performance optimale pour la stabilité du
système en conditions normales. Veillez à
pour éviter d’endommager le système ou tout problème au démarrage, sauf si vous
êtes familier avec le BIOS.
—
n’est donc donnée qu’à titre de référence. Vous pouvez aussi vous référer à l’onglet
pour obtenir la description des fonctions du BIOS.
Les écrans, les options et les paramètres du BIOS peuvent varier selon votre
système.
Pendant le démarrage, lorsqu’apparaît le message
sur l’écran, veuillez appuyer sur la touche .
: Liste d’aide générale
: Ajouter ou supprimer un élément favori
: Entrer dans le menu Favoris
: Entrer dans le menu de caractéristiques du processeur
: Entrer dans le menu Memory-Z
: Charger les réglages par défaut
: Alterner entre le mode avancé et le mode simplifié
: Charger le profil d’overclocking
: Sauvegarder le profil d’overclocking
: Sauvegarder les modifications et réglages*
: Prendre une capture d’écran et la conserver dans la clé USB (au format FAT/
FAT32 uniquement)
: Entrer dans la page de recherche
* Lorsque vous appuyez sur F10, une fenêtre de confirmation apparaît et fournit
l’information de modification. Choisissez entre Oui et Non pour confirmer.
Si vous souhaitez en savoir plus sur la configuration du BIOS,
veuillez vous référer au fichier
http://download.msi.com/manual/mb/Intel500BIOSfr.pdf
ou scannez le code QR pour y accéder.
27
Il se peut que vous ayez besoin de récupérer les réglages BIOS par défaut pour
résoudre des problèmes. Pour réinitialiser les réglages du BIOS, veuillez suivre l’une
des méthodes suivantes :
Allez dans le Setup du BIOS et appuyez sur pour charger les réglages par
défaut.
Court-circuitez le cavalier Clear CMOS sur la carte mère.
Appuyez sur le bouton Clear CMOS sur le panneau arrière Entrée/Sortie.
Assurez-vous que l’ordinateur est éteint avant d’effacer les données CMOS. Veuillez
vous référer à la section cavalier/bouton Clear CMOS pour en savoir plus sur la
réinitialisation du BIOS.
Avant la mise à jour :
Veuillez télécharger la dernière version de BIOS compatible à votre carte mère sur le
site MSI. Ensuite, veuillez sauvegarder le nouveau BIOS sur la clé USB.
Mettre le BIOS à jour :
Connectez la clé USB contenant le profil au port USB.
Veuillez vous référer aux méthodes suivantes pour passer en mode flash.
Redémarrez et appuyez sur la touche pendant le processus de POST
et cliquez sur pour redémarrer le système.
Redémarrez et appuyez sur la touche pendant le processus de POST pour
entrer dans l’interface du BIOS. Cliquez le bouton et cliquez sur
pour redémarrer le système.
Choisissez un profil BIOS pour commencer la mise à jour du BIOS.
Lorsque vous y êtes invité, cliquez sur pour lancer la restauration du
BIOS.
Une fois la mise à jour terminée, le système redémarrera automatiquement.
28
Avant la mise à jour :
Assurez-vous que le lecteur LAN est bien installé et que l’ordinateur est
correctement connecté à internet.
Veuillez désactiver tous les autres logiciels d’application avant de mettre à jour le
BIOS.
Mettre le BIOS à jour :
Installez et lancez MSI CENTER et accédez à la page .
Choisissez et cliquez sur le bouton .
Choisissez le profil BIOS et cliquez sur le bouton .
Le rappel d’installation apparaît. Cliquez ensuite sur le bouton .
Le système redémarrera automatiquement pour la mise à jour du BIOS.
Une fois la mise à jour terminée, le système redémarrera automatiquement.
Veuillez télécharger la dernière version du BIOS compatible à votre carte mère
sur le site MSI®.
Renommez le BIOS en . Ensuite, veuillez sauvegarder le profil MSI.ROM
sur le répertoire racine de la clé USB.
Connectez l’alimentation aux connecteurs et . (Pas
besoin d’installer le processeur et la mémoire.)
Branchez la clé USB contenant le fichier MSI.ROM au situé sur
le panneau arrière Entrée/Sortie.
Appuyez sur le bouton pour activer le BIOS, et le bouton LED
commence à clignoter.
Une fois le processus terminé, la LED s’éteint.
1
3
4
10
LAN Port LED Zustandstabelle ……………………………………………………………………..10
Konfiguration der Audioanschlüsse ……………………………………………………………….10
11
CPU Sockel …………………………………………………………………………………………………12
DIMM-Steckplätze ……………………………………………………………………………………….13
PCI_E1~4: PCIe Erweiterungssteckplätze ………………………………………………………14
JFP1, JFP2: Frontpanel-Anschlüsse ……………………………………………………………..15
JAUD1: Audioanschluss des Frontpanels ……………………………………………………….15
SATA1~6: SATA 6Gb/s Anschlüsse …………………………………………………………………16
M2_1~3: M.2 Steckplätze (Key M) ………………………………………………………………….16
ATX_PWR1, CPU_PWR1~2, PCIE_PWR1:
Stromanschlüsse ………………………………..17
JUSB1~2: USB 2.0 Anschlüsse ………………………………………………………………………18
JUSB3~4: USB 3.2 Gen 1 5Gbit/s Anschlüsse ………………………………………………….18
JUSB1: USB 3.2 Gen 2 Typ-C Anschluss …………………………………………………………19
JTBT1: Anschluss für Thunderbolt-Erweiterungskarte ……………………………………19
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Stromanschlüsse für Lüfter ………………20
JTPM1: TPM Anschluss ………………………………………………………………………………..20
JCI1: Gehäusekontaktanschluss ……………………………………………………………………21
JCOM1: Serieller Anschluss ………………………………………………………………………….21
JDASH1: Tuning Controller-Anschluss ………………………………………………………….21
JBAT1: Clear CMOS Steckbrücke (Reset BIOS) ……………………………………………….22
JRAINBOW1~2: Adressierbare RGB LED Anschlüsse ………………………………………22
JRGB1: RGB LED Anschluss …………………………………………………………………………23
EZ Debug LED ……………………………………………………………………………………………..23
24
Installation von Windows® 10 ………………………………………………………………………..24
Installation von Treibern ………………………………………………………………………………24
MSI Center ………………………………………………………………………………………………….24
Danke, dass Sie sich für das MSI®
Motherboard entschieden haben. Dieses Handbuch
gibt informationen über Motherboard-Layout, Komponen-
tenübersicht, BIOS-Setup und Softwareinstallation.
2
25
BIOS Setup ………………………………………………………………………………………………….26
Öffnen des BIOS Setups ……………………………………………………………………………….26
BIOS-Benutzerhandbuch ……………………………………………………………………………..26
Reset des BIOS ……………………………………………………………………………………………27
Aktualisierung des BIOS……………………………………………………………………………….27
3
Die im Paket enthaltene Komponenten sind der Beschädigung durch
elektrostatischen Entladung (ESD). Beachten Sie bitte die folgenden Hinweise, um
die erfolgreichen Computermontage sicherzustellen.
Stellen Sie sicher, dass alle Komponenten fest angeschlossen sind. Lockere
Steckverbindungen können Probleme verursachen, zum Beispiel: Der Computer
erkennt eine Komponente nicht oder startet nicht.
Halten Sie das Motherboard nur an den Rändern fest, und verhindern Sie die
Berührung der sensiblen Komponenten.
Um eine Beschädigung der Komponenten durch elektrostatische Entladung
(ESD) zu vermeiden, sollten Sie eines elektrostatischen Armbands während
der Handhabung des Motherboards tragen. Wenn kein elektrostatischen
Handgelenkband vorhanden ist, sollten Sie Ihre statische Elektrizität ableiten, indem
Sie ein anderes Metallobjekt berühren, bevor Sie das Motherboard anfassen.
Bewahren Sie das Motherboard in einer elektrostatische Abschirmung oder einem
Antistatiktuch auf, wenn das Motherboard nicht installiert ist.
Überprüfen Sie vor dem Einschalten des Computers, dass sich keine losen
Schrauben und andere Bauteile auf dem Motherboard oder im Computergehäuse
befinden.
Bitte starten Sie den Computer nicht, bevor die Installation abgeschlossen ist.
Dies könnte permanente Schäden an den Komponenten sowie zu das Verletzung des
Benutzers verursachen.
Sollten Sie Hilfe bei der Installation benötigen, wenden Sie sich bitte an einen
zertifizierten Computer-Techniker.
Schalten Sie die Stromversorgung aus und ziehen Sie das das Stromkabel ab,
bevor Sie jegliche Computer-Komponente ein- und ausbauen.
Bewahren Sie die Bedienungsanleitung als künftige Referenz auf.
Halten Sie das Motherboard von Feuchtigkeit fern.
Bitte stellen Sie sicher, dass Ihre Netzspannung den Hinweisen auf dem Netzteil
vor Anschluss des Netzteils an die Steckdose entspricht.
Verlegen Sie das Netzkabel so, dass niemand versehentlich darauf treten kann.
Stellen Sie nichts auf dem Netzkabel ab.
Alle Achtungs- und Warnhinweise auf dem Motherboard müssen befolgt werden.
Falls einer der folgenden Umstände eintritt, lassen Sie bitte das Motherboard von
Kundendienstpersonal prüfen:
Flüssigkeit ist in dem Computer eingedrungen.
Das Motherboard wurde Feuchtigkeit ausgesetzt.
Das Motherboard funktioniert nicht richtig oder Sie können es nicht wie in der
Bedienungsanleitung beschrieben bedienen.
Das Motherboard ist heruntergefallen und beschädigt.
Das Motherboard weist offensichtlich Zeichen eines Schadens auf.
Nutzen und lagern Sie das Gerät nicht an Stellen, an denen Temperaturen von
mehr als 60°C herrschen — das Motherboard kann in diesem Fall Schaden nehmen.
4
Unterstützt Intel® Core™ der 10. Generation Prozessoren,
Intel® Core™ der 11. Generation Prozessoren, Pentium® Gold
und Celeron® Prozessoren*
Prozessor Sockel LGA1200
* Weitere Kompatibilitätsinformationen finden Sie unter www.
intel.com
Intel® Z590 Chipsatz
4x DDR4 Speicherplätze, aufrüstbar bis 128 GB*
Unterstützt 1R 2133/ 2666/ 2933 MHz für 10. Gen Intel® CPU
(durch JEDEC & POR)
Unterstützt 1R 2133/ 2666/ 2933/ 3200 MHz für 11. Gen Intel®
CPU (durch JEDEC & POR)
Maximale Übertaktfrequenz:
1DPC 1R max. Übertragungsraten bis zu 5333 MHz
1DPC 2R max. Übertragungsraten bis zu 4700+ MHz
2DPC 1R max. Übertragungsraten bis zu 4400+ MHz
2DPC 2R max. Übertragungsraten bis zu 4000+ MHz
Dual-Kanal-Speicherarchitektur
Unterstützt non-ECC, ungepufferte Speicher
Unterstützt Intel® Extreme Memory Profile (XMP)
* Weitere Informationen zu kompatiblen Speicher finden Sie
unter: http://www.msi.com
2x PCIe x16 Steckplätze
Unterstützt x16/ x4
PCI_E1 (von CPU)
Unterstützt bis zu PCIe 4.0 für 11. Gen Intel® CPU
Unterstützt bis zu PCIe 3.0 für 10. Gen Intel® CPU
PCI_E3 (von Z590 Chipsatz)
Unterstützt bis zu PCIe 3.0
2x PCIe 3.0 x1 Steckplätze (von Z590 Chipsatz)
Realtek® ALC897 Codec
7.1-Kanal-HD-Audio
Unterstützt die 2-Wege AMD® CrossFire™ Technologie
Fortsetzung auf der nächsten Seite
5
Fortsetzung der vorherigen Seite
1x HDMI 2.0b mit HDR Anschluss, Unterstützung einer
maximalen Auflösung von 4K 60Hz */**
1x DisplayPort 1.4 Anschluss, Unterstützung einer
maximalen Auflösung von 4K 60Hz */**
* Es ist verfügbar für den Prozessor mit integrierter Grafik.
** Die Grafikkarten-Spezifikationen können abhängig von der
installierten CPU variieren.
1x Intel® I225-V 2.5Gbit/s LAN Controller
Intel® Wi-Fi 6E AX210
Das Wireless-Modul ist im M.2 (Key-E Steckplatz
vorinstalliert
Unterstützt MU-MIMO TX/RX, 2,4GHz/ 6GHz (160MHz) mit
Datenraten bis zu 2,4Gbit/s
Unterstützt 802.11 a/ b/ g/ n/ ac/ ax
Unterstützt Bluetooth® 5.2, FIPS, FISMA
6x SATA 6Gb/s Anschlüsse (von Z590 Chipsatz)
3x M.2 Steckplätze (Key M)
M2_1 Steckplatz (von CPU)*
Nur unter 11. Gen Intel® CPU verfügbar
Unterstützt bis zu PCIe 4.0 x4
Unterstützt 2242/ 2260/ 2280/ 22110 Speichergeräte
M2_2*, M2_3** Steckplatz (von Z590 Chipsatz)
Unterstützt bis zu PCIe 3.0 x4
Unterstützt SATA bis zu 6Gb/s
Unterstützt 2242/ 2260/ 2280 Speichergeräte
Intel® Optane™ Memory Ready***
Unterstützt Intel® Smart Response Technologie für Intel
Core™ Prozessoren
* SATA2 wird nicht zur Verfügung stehen, wenn Sie eine M.2
SATA SSD im M2_2 Steckplatz installieren.
** SATA5 & SATA6 werden nicht zur Verfügung stehen, wenn
Sie eine M.2 SSD im M2_3 Steckplatz installieren.
*** Bevor Sie Intel® Optane™ Speichermodule verwenden,
stellen Sie bitte über Downloads von der MSI Website sicher,
dass die Treiber und das BIOS auf dem neuesten Stand sind.
Unterstützt RAID 0, RAID 1 und RAID 10 für SATA
Speichergeräte
Unterstützt RAID 0 und RAID 1 für M.2 NVMe Speichergeräte
Fortsetzung auf der nächsten Seite
6
Fortsetzung der vorherigen Seite
Intel® Z590 Chipsatz
1x USB3.2 Gen2x2 20Gbit/s Anschluss (Typ-C Anschluss
an der rückseitigen Anschlussleiste)
2x USB 3.2 Gen 2 10Gbit/s Anschlüsse (1 Typ-C interner
Anschluss und 1 Typ-A Anschluss an der rückseitigen
Anschlussleiste)
6x USB 3.2 Gen 1 5Gbit/s Anschlüsse (2 Typ-A
Anschlüsse an der rückseitigen Anschlussleiste, und
4 Anschlüsse stehen durch die internen USB 3.2 Gen 1
5Gbit/s Anschlüsse zur Verfügung)
USB 2.0 Hubs GL850G
4x USB 2.0 Typ-A Anschlüsse an der rückseitigen
Anschlussleiste
4x USB 2.0 Anschlüsse stehen durch die internen USB
2.0 Anschlüsse zur Verfügung
1x 24-poliger ATX Stromanschluss
1x 8-poliger ATX 12V Stromanschluss
1x 4-poliger ATX 12V Stromanschluss
1x 6-poliger ATX PCIe Stromanschluss
6x SATA 6Gb/s Anschlüsse
3x M.2 Steckplätze (M-Key)
1x USB 3.2 Gen 2 10Gbit/s Typ-C Anschluss
2x USB 3.2 Gen 1 5Gbit/s Anschlüsse (unterstützt
zusätzliche 4 USB 3.2 Gen 1 5Gbit/s Anschlüsse)
2x USB 2.0 Anschlüsse (unterstützt zusätzliche 4 USB 2.0
Anschlüsse)
1x 4-poliger CPU-Lüfter-Anschluss
1x 4-poliger Anschluss für die Wasserpumpe
6x 4-polige System-Lüfter-Anschlüsse
1x Audioanschluss des Frontpanels
2x System-Panel-Anschlüsse
1x Gehäusekontaktschalter
1x Clear CMOS Steckbrücke
1x TPM Anschluss
1x Serieller Anschluss
1x Tuning Controller Anschluss
1x TBT Anschluss (unterstützt RTD3)
Fortsetzung auf der nächsten Seite
7
Fortsetzung der vorherigen Seite
1x 4-poliger RGB LED Anschluss
2x 3-polige RAINBOW LED Anschlüsse
4x EZ Debug LED
1x Flash BIOS Taste
1x PS/2 Tastatur/ Maus-Combo-Anschluss
4x USB 2.0 Typ-A Anschlüsse
1x DisplayPort
1x HDMI Anschluss
1x LAN (RJ45) Anschluss
2x USB 3.2 Gen 1 5Gbit/s Typ-A Anschlüsse
1x USB 3.2 Gen 2 10Gbit/s Typ-A Anschluss
1x USB 3.2 Gen 2×2 20Gbit/s Typ-C Anschluss
2x Wi-Fi Antennenanschlüsse (nur für Z590 PRO WIFI)
6x Audiobuchsen
NUVOTON NCT6687-R Controller Chip
CPU/System/Chipsatz Temperaturerfassung
CPU/ System/ Pump-Lüfter Geschwindigkeitserfassung
CPU/ System/ Pump-Lüfter Drehzahlregelung
ATX Formfaktor
12 Zoll x 9,6 Zoll (30,5 cm x 24,4 cm)
1x 256 Mb Flash
UEFI AMI BIOS
ACPI 6.2, SMBIOS 3.0
Mehrsprachenunterstützung
Treiber
MSI Center
Intel® Extreme Tuning Utility
CPU-Z MSI GAMING
Google Chrome™, Google Toolbar, Google Drive
Norton™ Internet Security Solution
Fortsetzung auf der nächsten Seite
8
Fortsetzung der vorherigen Seite
Mystic Light
LAN Manager
Benutzer-Scenario
Hardware Monitor
Frozr AI Kühlung
True Color
Live Update
Speed Up
Smart Tool
Super Charger
Audio
Audio Boost
Netzwerk
2.5G LAN
LAN Manager
Intel WiFi (Z590 PRO WIFI)
Kühlung
Extended Heatsink Design
M.2 Shield Frozr
K7 Thermal-Pad
Choke-Pad
Pump-Lüfter
Smart-Lüftersteuerung
LED
Mystic Light Extension (RAINBOW/RGB)
Mystic Light SYNC
EZ LED Steuerung
EZ DEBUG LED
Fortsetzung auf der nächsten Seite
9
Fortsetzung der vorherigen Seite
Leistung
Lightning Gen 4 PCI-E Steckplatz
Lightning Gen 4 M.2
Multi GPU-CrossFire Technologie
DDR4 Boost
Core Boost
Lightning USB 20G
USB 3.2 Gen 2 10G
USB Anschluss mit Typ A+C
Front USB Typ-C
Dual CPU Power
Zusätzlicher PCIE-Stromanschluss
2oz Kupfer verdicktes PCB
Schutz
PCI-E Steel Armor
Erfahrung
MSI Center
Frozr AI Kühlung
Click BIOS 5
Flash BIOS Taste
10
Aus No link
Gelb Linked
Blinkt Data activity
Aus 10 Mbit/s Verbindung
Grün 100/ 1000 Mbit/s Verbindung
Orange 2,5 Gbit/s Verbindung
USB 3.2 Gen 1
5Gbit/s Typ-A
Flash BIOS Taste
PS/2 Combo port 2.5 Gbit/s LAN
DisplayPort
USB 2.0 Type-A
USB 2.0 Typ-A Audioanschlüsse
Wi-Fi Antennenanschlüsse
(Nur für Z590 PRO WIFI)
USB 3.2 Gen 2×2
20Gbit/s Typ-C USB 3.2 Gen 2
10Gbit/s Typ-A
Flash BIOS
Anschluss
2468
Line-Out/ Vorderer
Lautsprecher
Line-In
Hinterer Lautsprecher
Mitte-/ Subwoofer-Ausgang
Seitliche Lautsprecher
Mic In
Verbindet, : Leer)
11
* Abstand zwischen der Mitte der CPU und dem nächsten DIMM-Steckplatz.
SATA6
SATA5
SYS_FAN5
SYS_FAN4
JCOM1
JTBT1
JFP2
JTPM1
JRGB1
JCI1
M2_3
M2_2
M2_1
SYS_FAN1
JUSB4
JUSB5
JUSB3
JUSB1
JUSB2
PCIE_PWR1
SYS_FAN3
SYS_FAN2
CPU_FAN1
SYS_FAN6
PUMP_FAN1
PCI_E1
PCI_E2
PCI_E3
JBAT1
PCI_E4
JDASH1
Prozessor Sockel
CPU_PWR1
CPU_PWR2
JRAINBOW2
JAUD1
JRAINBOW1
JFP1
ATX_PWR1
DIMMB1
DIMMB2
DIMMA1
DIMMA2
50.77mm*
12
Installieren Sie bitte die CPU in den CPU Sockel, wie unten aufgezeigt.
Ziehen Sie das Netzkabel ab, bevor Sie die CPU ein- und ausbauen.
Bitte bewahren Sie die CPU Schutzkappe nach der Installation des Prozessors auf.
MSI wird RMA (Return Merchandise Authorization) Anfragen nur dann behandeln,
wenn die Schutzklappe auf dem CPU-Sockel des Motherboards sitzt.
Wenn Sie die CPU einbauen, denken sie bitte daran einen CPU-Kühler zu installie-
ren. Ein CPU-Kühlkörper ist notwendig, um eine Überhitzung zu vermeiden und die
Systemstabilität beizubehalten.
Stellen Sie sicher, dass Ihr Kühlkörper eine feste Verbindung mit der CPU herg-
estellt hat, bevor Sie Ihr System starten.
Überhitzung beschädigt die CPU und das System nachhaltig. Stellen Sie stets eine
korrekte Funktionsweise des CPU Kühlers sicher, um die CPU vor Überhitzung zu
schützen. Stellen Sie sicher, dass eine gleichmäßige Schicht thermischer Paste oder
thermischen Tapes zwischen der CPU und dem Kühlkörper vorhanden ist, um die
Wärmeableitung zu erhöhen.
Schützen Sie den CPU-Sockel immer mit der Plastikabdeckung, wenn keine CPU
installiert ist.
Verwenden Sie bitte die Installationsanweisung des Kühlkörpers/Kühlers, falls Sie
eine seperate CPU oder einen Kühlkörper/ Kühler erworben haben.
1
4
6
5
78
9
3
2
13
DIMMB2
DIMMA2 DIMMA2
Setzen Sie bitte ein Speichermodul wie untern gezeigt in den DIMM-Steckplatz ein.
DIMMB2
DIMMB1
DIMMA2
DIMMA1
1
1
2
3
3
2
14
Um einen sicheren Systemstart zu gewährleisten, bestücken Sie immer
zuerst.
Stellen Sie im Dual-Kanal-Modus bitte sicher, dass Sie Module des gleichen
Typs und identischer Speicherdichte in den DIMM Slots unterschiedlicher Kanäle
verwenden.
Einige Speichermodule können beim Übertakten auf einer niedrigeren Frequenz
arbeiten, als der festgelegte Wert — abhängig von dem SPD (Serial Presence Detect).
Stellen Sie im BIOS-Setup mit DRAM Frequency die Speicherfrequenz ein, wenn Sie
mit der festgelegten oder einer höheren Speicherfrequenz arbeiten möchten.
des DIMMs oder beim Übertakten zu verwenden.
Die Stabilität und Kompatibilität beim Übertakten der installierten Speichermodule
sind abhängig von der installierten CPU und den installierten Geräten.
http://www.msi.com.
Achten Sie darauf, dass Sie den Strom abschalten und das Netzkabel aus der
Steckdose herausziehen, bevor Sie eine Erweiterungskarte installieren oder ent—
fernen. Lesen Sie bitte auch die Dokumentation der Erweiterungskarte, um notwen-
dige zusätzliche Hardware oder Software-Änderungen zu überprüfen.
der das Gewicht trägt und eine
Verformung des Steckplatzes vermeidet.
Für die Installation einer einzelnen PCIe x16 Erweiterungskarte mit optimaler
Leistung, empfehlen wir den Steckplatz zu verwenden.
: PCIe 4.0/ 3.0 x16 (von CPU)
: PCIe 3.0 x4 (von Z590 Chipsatz)
: PCIe 3.0 x1 (von Z590 Chipsatz)
: PCIe 3.0 x1 (von Z590 Chipsatz)
15
Diese Anschlüsse verbinden die Schalter und LEDs des Frontpanels.
1
2 10
9
+
+
+— ——
—
+
Power LED
HDD LED Reset Switch
Reserved
Power Switch 1 HDD LED + 2 Power LED +
3 HDD LED — 4 Power LED —
5 Reset Switch 6 Power Switch
7 Reset Switch 8 Power Switch
9 Reserved 10 No Pin
JFP2 1
+
+—
—
Speaker
Buzzer 1 Speaker — 2 Buzzer +
3 Buzzer — 4 Speaker +
HDD LED
RESET SW
HDD LED HDD LED —
HDD LED +
POWER LED —
POWER LED +
POWER LED
JFP1
Dieser Anschluss ermöglicht den Anschluss von Audiobuchsen eines Frontpanels.
1
2 10
9
1 MIC L 2 Ground
3 MIC R 4 NC
5 Head Phone R 6 MIC Detection
7 SENSE_SEND 8 No Pin
9 Head Phone L 10 Head Phone Detection
16
Diese Anschlüsse basieren auf der Hochgeschwindigkeitsschnittstelle SATA 6Gb/s.
Pro Anschluss kann ein SATA Gerät angeschlossen werden.
SATA1
SATA3
SATA2
SATA6
SATA5
SATA4
SATA2 wird nicht zur Verfügung stehen, wenn Sie eine M.2 SATA SSD im M2_2
Steckplatz installieren.
Die SATA5 und SATA6 Anschlüsse werden nicht zur Verfügung stehen, wenn Sie
eine M.2 SSD im M2_3 Steckplatz installieren.
Knicken Sie das SATA-Kabel nicht in einem 90° Winkel. Datenverlust könnte die
Folge sein.
SATA-Kabel haben identische Stecker an beiden Enden. Es wird empfohlen den
Bitte installieren Sie das M.2 Solid-State-Laufwerke (SSD) in den M.2 Steckplatz
(siehe unten).
1
3
Abstandshalter
Mitgelieferte
M.2-Schraube 30º30º
2
17
Mit diesen Anschlüssen verbinden Sie die ATX Stromstecker.
Stellen Sie sicher, dass alle Anschlüsse mit den richtigen Anschlüssen des Netzteils
verbunden sind, um einen stabilen Betrieb der Hauptplatine sicherzustellen.
24
131
12
ATX_PWR1
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 Ground 15 Ground
4 +5V 16 PS-ON#
5 Ground 17 Ground
6 +5V 18 Ground
7 Ground 19 Ground
8 PWR OK 20 Res
9 5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 Ground
3
2 1
4CPU_PWR2 1 Ground 3 +12V
2 Ground 8 +12V
5
41
8
CPU_PWR1
1 Ground 5 +12V
2 Ground 6 +12V
3 Ground 7 +12V
4 Ground 8 +12V
1 3
64
PCIE_PWR1
1 +12V 4 Ground
2 +12V 5 Ground
3 +12V 6 Ground
18
Mit diesen Anschlüssen können Sie die USB 3.2 Gen 1 5Gbit/s Anschlüsse auf dem
Frontpanel verbinden.
1
10 11
20
1 Power 11 USB2.0+
2 USB3_RX_DN 12 USB2.0-
3 USB3_RX_DP 13 Ground
4 Ground 14 USB3_TX_C_DP
5 USB3_TX_C_DN 15 USB3_TX_C_DN
6 USB3_TX_C_DP 16 Ground
7 Ground 17 USB3_RX_DP
8 USB2.0- 18 USB3_RX_DN
9 USB2.0+ 19 Power
10 Ground 20 No Pin
Bitte beachten Sie, dass Sie die mit „Stromführende Leitung“ und „Erdleitung“
bezeichneten Pins korrekt verbinden müssen, ansonsten kann es zu Schäden
kommen.
Mit diesen Anschlüsse können Sie die USB 2.0 Anschlüsse auf dem Frontpanel
verbinden.
Bitte beachten Sie, dass Sie die mit VCC (Stromführende Leitung) und Ground (Er-
dung) bezeichneten Pins korrekt verbinden müssen, ansonsten kann es zu Schäden
kommen.
Um ein iPad, iPhone und einen iPod über USB-Anschlüsse aufzuladen, installieren
Sie bitte die MSI® Center-Dienstprogramm.
1
2 10
9
1 VCC 2 VCC
3 USB0- 4 USB1-
5 USB0+ 6 USB1+
7 Ground 8 Ground
9 No Pin 10 NC
19
Mit diesem Anschluss können Sie den USB 3.2 Gen 2 Typ-C Anschluss auf dem
Frontpanel verbinden. Der Anschluss verfügt über ein besonders sicheres Design.
Wenn Sie das Kabel anschließen, müssen Sie es in der entsprechenden Ausrichtung
verbinden.
JUSB1
USB Typ-C Kabel
USB Typ-C Anschluss auf
dem Frontpanel
Mit diesem Anschluss können Sie eine Ein-/Ausgang der Thunderbolt-
Erweiterungskarte anschließen.
1
2 16
15
1 TBT_Force_PWR 2 TBT_S0IX_Entry_REQ
3 TBT_CIO_Plug_Event# 4 TBT_S0IX_Entry_ACK
5 SLP_S3#_TBT 6 TBT_PSON_Override_N
7 SLP_S5#_TBT 8 Net Name
9 Ground 10 SMBCLK_VSB
11 DG_PEWake 12 SMBDATA_VSB
13 TBT_RTD3_PWR_EN 14 Ground
15 TBT_Card_DET_R# 12 PD_IRQ#
20
Dieser Anschluss wird für das TPM Modul (Trusted Platform Module) verwendet.
Weitere Informationen über den Einsatz des optionalen TPM Modules entnehmen Sie
bitte dem TPM Plattform Handbuch.
Diese Anschlüsse können im PWM (Pulse Width Modulation) Modus
oder Spannungsmodus betrieben werden. Im PWM-Modus bieten die
Lüfteranschlüsse konstante 12V Ausgang und regeln die Lüftergeschwindigkeit
per Drehzahlsteuersignal. Im DC-Modus bestimmen die Lüfteranschlüsse die
Lüftergeschwindigkeit durch Ändern der Spannung.
Sie können unter die Lüfterdrehzahl ändern.
1
1 Ground 2 +12V
3 Sense 4 Speed Control Signal
CPU_FAN1 PWM-Modus 2A 24W
PUMP_FAN1 PWM-Modus 3A 36W
SYS_FAN1~6 DC-Modus 1A 12W
1
1 Ground 2 Voltage Control
3 Sense 4 NC
1
212
11
1 SPI Power 2 SPI Chip Select
3
Master In Slave Out
(SPI Data)
4
Master Out Slave In
(SPI Data)
5 Reserved 6 SPI Clock
7 Ground 8 SPI Reset
9 Reserved 10 No Pin
11 Reserved 12 Interrupt Request
21
Dieser Anschluss wird mit einem Kontaktschalter verbunden.
Normal
(Standardwert) Löse den Gehäuseeingriff
aus
Schließen Sie den -Anschluss am Gehäusekontakt-Schalter/ Sensor am
Gehäuse an.
Schließen Sie die Gehäuseabdeckung.
Gehen Sie zu .
Stellen Sie auf .
Drücken Sie zum Speichern und Beenden und drücken Sie dann die —
Taste, um Ja auszuwählen.
Bei eingeschaltetem Computer wird eine Warnmeldung auf dem Bildschirm
angezeigt, wenn die Gehäuseabdeckung wieder geöffnet wird.
Gehen Sie zu .
Stellen Sie auf Reset.
Drücken Sie zum Speichern und Beenden und drücken Sie dann die —
Taste, um Ja auszuwählen.
Mit diesem Anschluss können Sie das optionale serielle Schnittstelle mit dem
Einbausatze verbinden.
An diesem Anschluss wird ein optionales Tuning Controller-Modul angeschlossen.
1
2 10
9
1 DCD 2 SIN
3 SOUT 4 DTR
5 Ground 6 DSR
7 RTS 8 CTS
9 RI 10 No Pin
1
2 6
5
1 No pin 2 NC
3 MCU_SMB_SCL_M 4 MCU_SMB_SDA_M
5 VCC5 6 Ground
22
Der Onboard CMOS Speicher (RAM) wird durch eine externe Spannungsversorgung
durch eine Batterie auf dem Motherboard versorgt, um die Daten der
Systemkonfiguration zu speichern. Wenn Sie die Systemkonfiguration löschen
wollen, müssen Sie die Steckbrücke für kurze Zeit umsetzen.
Daten
beibehalten
(Standardwert)
CMOS-Daten
löschen/ Reset des
BIOS
Schalten Sie den Computer ab und ziehen Sie das Netzkabel ab.
Verwenden Sie eine Steckbrücke, um für 5-10 Sekunden kurzzuschließen.
Entfernen Sie die Steckbrücke von .
Stecken Sie das Kabel Ihres Computers in die Steckdose hinein und schalten Sie
den Computer ein.
JRAINBOW ermöglicht den Anschluss von WS2812B einzeln adressierbaren RGB-
LED-Streifen (5 V).
Schließen Sie nur passende LED-Streifen an. Der JRGB- und der JRAINBOW-
Anschluss verfügen über unterschiedliche Spannungen. Der Anschluss eines 5
V LED-Streifens an den JRGB-Anschluss führt zu einer Beschädigung des LED-
Streifens.
Der JRAINBOW Anschluss unterstützt bis zu 75 LEDs WS2812B einzeln adressier-
bare RGB-LED-Streifen (5 V/ Daten/ Erdung) mit der maximalen Leistung von 3 A (5
V). Bei einer Helligkeit von 20 Prozent unterstützt dieser Anschluss bis zu 200 LEDs.
Schalten Sie die Stromversorgung aus und ziehen Sie das Netzkabel ab, bevor Sie
die RGB-LED-Streifen ein- und ausbauen.
Bitte verwenden Sie die MSI-Software zur Steuerung des LED-Leuchtstreifens.
11 +5V 2 Data
3 No Pin 4 Ground
23
Diese LEDs zeigen den Status des Motherboards an.
— — CPU wird nicht erkannt oder ist fehlerhaft.
— DRAM wird nicht erkannt oder ist fehlerhaft.
— GPU wird nicht erkannt oder ist fehlerhaft.
— Boot-Gerät wird nicht erkannt oder ist fehlerhaft.
Mit dem JRGB Anschluss können Sie den 5050 RGB-LED-Streifen (12 V) anschließen.
Der JRGB Anschluss unterstützt bis zu 2 Metern 5050 RGB LED-Streifen (12V/G/
R/B) mit der maximalen Leistung von 3 A (12 V).
Schalten Sie die Stromversorgung aus und ziehen Sie das Netzkabel ab, bevor Sie
die RGB-LED-Streifen ein- und ausbauen.
Bitte verwenden Sie die MSI-Software zur Steuerung des LED-Leuchtstreifens.
11 +12V 2 G
3 R 4 B
24
Laden Sie die neuesten Treiber und Dienstprogramme von www.msi.com herunter
und aktualisieren Sie sie
Schalten Sie den Computer ein.
Legen Sie die Windows® 10 Disk oder das USB-Flashlaufwerk in das optisches
Laufwerk.
Drücken Sie die Taste auf dem Computergehäuse.
Drücken Sie die -Taste während des POST-Vorgangs (Power-On Self Test),
um das Bootmenu zu öffnen.
Wählen Sie das optische Laufwerk aus dem Bootmenu.
Wenn eine entsprechende Meldung
angezeigt wird, drücken Sie eine beliebige Taste.
Folgen Sie den Anweisungen auf dem Bildschirm, um das Dienstprogramm
„Windows® 10“ zu installieren.
Starten Sie Ihren Computer mit Windows® 10.
Legen Sie die MSI® Treiber Disk in das optische Laufwerk.
Klicken Sie auf die Pop-up-Meldung
und wählen Sie aus, um
den Installer zu öffnen. Wenn Sie die AutoPlay-Funktionen in der Windows-
Systemsteuerung ausschalten, können Sie das Programm im
Hauptverzeichnis der MSI Treiber CD auch manuell ausführen.
Der Installer wird findet eine Liste aller benötigten Treiber auf der
-Registerkarte.
Klicken Sie auf in der rechten unteren Ecke des Fensters.
Die Treiber-Installation läuft. Wenn die Installation abgeschlossen ist, werden Sie
dazu aufgefordet, den Computer neu zu starten.
Klicken Sie zum Beenden auf .
Starten Sie Ihren Computer neu.
MSI Center ist eine Anwendung, mit der Sie die Spieleinstellungen einfach
optimieren und die Software zur Erstellung von Inhalten einstellen können.
Außerdem können Sie LED-Lichteffekte in PCs und anderen MSI-Produkten
steuern und synchronisieren. Mit MSI Center können Sie ideale Modi einstellen, die
Systemleistung überwachen und die Lüftergeschwindigkeit anpassen.
Wenn Sie weitere Informationen zu MSI Center wünschen, besuchen
Sie bitte
http://download.msi.com/manual/mb/MSICENTER.pdf
oder scannen Sie den QR-Code.
Die Funktionen können je nach Produkt variieren.
25
Das MSI UEFI-BIOS ist mit der UEFI-Architektur (Unified Extensible Firmware
Interface) kompatibel. UEFI hat viele neue Funktionen und besitzt Vorteile, die das
traditionelle BIOS nicht bieten kann. UEFI wird das BIOS in Zukunft vollständig
ersetzen. Das MSI UEFI-BIOS verwendet UEFI als Standard-Startmodus, um die
Funktionen des neuen Chipsatzes voll auszunutzen.
Der Begriff „BIOS“ bezieht sich in diesem Benutzerhandbuch auf das UEFI-BIOS,
sofern nicht anders angegeben.
Schnelles Booten — UEFI kann das Betriebssystem direkt booten und den BIOS-
Selbsttestprozess speichern. Außerdem entfällt die Zeit, um während des POST in
den CSM-Modus zu wechseln.
Unterstützt Festplattenpartitionen, die größer als 2 TB sind.
Unterstützt mehr als 4 primäre Partitionen mit einer GUID-Partitionstabelle (GPT).
Unterstützt eine unbegrenzte Anzahl an Partitionen.
möglicherweise keine Abwärtskompatibilität.
überprüfen, um sicherzustellen, dass keine Malware den Startvorgang
beeinträchtigt.
— Dieses Motherboard unterstützt nur das
64-Bit-Windows 10-Betriebssystem.
Das System erkennt Ihre Grafikkarte. Bei Erkennung einer
nicht kompatiblen Grafikkarte wird die Warnmeldung
erkannt.
Wir empfehlen Ihnen, eine GOP / UEFI-kompatible Grafikkarte zu nutzen oder eine
CPU mit integrierter Grafikeinheit zu verwenden, um eine normale Funktion des
Systems zu gewährleisten.
Schalten Sie den Computer ein.
Während des BOOT-Vorgangs drücken Sie die Taste , wenn die Meldung
erscheint.
Nach dem Aufrufen des BIOS können Sie den oben auf dem
Bildschirm überprüfen.
26
Die Standardeinstellungen bieten die optimale Leistung für die Systemstabilität unter
Normalbedingungen. Sie sollten , um
mögliche Schäden des Systems oder Boot-Fehler zu vermeiden, außer Sie besitzen
ausreichende BIOS Kenntnisse.
BIOS Funktionen werden für eine bessere Systemleistung kontinuierlich aktualis-
iert. Deswegen können die Beschreibungen leicht von der letzten Fassung des BIOS
abweichen und sollten demnach nur als Anhaltspunkte dienen. Für eine Beschrei—
bung der BIOS Funktionen rufen Sie die Informationstafel aus.
Die BIOS-Bildschirme, -Optionen und -Einstellungen variieren je nach System.
Während des BOOT-Vorgangs drücken Sie die Taste , wenn die Meldung
erscheint.
: Allgemeine Hilfe
: Hinzufügen/Entfernen eines Favoritenpunkts
: Öffnen des Favoriten Menüs
: Öffnen des Menüs CPU-Spezifikationen
: Öffnen des Memory-Z Menüs
: Laden der ursprünglichen Setup-Standardwerte
: Wechselt zwischen dem Erweiterten-Modus und EZ-Modus
: OC-Profil wird vom USB-Stick geladen
: OC-Profil wird auf einem USB-Stick gespeichert
: Speichern oder Zurücksetzen der Änderungen*
: Macht einen Screenshot und speichert auf einen FAT/FAT32-USB-Laufwerk.
: Öffnet die Suchseite
* Beim Drücken der F10 Taste wird das Fenster zum Speichern der Einstellungen
angezeigt. Wählen Sie , um die Wahl zu bestätigen, oder , um die derzeitige
Einstellung beizubehalten.
Wenn Sie weitere Anweisungen zur BIOS-Einrichtung wünschen,
lesen Sie bitte
http://download.msi.com/manual/mb/Intel500BIOSde.pdf
oder scannen Sie den QR-Code.
27
Sie können die Werkseinstellung wieder herstellen, um bestimmte Probleme zu
lösen. Es gibt verschiedene Möglichkeiten, um das BIOS zurückzusetzen:
Öffnen Sie das BIOS und drücken Sie , um optimierten Einstellungen zu laden.
Schließen Sie die an das Motherboard an.
Drücken Sie die auf der Rückseite E/A des Panels.
Bitte lesen Sie für Informationen zum BIOS-Reset im Bereich
nach.
Vorbereitung:
Laden Sie bitte die neueste BIOS Version, die dem Motherboard-Modell entspricht,
Flash-Laufwerk.
BIOS-Aktualisierungsschritte:
Schließen das USB-Flashlaufwerk mit der BIOS-Datei an den Computer.
Bitte folgen Sie den nachfolgenden Schritten, um in den Blitz-Modus zu schalten.
Beim Neustart drücken Sie während des POST-Vorgangs die Taste
und klicken Sie auf tum das System neu zu starten.
Beim Neustart drücken Sie während des POST-Vorgangs die Taste
während des POST-Vorgangs die Taste. Klicken Sie die Taste und
klicken Sie auf tum das System neu zu starten.
Wählen Sie die BIOS-Datei zur Durchführung des BIOS-Aktualisierungsprozesses
aus.
Klicken Sie auf Ja, wenn Sie dazu aufgefordert werden, um die Wiederherstellung
des BIOS zu starten.
Nachdem das Flashen des BIOS vollständig ist, startet das System automatisch
neu.
28
Vorbereitung:
Stellen Sie sicher, dass zuvor die LAN-Treiber installiert wurden und eine
Internetverbindung eingerichtet ist.
Bitte schließen Sie jegliche andere Anwendungssoftware, bevor Sie das BIOS
aktualisieren.
Schritte zur Aktualisierung des BIOS:
Installieren und starten Sie „MSI DRAGON CENTER“ und gehen Sie zur —
Seite.
Wählen Sie aus und klicken Sie auf die Schaltfläche .
Wählen Sie die BIOS-Datei aus und klicken Sie auf das -Symbol.
Die Installationsanweisung wird angezeigt, klicken Sie daraufhin auf die
Schaltfläche Install.
Das System wird automatisch neu gestartet, um das BIOS zu aktualisieren.
Nachdem das Flashen des BIOS vollständig ist, startet das System automatisch
neu.
Laden Sie bitte die neueste BIOS Version, die das Modell des Motherboards
entspricht, von der offiziellen MSI® Website.
Benennen die BIOS-Datei im MSI.ROM um und speichern Sie die Datei im Root-
Verzeichnis des USB-Flash-Speichers.
Verbinden Sie die Stromversorgung an dem CPU_PWR1 und ATX_PWR1-Stecker.
(Sie benötigen keine CPU und keinen Speicher zu installieren)
Stecken Sie das USB-Flashlaufwerk, das die MSI.ROM-Datei enthält, in dem
Anschluss des Flash BIOS auf der Rückseite E/A des Panels ein.
Drücken Sie die Taste Flash BIOS, um das BIOS zu flashen, nun beginnt die Flash
BIOS LED zu blinken.
Nachdem das Flashen des BIOS vollständig ist, erlischt die Flash BIOS LED.
1
3
4
10
…………………………………………………..10
……………………………………………………………………….10
11
…………………………………………………………………………………..12
……………………………………………………………………………………………….13
……………………………………………………………………………………………….13
……………………………………………………………..14
……………………………………………………….15
……………………………………………………….15
…………………………………………………………………….16
…………………………………………………………………..16
……………………………17
…………………………………………………………………………18
……………………………………………………….18
…………………………………………………………..19
………………………19
……………………20
………………………………………………………………………..20
………………………………………………………21
……………………………………………………21
……………………………………………………..21
…………………………………..22
………………………………………………..22
……………………………………………………………………………..23
………………………………………………………………………………23
24
……………………………………………………………………………….24
………………………………………………………………………………….24
MSI Center ………………………………………………………………………………………………….24
2
25
………………………………………………………………………………………….26
………………………………………………………………………………..26
……………………………………………………………………26
…………………………………………………………………………………………………27
………………………………………………………………………………………..27
3
4
Intel® Z590
Realtek® ALC897 Codec
5
/**
/**
6E AX210
6
USB 2.0
7
NUVOTON NCT6687-R
UEFI AMI BIOS
ACPI 6.2, SMBIOS 3.0
MSI Center
Intel® Extreme Tuning Utility
CPU-Z MSI GAMING
Google Chrome™, Google Toolbar, Google Drive
Norton™ Internet Security Solution
8
Mystic Light
LAN Manager
User Scenario
Hardware Monitor
Frozr AI Cooling
True Color
Live Update
Speed Up
Smart Tool
Super Charger
Audio Boost
2.5G LAN
LAN Manager
Intel WiFi (Z590 PRO WIFI)
Extended Heatsink Design
M.2 Shield Frozr
K7 thermal pad
Choke pad
Pump Fan
Smart Fan Control
Mystic Light Extension (RAINBOW/RGB)
Mystic Light SYNC
EZ LED Control
EZ DEBUG LED
9
Lightning Gen 4 PCI-E Slot
Lightning Gen 4 M.2
Multi GPU-CrossFire Technology
DDR4 Boost
Core Boost
Lightning USB 20G
USB 3.2 Gen 2 10G
Dual CPU Power
Supplemental PCIE Power Connector
2oz Copper thickened PCB
PCI-E Steel Armor
MSI Center
Frozr AI Cooling
Click BIOS 5
10
USB 3.2 Gen 1
BIOS
DisplayPort
USB 2.0 Type-A
USB 2.0 Type-A
USB 3.2 Gen 2×2
USB 3.2 Gen 2
BIOS
2468
(
11
SATA6
SATA5
SYS_FAN5
SYS_FAN4
JCOM1
JTBT1
JFP2
JTPM1
JRGB1
JCI1
M2_3
M2_2
M2_1
SYS_FAN1
JUSB4
JUSB5
JUSB3
JUSB1
JUSB2
PCIE_PWR1
SYS_FAN3
SYS_FAN2
CPU_FAN1
SYS_FAN6
PUMP_FAN1
PCI_E1
PCI_E2
PCI_E3
JBAT1
PCI_E4
JDASH1
CPU_PWR1
CPU_PWR2
JRAINBOW2
JAUD1
JRAINBOW1
JFP1
ATX_PWR1
DIMMB1
DIMMB2
DIMMA1
DIMMA2
12
1
4
6
5
78
9
3
2
13
DIMMB2
DIMMA2 DIMMA2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
1
1
2
3
3
2
14
.
.
15
1
2 10
9
+
+
+— ——
—
+
Power LED
HDD LED Reset Switch
Reserved
Power Switch 1 HDD LED + 2 Power LED +
3 HDD LED — 4 Power LED —
5 Reset Switch 6 Power Switch
7 Reset Switch 8 Power Switch
9 Reserved 10 No Pin
JFP2 1
+
+—
—
Speaker
Buzzer 1 Speaker — 2 Buzzer +
3 Buzzer — 4 Speaker +
HDD LED
RESET SW
HDD LED HDD LED —
HDD LED +
POWER LED —
POWER LED +
POWER LED
JFP1
1
2 10
9
1 MIC L 2 Ground
3 MIC R 4 NC
5 Head Phone R 6 MIC Detection
7 SENSE_SEND 8 No Pin
9 Head Phone L 10 Head Phone Detection
16
SATA1
SATA3
SATA2
SATA6
SATA5
SATA4
M2_3.
1
3
30º30º
2
17
24
131
12
ATX_PWR1
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 Ground 15 Ground
4 +5V 16 PS-ON#
5 Ground 17 Ground
6 +5V 18 Ground
7 Ground 19 Ground
8 PWR OK 20 Res
9 5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 Ground
3
2 1
4CPU_PWR2 1 Ground 3 +12V
2 Ground 8 +12V
5
41
8
CPU_PWR1
1 Ground 5 +12V
2 Ground 6 +12V
3 Ground 7 +12V
4 Ground 8 +12V
1 3
64
PCIE_PWR1
1 +12V 4 Ground
2 +12V 5 Ground
3 +12V 6 Ground
18
1
10 11
20
1 Power 11 USB2.0+
2 USB3_RX_DN 12 USB2.0-
3 USB3_RX_DP 13 Ground
4 Ground 14 USB3_TX_C_DP
5 USB3_TX_C_DN 15 USB3_TX_C_DN
6 USB3_TX_C_DP 16 Ground
7 Ground 17 USB3_RX_DP
8 USB2.0- 18 USB3_RX_DN
9 USB2.0+ 19 Power
10 Ground 20 No Pin
1
2 10
9
1 VCC 2 VCC
3 USB0- 4 USB1-
5 USB0+ 6 USB1+
7 Ground 8 Ground
9 No Pin 10 NC
19
JUSB1
1
2 16
15
1 TBT_Force_PWR 2 TBT_S0IX_Entry_REQ
3 TBT_CIO_Plug_Event# 4 TBT_S0IX_Entry_ACK
5 SLP_S3#_TBT 6 TBT_PSON_Override_N
7 SLP_S5#_TBT 8 Net Name
9 Ground 10 SMBCLK_VSB
11 DG_PEWake 12 SMBDATA_VSB
13 TBT_RTD3_PWR_EN 14 Ground
15 TBT_Card_DET_R# 12 PD_IRQ#
20
1
212
11
1 SPI Power 2 SPI Chip Select
3
Master In Slave Out
(SPI Data)
4
Master Out Slave In
(SPI Data)
5 Reserved 6 SPI Clock
7 Ground 8 SPI Reset
9 Reserved 10 No Pin
11 Reserved 12 Interrupt Request
1
1 Ground 2 +12V
3 Sense 4 Speed Control Signal
CPU_FAN1
PUMP_FAN1
SYS_FAN1~6
1
1 Ground 2 Voltage Control
3 Sense 4 NC
21
.
.
.
.
.
, Reset.
.
1
2 10
9
1 DCD 2 SIN
3 SOUT 4 DTR
5 Ground 6 DSR
7 RTS 8 CTS
9 RI 10 No Pin
1
2 6
5
1 No pin 2 NC
3 MCU_SMB_SCL_M 4 MCU_SMB_SDA_M
5 VCC5 6 Ground
22
.
11 +5V 2 Data
3 No Pin 4 Ground
23
11 +12V 2 G
3 R 4 B
24
Windows® 10.
MSI Drive disc.
.
http://download.msi.com/manual/mb/MSICENTER.pdf
25
».
26
.
http://download.msi.com/manual/mb/Intel500BIOSru.pdf
27
BIOS.
28
.
.
.
.
1
3
4
10
…………………………………………………………………………………..10
………………………………………………………………………………………………10
11
…………………………………………………………………………………………………….12
………………………………………………………………………………………………….13
……………………………………………………………………………..14
…………………………………………………………………………….15
…………………………………………………………………………………..15
…………………………………………………………………………..16
………………………………………………………………………………16
ATX_PWR1, CPU_PWR1~2, PCIE_PWR1:
…………………………………………….17
………………………………………………………………………………..18
……………………………………………………………..18
……………………………………………………………….19
……………………………………………………………………19
………………………………………….20
………………………………………………………………………………….20
……………………………………………………………………………….21
………………………………………………………………………………….21
……………………………………………………………………………..21
………………………………………………………………22
………………………………………………………………22
………………………………………………………………………………….23
………………………………………………………………………………………….23
24
………………………………………………………………………………………..24
…………………………………………………………………………………………………….24
MSI Center ………………………………………………………………………………………………….24
2
25
……………………………………………………………………………………………………26
…………………………………………………………………………………………….26
…………………………………………………………………………………………….26
……………………………………………………………………………………………………27
……………………………………………………………………………………………………27
3
4
Intel® Core™
*
Intel®
*
5
*/**
/**
Intel® Wi-Fi 6E AX210
2.4Gbps
M2_1
* M2_2 SATA2
**
10
6
1
2
6
4
USB 2.0 Hubs GL850G
4
4 USB 2.0
7
UEFI AMI BIOS
ACPI 6.2, SMBIOS 3.0
MSI Center
CPU-Z MSI GAMING
8
True Color
Live Update
2.5G LAN
Intel WiFi (Z590 PRO WIFI)
9
Lightning Gen 4 PCI-E Slot
Lightning Gen 4 M.2
USB 3.2 Gen 2 10G
MSI Center
10
USB 3.2 Gen 1
5Gbps Type-A
2.5 Gbps LAN
USB 2.0 Type-A
USB 2.0 Type-A
USB 3.2 Gen 2×2
20Gbps Type-C USB 3.2 Gen 2
10Gbps Type-A
2468
11
SATA6
SATA5
SYS_FAN5
SYS_FAN4
JCOM1
JTBT1
JFP2
JTPM1
JRGB1
JCI1
M2_3
M2_2
M2_1
SYS_FAN1
JUSB4
JUSB5
JUSB3
JUSB1
JUSB2
PCIE_PWR1
SYS_FAN3
SYS_FAN2
CPU_FAN1
SYS_FAN6
PUMP_FAN1
PCI_E1
PCI_E2
PCI_E3
JBAT1
PCI_E4
JDASH1
CPU_PWR1
CPU_PWR2
JRAINBOW2
JAUD1
JRAINBOW1
JFP1
ATX_PWR1
DIMMB1
DIMMB2
DIMMA1
DIMMA2
12
1
4
6
5
78
9
3
2
13
DIMMB2
DIMMA2 DIMMA2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
1
1
2
3
3
2
14
15
1
2 10
9
+
+
+— ——
—
+
Power LED
HDD LED Reset Switch
Reserved
Power Switch 1 HDD LED + 2 Power LED +
3 HDD LED — 4 Power LED —
5 Reset Switch 6 Power Switch
7 Reset Switch 8 Power Switch
9 Reserved 10 No Pin
JFP2 1
+
+—
—
Speaker
Buzzer 1 Speaker — 2 Buzzer +
3 Buzzer — 4 Speaker +
HDD LED
RESET SW
HDD LED HDD LED —
HDD LED +
POWER LED —
POWER LED +
POWER LED
JFP1
1
2 10
9
1 MIC L 2 Ground
3 MIC R 4 NC
5 Head Phone R 6 MIC Detection
7 SENSE_SEND 8 No Pin
9 Head Phone L 10 Head Phone Detection
16
SATA1
SATA3
SATA2
SATA6
SATA5
SATA4
1
3
30º30º
2
17
24
131
12
ATX_PWR1
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 Ground 15 Ground
4 +5V 16 PS-ON#
5 Ground 17 Ground
6 +5V 18 Ground
7 Ground 19 Ground
8 PWR OK 20 Res
9 5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 Ground
3
2 1
4CPU_PWR2 1 Ground 3 +12V
2 Ground 8 +12V
5
41
8
CPU_PWR1
1 Ground 5 +12V
2 Ground 6 +12V
3 Ground 7 +12V
4 Ground 8 +12V
1 3
64
PCIE_PWR1
1 +12V 4 Ground
2 +12V 5 Ground
3 +12V 6 Ground
18
1
10 11
20
1 Power 11 USB2.0+
2 USB3_RX_DN 12 USB2.0-
3 USB3_RX_DP 13 Ground
4 Ground 14 USB3_TX_C_DP
5 USB3_TX_C_DN 15 USB3_TX_C_DN
6 USB3_TX_C_DP 16 Ground
7 Ground 17 USB3_RX_DP
8 USB2.0- 18 USB3_RX_DN
9 USB2.0+ 19 Power
10 Ground 20 No Pin
1
2 10
9
1 VCC 2 VCC
3 USB0- 4 USB1-
5 USB0+ 6 USB1+
7 Ground 8 Ground
9 No Pin 10 NC
19
JUSB1
1
2 16
15
1 TBT_Force_PWR 2 TBT_S0IX_Entry_REQ
3 TBT_CIO_Plug_Event# 4 TBT_S0IX_Entry_ACK
5 SLP_S3#_TBT 6 TBT_PSON_Override_N
7 SLP_S5#_TBT 8 Net Name
9 Ground 10 SMBCLK_VSB
11 DG_PEWake 12 SMBDATA_VSB
13 TBT_RTD3_PWR_EN 14 Ground
15 TBT_Card_DET_R# 12 PD_IRQ#
20
1
212
11
1 SPI Power 2 SPI Chip Select
3
Master In Slave Out
(SPI Data)
4
Master Out Slave In
(SPI Data)
5 Reserved 6 SPI Clock
7 Ground 8 SPI Reset
9 Reserved 10 No Pin
11 Reserved 12 Interrupt Request
1
1 Ground 2 +12V
3 Sense 4 Speed Control Signal
CPU_FAN1 2A 24W
PUMP_FAN1 3A 36W
SYS_FAN1~6 1A 12W
1
1 Ground 2 Voltage Control
3 Sense 4 NC
21
Reset
1
2 10
9
1 DCD 2 SIN
3 SOUT 4 DTR
5 Ground 6 DSR
7 RTS 8 CTS
9 RI 10 No Pin
1
2 6
5
1 No pin 2 NC
3 MCU_SMB_SCL_M 4 MCU_SMB_SDA_M
5 VCC5 6 Ground
22
BIOS
11 +5V 2 Data
3 No Pin 4 Ground
23
11 +12V 2 G
3 R 4 B
24
®
http://download.msi.com/manual/mb/MSICENTER.pdf
25
26
:
http://download.msi.com/manual/mb/Intel500BIOSsc.pdf
27
28
1
3
4
10
…………………………………………………………………………….10
…………………………………………………………………………………………..10
11
…………………………………………………………………………………………………….12
…………………………………………………………………………………………………13
……………………………………………………………………………..14
…………………………………………………………………………….15
……………………………………………………………………………………15
…………………………………………………………………………..16
………………………………………………………………………………16
ATX_PWR1, CPU_PWR1~2, PCIE_PWR1:
…………………………………………….17
………………………………………………………………………………..18
……………………………………………………………..18
……………………………………………………………….19
……………………………………………………………………19
……………………………………20
………………………………………………………………………………….20
………………………………………………………………………………………21
……………………………………………………………………………………..21
……………………………………………………………………………..21
………………………………………………………22
……………………………………………………………22
………………………………………………………………………………….23
………………………………………………………………………………………….23
24
………………………………………………………………………………………..24
………………………………………………………………………………………………24
MSI Center ………………………………………………………………………………………………….24
2
25
……………………………………………………………………………………………………26
…………………………………………………………………………………………….26
………………………………………………………………………………………….26
……………………………………………………………………………………………………27
……………………………………………………………………………………………………27
3
4
Intel®
JEDEC & POR)
5
60Hz*/**
Intel® Wi-Fi 6E AX210
2.4Gbps
Intel® Optane™ Memory Ready***
10
6
USB 2.0 Hubs GL850G
7
ATX
UEFI AMI BIOS
ACPI 6.2, SMBIOS 3.0
MSI Center
Intel® Extreme Tuning Utility
CPU-Z MSI GAMING
Norton™ Internet Security Solution
8
Mystic Light
LAN Manager
User Scenario
Hardware Monitor
Frozr AI Cooling
True Color
Live Update
Speed Up
Smart Tool
Super Charger
Intel WiFi (Z590 PRO WIFI)
M.2 Shield Frozr
9
Lightning Gen 4 M.2
Lightning USB 20G
USB 3.2 Gen 2 10G
MSI Center
10
USB 3.2 Gen 1
5Gbps Type-A
DisplayPort
USB 2.0 Type-A
USB 2.0 Type-A
USB 3.2 Gen 2×2
20Gbps Type-C USB 3.2 Gen 2
10Gbps Type-A
2468
11
SATA6
SATA5
SYS_FAN5
SYS_FAN4
JCOM1
JTBT1
JFP2
JTPM1
JRGB1
JCI1
M2_3
M2_2
M2_1
SYS_FAN1
JUSB4
JUSB5
JUSB3
JUSB1
JUSB2
PCIE_PWR1
SYS_FAN3
SYS_FAN2
CPU_FAN1
SYS_FAN6
PUMP_FAN1
PCI_E1
PCI_E2
PCI_E3
JBAT1
PCI_E4
JDASH1
CPU_PWR1
CPU_PWR2
JRAINBOW2
JAUD1
JRAINBOW1
JFP1
ATX_PWR1
DIMMB1
DIMMB2
DIMMA1
DIMMA2
50.77mm*
12
1
4
6
5
78
9
3
2
13
DIMMB2
DIMMA2 DIMMA2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
1
1
2
3
3
2
14
15
1
2 10
9
+
+
+— ——
—
+
Power LED
HDD LED Reset Switch
Reserved
Power Switch 1 HDD LED + 2 Power LED +
3 HDD LED — 4 Power LED —
5 Reset Switch 6 Power Switch
7 Reset Switch 8 Power Switch
9 Reserved 10 No Pin
JFP2 1
+
+—
—
Speaker
Buzzer 1 Speaker — 2 Buzzer +
3 Buzzer — 4 Speaker +
HDD LED
RESET SW
HDD LED HDD LED —
HDD LED +
POWER LED —
POWER LED +
POWER LED
JFP1
1
2 10
9
1 MIC L 2 Ground
3 MIC R 4 NC
5 Head Phone R 6 MIC Detection
7 SENSE_SEND 8 No Pin
9 Head Phone L 10 Head Phone Detection
16
SATA1
SATA3
SATA2
SATA6
SATA5
SATA4
1
3
30º30º
2
17
24
131
12
ATX_PWR1
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 Ground 15 Ground
4 +5V 16 PS-ON#
5 Ground 17 Ground
6 +5V 18 Ground
7 Ground 19 Ground
8 PWR OK 20 Res
9 5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 Ground
3
2 1
4CPU_PWR2 1 Ground 3 +12V
2 Ground 8 +12V
5
41
8
CPU_PWR1
1 Ground 5 +12V
2 Ground 6 +12V
3 Ground 7 +12V
4 Ground 8 +12V
1 3
64
PCIE_PWR1
1 +12V 4 Ground
2 +12V 5 Ground
3 +12V 6 Ground
18
1
10 11
20
1 Power 11 USB2.0+
2 USB3_RX_DN 12 USB2.0-
3 USB3_RX_DP 13 Ground
4 Ground 14 USB3_TX_C_DP
5 USB3_TX_C_DN 15 USB3_TX_C_DN
6 USB3_TX_C_DP 16 Ground
7 Ground 17 USB3_RX_DP
8 USB2.0- 18 USB3_RX_DN
9 USB2.0+ 19 Power
10 Ground 20 No Pin
1
2 10
9
1 VCC 2 VCC
3 USB0- 4 USB1-
5 USB0+ 6 USB1+
7 Ground 8 Ground
9 No Pin 10 NC
19
JUSB1
1
2 16
15
1 TBT_Force_PWR 2 TBT_S0IX_Entry_REQ
3 TBT_CIO_Plug_Event# 4 TBT_S0IX_Entry_ACK
5 SLP_S3#_TBT 6 TBT_PSON_Override_N
7 SLP_S5#_TBT 8 Net Name
9 Ground 10 SMBCLK_VSB
11 DG_PEWake 12 SMBDATA_VSB
13 TBT_RTD3_PWR_EN 14 Ground
15 TBT_Card_DET_R# 12 PD_IRQ#
20
1
212
11
1 SPI Power 2 SPI Chip Select
3
Master In Slave Out
(SPI Data)
4
Master Out Slave In
(SPI Data)
5 Reserved 6 SPI Clock
7 Ground 8 SPI Reset
9 Reserved 10 No Pin
11 Reserved 12 Interrupt Request
1
1 Ground 2 +12V
3 Sense 4 Speed Control Signal
CPU_FAN1 2A 24W
PUMP_FAN1 3A 36W
SYS_FAN1~6 1A 12W
1
1 Ground 2 Voltage Control
3 Sense 4 NC
21
Reset
1
2 10
9
1 DCD 2 SIN
3 SOUT 4 DTR
5 Ground 6 DSR
7 RTS 8 CTS
9 RI 10 No Pin
1
2 6
5
1 No pin 2 NC
3 MCU_SMB_SCL_M 4 MCU_SMB_SDA_M
5 VCC5 6 Ground
22
11 +5V 2 Data
3 No Pin 4 Ground
23
—
—
11 +12V 2 G
3 R 4 B
24
®
http://download.msi.com/manual/mb/MSICENTER.pdf
25
26
:
:
:
:
:
:
:
:
:
: *
:
:
http://download.msi.com/manual/mb/Intel500BIOStc.pdf
27
28
1
3
4
10
…………………………………………………………………………………..10
…………………………………………………………………………………10
11
………………………………………………………………………………………………… 12
………………………………………………………………………………………………13
…………………………………………………………………………. 14
……………………………………………………………15
……………………………………………………………..15
…………………………………………………………………..16
………………………………………………………………………… 16
ATX_PWR1
CPU_PWR1~2
PCIE_PWR1:
……………………………………17
………………………………………………………………………..18
……………………………………………………..18
……………………………………………………….19
………………………………………………………19
……………………………….20
………………………………………………………………….20
……………………………………………………………….21
………………………………………………………………….21
………………………………………………21
……………………………………………………22
…………………………………………………….22
………………………………………………………………………….23
EZ Debug LED ……………………………………………………………………………………………..23
24
…………………………………………………………………………..24
………………………………………………………………………………24
MSI Center ………………………………………………………………………………………………….24
2
25
…………………………………………………………………………………………………26
………………………………………………………………………….26
………………………………………………………………………………….. 26
…………………………………………………………………………………………….27
……………………………………………………………………………….27
3
4
Intel®
5
Intel® Wi-Fi 6E AX210
6
USB 2.0 Hubs GL850G
3 (M-Key)
USB 3.2 Gen 2 10Gbps Type-C x1
7
EZ Debug LED x4
DisplayPort x1
12 in. x 9.6 in. (30.5 cm x 24.4 cm)
UEFI AMI BIOS
ACPI 6.2, SMBIOS 3.0
MSI Center
Intel® Extreme Tuning Utility
CPU-Z MSI GAMING
Google Chrome™, Google Toolbar, Google Drive
Norton™ Internet Security Solution
8
Mystic Light
LAN Manager
User Scenario
Hardware Monitor
Frozr AI Cooling
True Color
Live Update
Speed Up
Smart Tool
Super Charger
Audio Boost
2.5G LAN
Intel WiFi (Z590 PRO WIFI)
M.2 Shield Frozr
LED
Mystic Light SYNC
EZ DEBUG LED
9
Lightning Gen 4 M.2
DDR4 Boost
Core Boost
Lightning USB 20G
USB 3.2 Gen 2 10G
PCI-E Steel Armor
MSI Center
Click BIOS 5
10
Off
Off 10 Mbps
100/ 1000 Mbps
2.5 Gbps
USB 3.2 Gen 1
5Gbps Type-A
2.5 Gbps LAN
DisplayPort
USB 2.0 Type-A
USB 2.0 Type-A
USB 3.2 Gen 2×2
20Gbps Type-C USB 3.2 Gen 2
10Gbps Type-A
Flash BIOS
2468
11
SATA6
SATA5
SYS_FAN5
SYS_FAN4
JCOM1
JTBT1
JFP2
JTPM1
JRGB1
JCI1
M2_3
M2_2
M2_1
SYS_FAN1
JUSB4
JUSB5
JUSB3
JUSB1
JUSB2
PCIE_PWR1
SYS_FAN3
SYS_FAN2
CPU_FAN1
SYS_FAN6
PUMP_FAN1
PCI_E1
PCI_E2
PCI_E3
JBAT1
PCI_E4
JDASH1
CPU_PWR1
CPU_PWR2
JRAINBOW2
JAUD1
JRAINBOW1
JFP1
ATX_PWR1
DIMMB1
DIMMB2
DIMMA1
DIMMA2
50.77mm*
12
1
4
6
5
78
9
3
2
13
DIMMB2
DIMMA2 DIMMA2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
1
1
2
3
3
2
14
15
1
2 10
9
+
+
+— ——
—
+
Power LED
HDD LED Reset Switch
Reserved
Power Switch 1 HDD LED + 2 Power LED +
3 HDD LED — 4 Power LED —
5 Reset Switch 6 Power Switch
7 Reset Switch 8 Power Switch
9 Reserved 10 No Pin
JFP2 1
+
+—
—
Speaker
Buzzer 1 Speaker — 2 Buzzer +
3 Buzzer — 4 Speaker +
HDD LED
RESET SW
HDD LED HDD LED —
HDD LED +
POWER LED —
POWER LED +
POWER LED
JFP1
1
2 10
9
1 MIC L 2 Ground
3 MIC R 4 NC
5 Head Phone R 6 MIC Detection
7 SENSE_SEND 8 No Pin
9 Head Phone L 10 Head Phone Detection
16
SATA1
SATA3
SATA2
SATA6
SATA5
SATA4
1
3
30º30º
2
17
24
131
12
ATX_PWR1
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 Ground 15 Ground
4 +5V 16 PS-ON#
5 Ground 17 Ground
6 +5V 18 Ground
7 Ground 19 Ground
8 PWR OK 20 Res
9 5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 Ground
3
2 1
4CPU_PWR2 1 Ground 3 +12V
2 Ground 8 +12V
5
41
8
CPU_PWR1
1 Ground 5 +12V
2 Ground 6 +12V
3 Ground 7 +12V
4 Ground 8 +12V
1 3
64
PCIE_PWR1
1 +12V 4 Ground
2 +12V 5 Ground
3 +12V 6 Ground
18
1
10 11
20
1 Power 11 USB2.0+
2 USB3_RX_DN 12 USB2.0-
3 USB3_RX_DP 13 Ground
4 Ground 14 USB3_TX_C_DP
5 USB3_TX_C_DN 15 USB3_TX_C_DN
6 USB3_TX_C_DP 16 Ground
7 Ground 17 USB3_RX_DP
8 USB2.0- 18 USB3_RX_DN
9 USB2.0+ 19 Power
10 Ground 20 No Pin
1
2 10
9
1 VCC 2 VCC
3 USB0- 4 USB1-
5 USB0+ 6 USB1+
7 Ground 8 Ground
9 No Pin 10 NC
19
JUSB1
1
2 16
15
1 TBT_Force_PWR 2 TBT_S0IX_Entry_REQ
3 TBT_CIO_Plug_Event# 4 TBT_S0IX_Entry_ACK
5 SLP_S3#_TBT 6 TBT_PSON_Override_N
7 SLP_S5#_TBT 8 Net Name
9 Ground 10 SMBCLK_VSB
11 DG_PEWake 12 SMBDATA_VSB
13 TBT_RTD3_PWR_EN 14 Ground
15 TBT_Card_DET_R# 12 PD_IRQ#
20
1
212
11
1 SPI Power 2 SPI Chip Select
3
Master In Slave Out
(SPI Data)
4
Master Out Slave In
(SPI Data)
5 Reserved 6 SPI Clock
7 Ground 8 SPI Reset
9 Reserved 10 No Pin
11 Reserved 12 Interrupt Request
1
1 Ground 2 +12V
3 Sense 4 Speed Control Signal
CPU_FAN1 2A 24W
PUMP_FAN1 3A 36W
SYS_FAN1~6 1A 12W
1
1 Ground 2 Voltage Control
3 Sense 4 NC
21
Reset
1
2 10
9
1 DCD 2 SIN
3 SOUT 4 DTR
5 Ground 6 DSR
7 RTS 8 CTS
9 RI 10 No Pin
1
2 6
5
1 No pin 2 NC
3 MCU_SMB_SCL_M 4 MCU_SMB_SDA_M
5 VCC5 6 Ground
22
11 +5V 2 Data
3 No Pin 4 Ground
23
11 +12V 2 G
3 R 4 B
24
Windows®
®
http://download.msi.com/manual/mb/MSICENTER.pdf
25
26
:
:
:
:
:
: O
:
:
:
: *
:
http://download.msi.com/manual/mb/Intel500BIOSjp.pdf
27
28
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Caution: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
Tested to comply with FCC standards
FOR HOME OR OFFICE USE
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference
that may cause undesired operation.
Products bearing the CE marking
comply with one or more of the
following EU Directives as may be
applicable:
RED 2014/53/EU; Low Voltage Directive 2014/35/
EU; EMC Directive 2014/30/EU; RoHS Directive
2011/65/EU.
Compliance with these directives is assessed
using applicable European Harmonized
Standards. The point of contact for regulatory
matters is MSI, MSI-NL Eindhoven 5706 5692
ER Son.
10-7D09
Z590PW
European Union:
Batteries, battery packs, and
accumulators should not be
disposed of as unsorted household
waste. Please use the public
collection system to return, recycle,
or treat them in compliance with the
local regulations.
Taiwan:
For better environmental protection,
waste batteries should be collected
separately for recycling or special
disposal.
California, USA:
The button cell battery may contain
perchlorate material and requires
special handling when recycled or
disposed of in California.
For further information please visit:
http://www.dtsc.ca.gov/hazardouswaste/
perchlorate/
CAUTION: There is a risk of explosion, if battery
is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
ENGLISH
To protect the global environment
and as an environmentalist, MSI
must remind you that…
Under the European Union (“EU”)
Directive on Waste Electrical and
Electronic Equipment, Directive
2002/96/EC, which takes effect
on August 13, 2005, products of
“electrical and electronic equipment” cannot be
discarded as municipal wastes anymore, and
manufacturers of covered electronic equipment
will be obligated to take back such products at
the end of their useful life. MSI will comply with
the product take back requirements at the end
of life of MSI-branded products that are sold into
the EU. You can return these products to local
collection points.
DEUTSCH
Hinweis von MSI zur Erhaltung und Schutz
unserer Umwelt
Gemäß der Richtlinie 2002/96/EG über
Elektro- und Elektronik-Altgeräte dürfen
Elektro- und Elektronik-Altgeräte nicht
mehr als kommunale Abfälle entsorgt
werden. MSI hat europaweit verschiedene
Sammel- und Recyclingunternehmen
beauftragt, die in die Europäische Union
in Verkehr gebrachten Produkte, am Ende
seines Lebenszyklus zurückzunehmen. Bitte
entsorgen Sie dieses Produkt zum gegebenen
Zeitpunkt ausschliesslich an einer lokalen
Altgerätesammelstelle in Ihrer Nähe.
FRANÇAIS
En tant qu’écologiste et afin de protéger
l’environnement, MSI tient à rappeler ceci…
Au sujet de la directive européenne (EU) relative
aux déchets des équipement électriques et
électroniques, directive 2002/96/EC, prenant
effet le 13 août 2005, que les produits
électriques et électroniques ne peuvent être
déposés dans les décharges ou tout simplement
mis à la poubelle. Les fabricants de ces
équipements seront obligés de récupérer
certains produits en fin de vie. MSI prendra en
compte cette exigence relative au retour des
produits en fin de vie au sein de la communauté
européenne. Par conséquent vous pouvez
retourner localement ces matériels dans les
points de collecte.
ESPAÑOL
MSI como empresa comprometida con la
protección del medio ambiente, recomienda:
Bajo la directiva 2002/96/EC de la Unión
Europea en materia de desechos y/o equipos
electrónicos, con fecha de rigor desde el 13 de
agosto de 2005, los productos clasificados como
“eléctricos y equipos electrónicos” no pueden
ser depositados en los contenedores habituales
de su municipio, los fabricantes de equipos
electrónicos, están obligados a hacerse cargo
de dichos productos al termino de su período de
vida. MSI estará comprometido con los términos
de recogida de sus productos vendidos en la
Unión Europea al final de su periodo de vida.
Usted debe depositar estos productos en el
punto limpio establecido por el ayuntamiento
de su localidad o entregar a una empresa
autorizada para la recogida de estos residuos.
NEDERLANDS
Om het milieu te beschermen, wil MSI u eraan
herinneren dat….
De richtlijn van de Europese Unie (EU) met
betrekking tot Vervuiling van Electrische en
Electronische producten (2002/96/EC), die op
13 Augustus 2005 in zal gaan kunnen niet meer
beschouwd worden als vervuiling. Fabrikanten
van dit soort producten worden verplicht om
producten retour te nemen aan het eind van
hun levenscyclus. MSI zal overeenkomstig de
richtlijn handelen voor de producten die de
merknaam MSI dragen en verkocht zijn in de EU.
Deze goederen kunnen geretourneerd worden
op lokale inzamelingspunten.
SRPSKI
mora da vas podesti da…
2002/96/EC, koja stupa na snagu od 13. Avgusta
2005, proizvodi koji spadaju pod “elektronsku i
proizvoda kojima je istekao vek trajanja, koji
imaju MSI oznaku i koji su prodati u EU. Ove
za prikupljanje.
POLSKI
elektronicznych (Dyrektywa 2002/96/EC), która
(sprzedawane na terenie Unii Europejskiej)
zbiorczych.
TÜRKÇE
itibaren geçerli olmak üzere, elektrikli ve
sonra ürünleri geri toplamakla yükümlü
EC platné od 13. srpna 2005 je zakázáno
likvidovat “elektrické a elektronické výrobky”
MAGYAR
Annak érdekében, hogy környezetünket
az MSI emlékezteti Önt, hogy …
Az Európai Unió („EU”) 2005. augusztus 13-án
berendezések hulladékairól szóló 2002/96/
EK irányelve szerint az elektromos és
elektronikus berendezések többé nem
elektronikus berendezések gyártói kötelessé
válnak az ilyen termékek visszavételére
azok hasznos élettartama végén. Az MSI
betartja a termékvisszavétellel kapcsolatos
követelményeket az MSI márkanév alatt az EU-n
belül értékesített termékek esetében, azok
élettartamának végén. Az ilyen termékeket a
ITALIANO
Per proteggere l’ambiente, MSI, da sempre
amica della natura, ti ricorda che….
In base alla Direttiva dell’Unione Europea
(EU) sullo Smaltimento dei Materiali Elettrici
ed Elettronici, Direttiva 2002/96/EC in vigore
dal 13 Agosto 2005, prodotti appartenenti alla
categoria dei Materiali Elettrici ed Elettronici
non possono più essere eliminati come rifiuti
municipali: i produttori di detti materiali saranno
obbligati a ritirare ogni prodotto alla fine del
suo ciclo di vita. MSI si adeguerà a tale Direttiva
ritirando tutti i prodotti marchiati MSI che sono
stati venduti all’interno dell’Unione Europea alla
fine del loro ciclo di vita. È possibile portare i
prodotti nel più vicino punto di raccolta
https://storage-asset.msi.com/html/popup/csr/
cemm_jp.html
This product complies with the “India
E-waste (Management and Handling) Rule
2011” and prohibits use of lead, mercury,
hexavalent chromium, polybrominated
biphenyls or polybrominated diphenyl ethers in
concentrations exceeding 0.1 weight % and 0.01
weight % for cadmium, except for the exemptions
set in Schedule 2 of the Rule.
Uygundur
The product has been designed
to enable proper reuse of parts
and recycling and should not be
thrown away at its end of life.
Users should contact the local
authorized point of collection
for recycling and disposing of their end-of-life
products.
Visit the MSI website and locate a nearby
distributor for further recycling information.
Users may also reach us at gpcontdev@
msi.com for information regarding proper
Disposal, Take-back, Recycling, and
Disassembly of MSI products.
In compliance with chemical substances
regulations, such as the EU REACH Regulation
(Regulation EC No. 1907/2006 of the European
Parliament and the Council), MSI provides
the information of chemical substances in
products at:
https://storage-asset.msi.com/html/popup/csr/
evmtprtt_pcm.html
This device is restricted to indoor use when
operating in the 2.4GHz, 5GHz frequency band.
Cet appareil doit être utilisé à l’intérieur.
This product incorporates a radio transmitting
and receiving device. For computers in normal
use, a separation distance of 20 cm ensures
that radio frequency exposure levels comply
with EU requirements. Products designed to
be operated at closer proximities, such as
tablet computers, comply with applicable EU
requirements in typical operating positions.
Products can be operated without maintaining a
separation distance unless otherwise indicated in
instructions specific to the product.
CAUTION: IEEE 802.11x wireless
band is restricted for indoor use
only in all European Union member
states, EFTA (Iceland, Norway, Liechtenstein),
and most other European countries (e.g.,
Switzerland, Turkey, Republic of Serbia). Using
this WLAN application outdoors might lead to
interference issues with existing radio services.
Radio frequency bands and maximum power
levels
Features :802.11 a/b/g/n/ac/ax, BT
Frequency Range :2.4GHz, 5GHz
Modulation :FHSS, DSSS, OFDM
Power Output :10, 20, 23
Channel Band Width :1, 5, 20 ,40 , 80, 160MHz
Micro-Star Int’l Co.,Ltd.
Copyright © 2021 All rights reserved.
The MSI logo used is a registered trademark of
Micro-Star Int’l Co., Ltd. All other marks and
names mentioned may be trademarks of their
respective owners. No warranty as to accuracy
or completeness is expressed or implied. MSI
reserves the right to make changes to this
document without prior notice.
Version 1.0, 2021/01, First release.
If a problem arises with your system and no
solution can be obtained from the user guide,
please contact your place of purchase or
local distributor. Alternatively, please try the
following help resources for further guidance.
Visit the MSI website for technical guide,
BIOS updates, driver updates, and other
information: http://
Register your product at: http://
(Pb)
(Hg)
(Cd)
(Cr(VI))
(PBB)
(PBDE)
(Pb)
(Hg)
(Cd)
(Cr+6)
(PBB)
(PBDE)
1
<變數 1> Contents
Contents
Safety Information ……………………………………………………………………………….3
Specifications ………………………………………………………………………………………4
Rear I/O Panel …………………………………………………………………………………..10
LAN Port LED Status Table …………………………………………………………………………..10
Audio Ports Configuration …………………………………………………………………………….10
Overview of Components ……………………………………………………………………11
CPU Socket …………………………………………………………………………………………………12
DIMM Slots………………………………………………………………………………………………….13
DIMM Slots………………………………………………………………………………………………….13
PCI_E1~4: PCIe Expansion Slots ……………………………………………………………………14
JFP1, JFP2: Front Panel Connectors ……………………………………………………………..15
JAUD1: Front Audio Connector ……………………………………………………………………..15
SATA1~6: SATA 6Gb/s Connectors …………………………………………………………………16
M2_1~3: M.2 Slot (Key M) ……………………………………………………………………………..16
ATX_PWR1, CPU_PWR1~2, PCIE_PWR1: Power Connectors ……………………………17
JUSB1~2: USB 2.0 Connectors ………………………………………………………………………18
JUSB3~4: USB 3.2 Gen 1 5Gbps Connector …………………………………………………….18
JUSB1: USB 3.2 Gen 2 Type-C Connector ……………………………………………………….19
JTBT1: Thunderbolt Add-on Card Connector ………………………………………………….19
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors ………………………………..20
JTPM1: TPM Module Connector …………………………………………………………………….20
JCI1: Chassis Intrusion Connector …………………………………………………………………21
JCOM1: Serial Port Connector ………………………………………………………………………21
JDASH1: Tuning controller Connector ……………………………………………………………21
JBAT1: Clear CMOS (Reset BIOS) Jumper ………………………………………………………22
JRAINBOW1~2: Addressable RGB LED connectors …………………………………………22
JRGB1: RGB LED connector ………………………………………………………………………….23
EZ Debug LED ……………………………………………………………………………………………..23
Installing OS, Drivers & MSI Center ……………………………………………………..24
Installing Windows® 10 …………………………………………………………………………………24
Installing Drivers …………………………………………………………………………………………24
MSI Center ………………………………………………………………………………………………….24
Thank you for purchasing the MSI® Z590 PRO WIFI/ Z590-A
PRO motherboard. This User Guide gives information about
board layout, component overview, BIOS setup and software
installation.
1
Contents
Contents
3
4
10
LAN Port LED Status Table …………………………………………………………………………..10
Audio Ports Configuration …………………………………………………………………………….10
11
CPU Socket …………………………………………………………………………………………………12
DIMM Slots………………………………………………………………………………………………….13
DIMM Slots………………………………………………………………………………………………….13
PCI_E1~4: PCIe Expansion Slots ……………………………………………………………………14
JFP1, JFP2: Front Panel Connectors ……………………………………………………………..15
JAUD1: Front Audio Connector ……………………………………………………………………..15
SATA1~6: SATA 6Gb/s Connectors …………………………………………………………………16
M2_1~3: M.2 Slot (Key M) ……………………………………………………………………………..16
ATX_PWR1, CPU_PWR1~2, PCIE_PWR1: Power Connectors ……………………………17
JUSB1~2: USB 2.0 Connectors ………………………………………………………………………18
JUSB3~4: USB 3.2 Gen 1 5Gbps Connector …………………………………………………….18
JUSB1: USB 3.2 Gen 2 Type-C Connector ……………………………………………………….19
JTBT1: Thunderbolt Add-on Card Connector ………………………………………………….19
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors ………………………………..20
JTPM1: TPM Module Connector …………………………………………………………………….20
JCI1: Chassis Intrusion Connector …………………………………………………………………21
JCOM1: Serial Port Connector ………………………………………………………………………21
JDASH1: Tuning controller Connector ……………………………………………………………21
JBAT1: Clear CMOS (Reset BIOS) Jumper ………………………………………………………22
JRAINBOW1~2: Addressable RGB LED connectors …………………………………………22
JRGB1: RGB LED connector ………………………………………………………………………….23
EZ Debug LED ……………………………………………………………………………………………..23
24
Installing Windows® 10 …………………………………………………………………………………24
Installing Drivers …………………………………………………………………………………………24
MSI Center ………………………………………………………………………………………………….24
Thank you for purchasing the MSI®
motherboard. This User Guide gives information about
board layout, component overview, BIOS setup and software
installation.
1< 1> Contents
Contents Safety Information ……………………………………………………………………………….3
Specifications ………………………………………………………………………………………4
Rear I/O Panel …………………………………………………………………………………..10 LAN Port LED Status Table …………………………………………………………………………..10 Audio Ports Configuration …………………………………………………………………………….10
Overview of Components ……………………………………………………………………11 CPU Socket …………………………………………………………………………………………………12 DIMM Slots………………………………………………………………………………………………….13 PCI_E1~4: PCIe Expansion Slots ……………………………………………………………………14 JFP1, JFP2: Front Panel Connectors ……………………………………………………………..15 JAUD1: Front Audio Connector ……………………………………………………………………..15 SATA1~6: SATA 6Gb/s Connectors …………………………………………………………………16 M2_1~2: M.2 Slot (Key M) ……………………………………………………………………………..16 ATX_PWR1, CPU_PWR1~2, PCIE_PWR1: Power Connectors ……………………………17 JUSB1~2: USB 2.0 Connectors ………………………………………………………………………18 JUSB3~4: USB 3.2 Gen 1 5Gbps Connector …………………………………………………….18 JUSB1: USB 3.2 Gen 2 Type-C Connector ……………………………………………………….19 JTBT1: Thunderbolt Add-on Card Connector ………………………………………………….19 CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors ………………………………..20 JTPM1: TPM Module Connector …………………………………………………………………….20 JCI1: Chassis Intrusion Connector …………………………………………………………………21 JDASH1: Tuning controller Connector ……………………………………………………………21 JBAT1: Clear CMOS (Reset BIOS) Jumper ………………………………………………………22 JRAINBOW1~2: Addressable RGB LED connectors …………………………………………22 JRGB1: RGB LED connector ………………………………………………………………………….23 EZ Debug LED ……………………………………………………………………………………………..23
Installing OS, Drivers & MSI Center ……………………………………………………..24 Installing Windows 10 …………………………………………………………………………………24 Installing Drivers …………………………………………………………………………………………24 MSI Center ………………………………………………………………………………………………….24
UEFI BIOS ………………………………………………………………………………………….25 BIOS Setup ………………………………………………………………………………………………….26
Thank you for purchasing the MSI Z590 PRO WIFI (CEC) motherboard. This User Guide gives information about board layout, component overview, BIOS setup and software installation.
2 Contents
Entering BIOS Setup …………………………………………………………………………………….26 BIOS User Guide ………………………………………………………………………………………….26 Resetting BIOS …………………………………………………………………………………………….27 Updating BIOS……………………………………………………………………………………………..27
3Contents Safety Information
Safety Information The components included in this package are prone to damage from electrostatic
discharge (ESD). Please adhere to the following instructions to ensure successful computer assembly.
Ensure that all components are securely connected. Loose connections may cause the computer to not recognize a component or fail to start.
Hold the motherboard by the edges to avoid touching sensitive components. It is recommended to wear an electrostatic discharge (ESD) wrist strap when
handling the motherboard to prevent electrostatic damage. If an ESD wrist strap is not available, discharge yourself of static electricity by touching another metal object before handling the motherboard.
Store the motherboard in an electrostatic shielding container or on an anti-static pad whenever the motherboard is not installed.
Before turning on the computer, ensure that there are no loose screws or metal components on the motherboard or anywhere within the computer case.
Do not boot the computer before installation is completed. This could cause permanent damage to the components as well as injury to the user.
If you need help during any installation step, please consult a certified computer technician.
Always turn off the power supply and unplug the power cord from the power outlet before installing or removing any computer component.
Keep this user guide for future reference. Keep this motherboard away from humidity. Make sure that your electrical outlet provides the same voltage as is indicated on
the PSU, before connecting the PSU to the electrical outlet. Place the power cord such a way that people can not step on it. Do not place
anything over the power cord. All cautions and warnings on the motherboard should be noted. If any of the following situations arises, get the motherboard checked by service
personnel: Liquid has penetrated into the computer. The motherboard has been exposed to moisture. The motherboard does not work well or you can not get it work according to
user guide. The motherboard has been dropped and damaged. The motherboard has obvious sign of breakage.
Do not leave this motherboard in an environment above 60C (140F), it may damage the motherboard.
4 Specifications
Specifications
CPU
Supports 10th Gen Intel Core Processors, 11th Gen Intel Core Processors, Pentium Gold and Celeron Processors*
Processor socket LGA1200 * Please go to intel.com for compatibility information
Chipset Intel Z590 chipset
Memory
4x DDR4 memory slots, support up to 128GB* Supports 1R 2133/ 2666/ 2933 MHz for 10th Gen Intel CPU
(by JEDEC & POR) Supports 1R 2133/ 2666/ 2933/ 3200 MHz for 11th Gen Intel
CPU (by JEDEC & POR) Max overclocking frequency:
1DPC 1R Max speed up to 5333 MHz 1DPC 2R Max speed up to 4700+ MHz 2DPC 1R Max speed up to 4400+ MHz 2DPC 2R Max speed up to 4000+ MHz
Supports Dual-Channel mode Supports non-ECC, un-buffered memory Supports Intel Extreme Memory Profile (XMP)
*Please refer www.msi.com for more information on compatible memory
Expansion Slots
4x PCIe x16 slots Support x16/ x1/ x4/ x1 PCI_E1 (from CPU)
Supports up to PCIe 4.0 for 11th Gen Intel CPU Supports up to PCIe 3.0 for 10th Gen Intel CPU
PCI_E2 & PCI_E4 (from Z590 chipset) Supports up to PCIe 3.0 x1
PCI_E3 (from Z590 chipset) Supports up to PCIe 3.0 x4
Audio Realtek ALC897 Codec
7.1-Channel High Definition Audio
Multi-GPU Supports 2-Way AMD CrossFire Technology
Continued on next page
5Specifications Specifications
Continued from previous page
Onboard Graphics
1x HDMI 2.0b with HDR port, supports a maximum resolution of 4K 60Hz */**
1x DisplayPort 1.4 port, supports a maximum resolution of 4K 60Hz */** * Available only on processors featuring integrated graphics. ** Graphics specifications may vary depending on the CPU installed.
LAN 1x Intel I225-V 2.5Gbps LAN controller
Wireless LAN & Bluetooth
Intel Wi-Fi 6E AX210 The Wireless module is pre-installed in the M.2 (Key-E) slot Supports MU-MIMO TX/RX, 2.4GHz/ 5GHz/ 6GHz* (160MHz)
up to 2.4Gbps Supports 802.11 a/ b/ g/ n/ ac/ ax Supports Bluetooth 5.2**, FIPS, FISMA
* Wi-Fi 6E 6GHz may depend on every countrys regulations and will be ready in WIN10 21H1. ** Bluetooth 5.2 will be ready in WIN10 21H1.
Storage
6x SATA 6Gb/s ports (from Z590 chipset)* 2x M.2 slots (Key M)
M2_1 slot (from CPU) Available only on 11th Gen Intel CPU Supports up to PCIe 4.0×4 Supports 2242/ 2260/ 2280/ 22110 storage devices
M2_2 slots (from Z590 chipset)* Support up to PCIe 3.0×4 Support up to SATA 6Gb/s Support 2242/ 2260/ 2280 storage devices Intel Optane Memory Ready**
Support Intel Smart Response Technology for Intel Core processors * SATA5 & SATA 6 will be unavailable when installing M.2 SSD in the M2_2 slot. ** Before using Intel Optane memory modules, please ensure that you have updated the drivers and BIOS to the latest version from MSI website.
Continued on next page
6 Specifications
Continued from previous page
RAID Supports RAID 0, RAID 1, RAID 5 and RAID 10 for SATA
storage devices Supports RAID 0 and RAID 1 for M.2 NVMe storage devices
USB
Intel Z590 Chipset 1x USB 3.2 Gen 2×2 20Gbps Type-C port on the back
panel 2x USB 3.2 Gen 2 10Gbps ports (1 Type-C internal
connector and 1 Type-A port on the back panel) 6x USB 3.2 Gen 1 5Gbps ports (2 Type-A ports on the
back panel, and 4 ports available through the internal USB 3.2 Gen 1 5Gbps connectors)
USB 2.0 Hubs GL850G 4x USB 2.0 Type-A ports on the back panel 4x USB 2.0 ports available through the internal USB 2.0
connectors
Internal Connectors
1x 24-pin ATX main power connector 1x 8-pin ATX 12V power connector 1x 4-pin ATX 12V power connector 1x 6-pin ATX PCIe power connector 6x SATA 6Gb/s connectors 2x M.2 slots (M-Key) 1x USB 3.2 Gen 2 10Gbps Type-C port 2x USB 3.2 Gen 1 5Gbps connectors (supports additional 4
USB 3.2 Gen 1 5Gbps ports) 2x USB 2.0 connectors (supports additional 4 USB 2.0 ports) 1x 4-pin CPU fan connector 1x 4-pin water-pump fan connector 6x 4-pin system fan connectors 1x Front panel audio connector 2x System panel connectors 1x Chassis Intrusion connector 1x Clear CMOS jumper 1x TPM module connector 1x Tuning controller connector 1x TBT connector (Supports RTD3)
Continued on next page
7Specifications Specifications
Continued from previous page
LED Features 1x 4-pin RGB LED connector 2x 3-pin RAINBOW LED connectors 4x EZ Debug LED
Back Panel Connectors
1x Flash BIOS Button 1x PS/2 keyboard/ mouse combo port 4x USB 2.0 Type-A ports 1x DisplayPort 1x HDMI port 1x LAN (RJ45) port 2x USB 3.2 Gen 1 5Gbps Type-A ports 1x USB 3.2 Gen 2 10Gbps Type-A port 1x USB 3.2 Gen 2×2 20Gbps Type-C port 2x Wi-Fi Antenna connectors 6x audio jacks
I/O Controller NUVOTON NCT6687-R Controller Chip
Hardware Monitor
CPU/ System/ Chipset temperature detection CPU/ System/ Pump fan speed detection CPU/ System/ Pump fan speed control
Form Factor ATX Form Factor 12 in. x 9.6 in. (30.5 cm x 24.4 cm)
BIOS Features
1x 256 Mb flash UEFI AMI BIOS ACPI 6.2, SMBIOS 3.0 Multi-language
Software
Drivers MSI Center Intel Extreme Tuning Utility CPU-Z MSI GAMING Google Chrome, Google Toolbar, Google Drive Norton Internet Security Solution
Continued on next page
8 Specifications
Continued from previous page
MSI Center Features
Mystic Light LAN Manager User Scenario Hardware Monitor Frozr AI Cooling True Color Live Update Speed Up Smart Tool Super Charger
Special Features
Audio Audio Boost
Network 2.5G LAN LAN Manager Intel WiFi
Cooling Extended Heatsink Design M.2 Shield Frozr K7 thermal pad Choke pad Pump Fan Smart Fan Control
LED Mystic Light Extension (RAINBOW/RGB) Mystic Light SYNC EZ LED Control EZ DEBUG LED
Continued on next page
9Specifications Specifications
Continued from previous page
Special Features
Performance Lightning Gen 4 PCI-E Slot Lightning Gen 4 M.2 Multi GPU-CrossFire Technology DDR4 Boost Core Boost Lightning USB 20G USB 3.2 Gen 2 10G USB with Type A+C Front USB Type-C Dual CPU Power Supplemental PCIE Power Connector 2oz Copper thickened PCB
Protection PCI-E Steel Armor
Experience MSI Center Frozr AI Cooling Click BIOS 5 Flash BIOS Button
10 Rear I/O Panel
Rear I/O Panel
Link/ Activity LED
Status Description
Off No link
Yellow Linked
Blinking Data activity
Speed LED
Status Description Off 10 Mbps connection
Green 100/ 1000 Mbps connection
Orange 2.5 Gbps connection
LAN Port LED Status Table
USB 3.2 Gen 1 5Gbps Type-A
Flash BIOS Button
PS/2 Combo port 2.5 Gbps LAN
DisplayPort
USB 2.0 Type-A
USB 2.0 Type-A Audio Ports
Wi-Fi Antenna connectors
USB 3.2 Gen 2×2 20Gbps Type-C
USB 3.2 Gen 2 10Gbps Type-A
Flash BIOS Port
Audio Ports Configuration
Audio Ports Channel
2 4 6 8
Line-Out/ Front Specker Out
Line-In
Rear Speaker Out
Center/ Subwoofer Out
Side Speaker Out
Mic In
(: connected, Blank: empty)
11Rear I/O Panel Overview of Components
Overview of Components
* Distance from the center of the CPU to the nearest DIMM slot.
Processor Socket
SATA6 SATA5
SYS_FAN5
SYS_FAN4
JTBT1
JFP2
JTPM1
JRGB1
SATA12
SATA34JCI1 M2_2
M2_1
SYS_FAN1
JUSB4
JUSB5
JUSB3
JUSB1 JUSB2
PCIE_PWR1
SYS_FAN3 SYS_FAN2
CPU_FAN1
SYS_FAN6
PUMP_FAN1
PCI_E1
PCI_E2
PCI_E3 JBAT1
PCI_E4 JDASH1
CPU_PWR1
CPU_PWR2
JRAINBOW2
JAUD1
JRAINBOW1
JFP1
ATX_PWR1
DIMMB1 DIMMB2
DIMMA1 DIMMA2
50.77mm*
12 Overview of Components
CPU Socket Please install the CPU into the CPU socket as shown below.
Important Always unplug the power cord from the power outlet before installing or removing
the CPU. Please retain the CPU protective cap after installing the processor. MSI will deal
with Return Merchandise Authorization (RMA) requests if only the motherboard comes with the protective cap on the CPU socket.
When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink is necessary to prevent overheating and maintain system stability.
Confirm that the CPU heatsink has formed a tight seal with the CPU before booting your system.
Overheating can seriously damage the CPU and motherboard. Always make sure the cooling fans work properly to protect the CPU from overheating. Be sure to apply an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to enhance heat dissipation.
Whenever the CPU is not installed, always protect the CPU socket pins by covering the socket with the plastic cap.
If you purchased a separate CPU and heatsink/ cooler, Please refer to the docu- mentation in the heatsink/ cooler package for more details about installation.
1
4
6
5 7 8
9
3
2
13Overview of Components Overview of Components
DIMM Slots Please install the memory module into the DIMM slot as shown below.
DIMMB2
DIMMA2 DIMMA2
1
1
23
3
2
Memory module installation recommendation
DIMMB2 DIMMB1 DIMMA2 DIMMA1
14 Overview of Components
Important Always insert memory modules in the DIMMA2 slot first. To ensure system stability for Dual channel mode, memory modules must be of the
same type, number and density. Some memory modules may operate at a lower frequency than the marked value
when overclocking due to the memory frequency operates dependent on its Serial Presence Detect (SPD). Go to BIOS and find the DRAM Frequency to set the memory frequency if you want to operate the memory at the marked or at a higher frequency.
It is recommended to use a more efficient memory cooling system for full DIMMs installation or overclocking.
The stability and compatibility of installed memory module depend on installed CPU and devices when overclocking.
Please refer www.msi.com for more information on compatible memory.
PCI_E1~4: PCIe Expansion Slots
Important When adding or removing expansion cards, always turn off the power supply and
unplug the power supply power cable from the power outlet. Read the expansion cards documentation to check for any necessary additional hardware or software changes.
If you install a large and heavy graphics card, you need to use a tool such as MSI Gaming Series Graphics Card Bolster to support its weight to prevent deformation of the slot.
For a single PCIe x16 expansion card installation with optimum performance, using the PCI_E1 slot is recommended.
PCI_E1: PCIe 4.0/ 3.0 x16 (From CPU)
PCI_E3: PCIe 3.0 x4 (From Z590 chipset)
PCI_E4: PCIe 3.0 x1 (From Z590 chipset)
PCI_E2: PCIe 3.0 x1 (From Z590 chipset)
15Overview of Components Overview of Components
JFP1, JFP2: Front Panel Connectors These connectors connect to the switches and LEDs on the front panel.
1 2 10
9
+ +
+ —
— —
— +
Power LED
HDD LED Reset Switch
Reserved
Power Switch 1 HDD LED + 2 Power LED +
3 HDD LED — 4 Power LED —
5 Reset Switch 6 Power Switch
7 Reset Switch 8 Power Switch
9 Reserved 10 No Pin
JFP2 1
+
+ —
—
Speaker
Buzzer 1 Speaker — 2 Buzzer +
3 Buzzer — 4 Speaker +
HD D L
ED RE
SET SW
HDD LED HDD LED — HDD LED +
POWER LED — POWER LED +
POWER LED
JFP1
JAUD1: Front Audio Connector This connector allow you to connect audio jacks on the front panel.
1
2 10
9
1 MIC L 2 Ground 3 MIC R 4 NC 5 Head Phone R 6 MIC Detection 7 SENSE_SEND 8 No Pin 9 Head Phone L 10 Head Phone Detection
16 Overview of Components
SATA1~6: SATA 6Gb/s Connectors These connectors are SATA 6Gb/s interface ports. Each connector can connect to one SATA device.
SATA1
SATA3
SATA2
SATA6 SATA5
SATA4
Important SATA5 & SATA 6 will be unavailable when installing M.2 SSD in the M2_2 slot. Please do not fold the SATA cable at a 90-degree angle. Data loss may result
during transmission otherwise. SATA cables have identical plugs on either sides of the cable. However, it is
recommended that the flat connector be connected to the motherboard for space saving purposes.
M2_1~2: M.2 Slot (Key M) Please install the M.2 solid-state drive (SSD) into the M.2 slot as shown below.
1
3
Standoff
Supplied M.2 screw 30
2
17Overview of Components Overview of Components
ATX_PWR1, CPU_PWR1~2, PCIE_PWR1: Power Connectors These connectors allow you to connect an ATX power supply.
Important Make sure that all the power cables are securely connected to a proper ATX power supply to ensure stable operation of the motherboard.
24
131
12
ATX_PWR1
1 +3.3V 13 +3.3V 2 +3.3V 14 -12V 3 Ground 15 Ground 4 +5V 16 PS-ON# 5 Ground 17 Ground 6 +5V 18 Ground 7 Ground 19 Ground 8 PWR OK 20 Res 9 5VSB 21 +5V
10 +12V 22 +5V 11 +12V 23 +5V 12 +3.3V 24 Ground
3 2 1 4 CPU_PWR2
1 Ground 3 +12V
2 Ground 4 +12V
5
4 1
8
CPU_PWR1
1 Ground 5 +12V 2 Ground 6 +12V 3 Ground 7 +12V 4 Ground 8 +12V
1 3
64
PCIE_PWR1
1 +12V 4 Ground 2 +12V 5 Ground
3 +12V 6 Ground
18 Overview of Components
JUSB3~4: USB 3.2 Gen 1 5Gbps Connector This connector allows you to connect USB 3.2 Gen 1 5Gbps ports on the front panel.
1
10 11
20
1 Power 11 USB2.0+ 2 USB3_RX_DN 12 USB2.0- 3 USB3_RX_DP 13 Ground 4 Ground 14 USB3_TX_C_DP 5 USB3_TX_C_DN 15 USB3_TX_C_DN 6 USB3_TX_C_DP 16 Ground 7 Ground 17 USB3_RX_DP 8 USB2.0- 18 USB3_RX_DN 9 USB2.0+ 19 Power
10 Ground 20 No Pin
Important Note that the Power and Ground pins must be connected correctly to avoid possible damage.
JUSB1~2: USB 2.0 Connectors These connectors allow you to connect USB 2.0 ports on the front panel.
Important Note that the VCC and Ground pins must be connected correctly to avoid possible
damage. In order to recharge your iPad,iPhone and iPod through USB ports, please install
MSI Center utility.
1
2 10
9
1 VCC 2 VCC 3 USB0- 4 USB1- 5 USB0+ 6 USB1+ 7 Ground 8 Ground 9 No Pin 10 NC
19Overview of Components Overview of Components
JUSB1: USB 3.2 Gen 2 Type-C Connector This connector allows you to connect USB 3.2 Gen 2 Type-C connector on the front panel. The connector possesses a foolproof design. When you connect the cable, be sure to connect it with the corresponding orientation.
JUSB1
USB Type-C Cable
USB Type-C port on the front panel
JTBT1: Thunderbolt Add-on Card Connector This connector allows you to connect the add-on Thunderbolt I/O card.
1
2 16
15
1 TBT_Force_PWR 2 TBT_S0IX_Entry_REQ 3 TBT_CIO_Plug_Event# 4 TBT_S0IX_Entry_ACK 5 SLP_S3#_TBT 6 TBT_PSON_Override_N 7 SLP_S5#_TBT 8 No pin
9 Ground 10 SMBCLK_VSB 11 DG_PEWake 12 SMBDATA_VSB 13 TBT_RTD3_PWR_EN 14 Ground 15 TBT_Card_DET_R# 16 PD_IRQ#
20 Overview of Components
1
2 12
11
1 SPI Power 2 SPI Chip Select
3 Master In Slave Out (SPI Data) 4 Master Out Slave In
(SPI Data) 5 Reserved 6 SPI Clock 7 Ground 8 SPI Reset 9 Reserved 10 No Pin
11 Reserved 12 Interrupt Request
JTPM1: TPM Module Connector This connector is for TPM (Trusted Platform Module). Please refer to the TPM security platform manual for more details and usages.
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC Mode. PWM Mode fan connectors provide constant 12V output and adjust fan speed with speed control signal. DC Mode fan connectors control fan speed by changing voltage.
Important You can adjust fan speed in BIOS > HARDWARE MONITOR.
1 PWM Mode pin definition
1 Ground 2 +12V 3 Sense 4 Speed Control Signal
Connector Default fan mode Max. current Max. power
CPU_FAN1 PWM mode 2A 24W PUMP_FAN1 PWM mode 3A 36W SYS_FAN1~6 DC mode 1A 12W
1 DC Mode pin definition
1 Ground 2 Voltage Control 3 Sense 4 NC
21Overview of Components Overview of Components
JCI1: Chassis Intrusion Connector This connector allows you to connect the chassis intrusion switch cable.
Normal (default)
Trigger the chassis intrusion event
Using chassis intrusion detector 1. Connect the JCI1 connector to the chassis intrusion switch/ sensor on the
chassis. 2. Close the chassis cover. 3. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration. 4. Set Chassis Intrusion to Enabled. 5. Press F10 to save and exit and then press the Enter key to select Yes. 6. Once the chassis cover is opened again, a warning message will be displayed on
screen when the computer is turned on.
Resetting the chassis intrusion warning 1. Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration. 2. Set Chassis Intrusion to Reset. 3. Press F10 to save and exit and then press the Enter key to select Yes.
JDASH1: Tuning controller Connector This connector is used to connect an optional Tuning Controller module.
1
2 6
5
1 No pin 2 NC 3 MCU_SMB_SCL_M 4 MCU_SMB_SDA_M
5 VCC5 6 Ground
22 Overview of Components
JBAT1: Clear CMOS (Reset BIOS) Jumper There is CMOS memory onboard that is external powered from a battery located on the motherboard to save system configuration data. If you want to clear the system configuration, set the jumpers to clear the CMOS memory.
Keep Data (default)
Clear CMOS/ Reset BIOS
Resetting BIOS to default values 1. Power off the computer and unplug the power cord. 2. Use a jumper cap to short JBAT1 for about 5-10 seconds. 3. Remove the jumper cap from JBAT1. 4. Plug the power cord and power on the computer.
JRAINBOW1~2: Addressable RGB LED connectors The JRAINBOW connectors allow you to connect the WS2812B Individually Addressable RGB LED strips 5V.
CAUTION Do not connect the wrong type of LED strips. The JRGB connector and the JRAINBOW connector provide different voltages, and connecting the 5V LED strip to the JRGB connector will result in damage to the LED strip.
Important The JRAINBOW connector supports up to 75 LEDs WS2812B Individually Address-
able RGB LED strips (5V/Data/Ground) with the maximum power rating of 3A (5V). In the case of 20% brightness, the connector supports up to 200 LEDs.
Always turn off the power supply and unplug the power cord from the power outlet before installing or removing the RGB LED strip.
Please use MSIs software to control the extended LED strip.
1 1 +5V 2 Data 3 No Pin 4 Ground
23Overview of Components Overview of Components
EZ Debug LED These LEDs indicate the status of the motherboard.
CPU — indicates CPU is not detected or fail. DRAM — indicates DRAM is not detected or fail. VGA — indicates GPU is not detected or fail. BOOT — indicates booting device is not detected or fail.
JRGB1: RGB LED connector The JRGB connector allows you to connect the 5050 RGB LED strips 12V.
Important The JRGB connector supports up to 2 meters continuous 5050 RGB LED strips
(12V/G/R/B) with the maximum power rating of 3A (12V). Always turn off the power supply and unplug the power cord from the power outlet
before installing or removing the RGB LED strip. Please use MSIs software to control the extended LED strip.
1 1 +12V 2 G 3 R 4 B
24 Installing OS, Drivers & MSI Center
Installing OS, Drivers & MSI Center Please download and update the latest utilities and drivers at www.msi.com
Installing Windows 10 1. Power on the computer. 2. Insert the Windows 10 installation disc/USB into your computer. 3. Press the Restart button on the computer case. 4. Press F11 key during the computer POST (Power-On Self Test) to get into Boot
Menu. 5. Select the Windows 10 installation disc/USB from the Boot Menu. 6. Press any key when screen shows Press any key to boot from CD or DVD…
message. 7. Follow the instructions on the screen to install Windows 10.
Installing Drivers 1. Start up your computer in Windows 10. 2. Insert MSI Drive disc into the optical drive. 3. Click the Select to choose what happens with this disc pop-up notification,
then select Run DVDSetup.exe to open the installer. If you turn off the AutoPlay feature from the Windows Control Panel, you can still manually execute the DVDSetup.exe from the root path of the MSI Drive disc.
4. The installer will find and list all necessary drivers in the Drivers/Software tab. 5. Click the Install button in the lower-right corner of the window. 6. The drivers installation will then be in progress, after it has finished it will prompt
you to restart. 7. Click OK button to finish. 8. Restart your computer.
MSI Center MSI Center is an application that helps you easily optimize game settings and smoothly use content creation softwares. It also allows you to control and synchronize LED light effects on PCs and other MSI products. With MSI Center, you can customize ideal modes, monitor system performance, and adjust fan speed.
MSI Center User Guide If you would like to know more information about MSI Center, please refer to http://download.msi.com/manual/mb/MSICENTER.pdf or scan the QR code to access.
Important Functions may vary depending on the product you have.
25Installing OS, Drivers & MSI Center UEFI BIOS
UEFI BIOS MSI UEFI BIOS is compatible with UEFI (Unified Extensible Firmware Interface) architecture. UEFI has many new functions and advantages that traditional BIOS cannot achieve, and it will completely replace BIOS in the future. The MSI UEFI BIOS uses UEFI as the default boot mode to take full advantage of the new chipsets capabilities.
Important The term BIOS in this user guide refers to UEFI BIOS unless otherwise noted.
UEFI advantages Fast booting — UEFI can directly boot the operating system and save the BIOS self-
test process. And also eliminates the time to switch to CSM mode during POST. Supports for hard drive partitions larger than 2 TB. Supports more than 4 primary partitions with a GUID Partition Table (GPT). Supports unlimited number of partitions. Supports full capabilities of new devices — new devices may not provide backward
compatibility. Supports secure startup — UEFI can check the validity of the operating system to
ensure that no malware tampers with the startup process.
Incompatible UEFI cases 32-bit Windows operating system — this motherboard supports only 64-bit
Windows 10 operating system. Older graphics card — the system will detect your graphics card. When display a
warning message There is no GOP (Graphics Output protocol) support detected in this graphics card.
Important We recommend that you to replace with a GOP/UEFI compatible graphics card or using integrated graphics from CPU for having normal function.
How to check the BIOS mode? 1. Power on your computer. 2. Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter
Boot Menu message appears on the screen during the boot process. 3. After entering the BIOS, you can check the BIOS Mode at the top of the screen.
BIOS Mode: UEFI
26 UEFI BIOS
BIOS Setup The default settings offer the optimal performance for system stability in normal conditions. You should always keep the default settings to avoid possible system damage or failure booting unless you are familiar with BIOS.
Important BIOS items are continuously update for better system performance. Therefore, the
description may be slightly different from the latest BIOS and should be for reference only. You could also refer to the HELP information panel for BIOS item description.
The BIOS screens, options and settings will vary depending on your system.
Entering BIOS Setup Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter Boot Menu message appears on the screen during the boot process.
Function key F1: General Help F2: Add/ Remove a favorite item F3: Enter Favorites menu F4: Enter CPU Specifications menu F5: Enter Memory-Z menu F6: Load optimized defaults F7: Switch between Advanced mode and EZ mode F8: Load Overclocking Profile F9: Save Overclocking Profile F10: Save Change and Reset* F12: Take a screenshot and save it to USB flash drive (FAT/ FAT32 format only). Ctrl+F: Enter Search page
* When you press F10, a confirmation window appears and it provides the modification information. Select between Yes or No to confirm your choice.
BIOS User Guide If youd like to know more instructions on setting up the BIOS, please refer to http://download.msi.com/manual/mb/Intel500BIOS.pdf or scan the QR code to access.
27UEFI BIOS UEFI BIOS
Resetting BIOS You might need to restore the default BIOS setting to solve certain problems. There are several ways to reset BIOS:
Go to BIOS and press F6 to load optimized defaults. Short the Clear CMOS jumper on the motherboard.
Important Be sure the computer is off before clearing CMOS data. Please refer to the Clear CMOS jumper section for resetting BIOS.
Updating BIOS Updating BIOS with M-FLASH Before updating: Please download the latest BIOS file that matches your motherboard model from MSI website. And then save the BIOS file into the USB flash drive. Updating BIOS: 1. Insert the USB flash drive that contains the update file into the USB port. 2. Please refer the following methods to enter flash mode.
Reboot and press Ctrl + F5 key during POST and click on Yes to reboot the system.
Reboot and press Del key during POST to enter BIOS. Click the M-FLASH button and click on Yes to reboot the system.
3. Select a BIOS file to perform the BIOS update process. 4. When prompted click on Yes to start recovering BIOS. 5. After the flashing process is 100% completed, the system will reboot
automatically.
28 UEFI BIOS
Updating the BIOS with MSI Center Before updating:
Make sure the LAN driver is already installed and the internet connection is set properly.
Please close all other application software before updating the BIOS. To update BIOS: 1. Install and launch MSI Center and go to Support page. 2. Select Live Update and click on Advance button. 3. Select the BIOS file and click on Install button. 4. The installation reminder will appear, then click the Install button on it. 5. The system will automatically restart to update BIOS. 6. After the flashing process is 100% completed, the system will restart
automatically.
Updating BIOS with Flash BIOS Button 1. Please download the latest BIOS file that matches your motherboard model from
the MSI website. 2. Rename the BIOS file to MSI.ROM, and save it to the root of your USB flash drive. 3. Connect the power supply to CPU_PWR1 and ATX_PWR1. (No need to install
CPU and memory.) 4. Plug the USB flash drive that contains the MSI.ROM file into the Flash BIOS Port
on the rear I/O panel. 5. Press the Flash BIOS Button to flash BIOS, and the LED starts flashing. 6. The LED will be turned off when the process is completed.
1< 1>
…………………………………………………………………………………………….3
…………………………………………………………………………………………………….4
I/O ………………………………………………………………………………………10 LAN LED ………………………………………………………………………………..10 …………………………………………………………………………………….10
…………………………………………………………………………………………11 CPU …………………………………………………………………………………………………….12 DIMM …………………………………………………………………………………………………..13 PCI_E1~4: PCIe ……………………………………………………………………………..14 JFP1, JFP2: …………………………………………………………………………15 JAUD1: …………………………………………………………………………….15 SATA1~6: SATA 6Gb/s ………………………………………………………………………..16 M2_1~2: M.2 (Key M) ……………………………………………………………………………..16 ATX_PWR1, CPU_PWR1~2, PCIE_PWR1: ………………………………………….17 JUSB1~2: USB 2.0 ……………………………………………………………………………..18 JUSB3~4: USB 3.2 Gen 1 5Gbps …………………………………………………………..18 JUSB1: USB 3.2 Gen 2 Type-C …………………………………………………………….19 JTBT1: ……………………………………………………………………19 CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: ………………………………………….20 JTPM1: TPM ……………………………………………………………………………….20 JCI1: …………………………………………………………………………………..21 JDASH1: ……………………………………………………………………….21 JBAT1: CMOS (Reset BIOS) ………………………………………………………….22 JRAINBOW1~2: RGB LED ……………………………………………22 JRGB1: RGB LED ……………………………………………………………………………….23 EZ LED ……………………………………………………………………………………………..23
OS, & ………………………………………………………….24 Windows 10 …………………………………………………………………………………..24 …………………………………………………………………………………………24 MSI ……………………………………………………………………………………………………..24
UEFI BIOS ………………………………………………………………………………………….25 BIOS () ……………………………………………………………………………………..26
MSI Z590 PRO WIFI (CEC) . , , BIOS .
2
BIOS ……………………………………………………………………………………………………26 BIOS ……………………………………………………………………………………………………27 BIOS() ………………………………………………………………………………..27
3
(ESD)
. . ,
.
. ESD
. ESD , .
.
.
. , .
.
. . . PSU PSU
. . . . , .
. . . . .
60C(140F) . .
4
CPU
10 , 11 , *
LGA1200 * intel.com .
Z590
DDR4 4, 128GB* 1R 2133/ 2666/ 2933 MHz (10 CPU)(by JEDEC &
POR) 1R 2133/ 2666/ 2933/ 3200 MHz (11 CPU)(by
JEDEC & POR) :
1DPC 1R 5333 MHz 1DPC 2R 4700+ MHz 2DPC 1R 4400+ MHz 2DPC 2R 4000+ MHz
non-ECC, un-buffered (XMP)
* http://www.msi.com .
4x PCIe x16 x16/ x1/ x4/ x1 PCI_E1 (CPU)
PCIe 4.0 (11 CPU) PCIe 3.0 (10 CPU)
PCI_E2 & PCI_E4 (Z590 ) PCIe 3.0 x1
PCI_E3 (Z590 ) PCIe 3.0 x4
Realtek ALC897
7.1- HD
-GPU 2-Way AMD CrossFire
5
1x HDR HDMI 2.0b, 4K 60Hz */** 1x 1.4 , 4K 60Hz */**
* . ** CPU .
LAN 1x I225-V 2.5Gbps LAN
LAN &
Wi-Fi 6E AX210 M.2 (Key-E) . MU-MIMO TX/RX, 2.4GHz/ 5GHz/ 6GHz* (160MHz)
2.4Gbps 802.11 a/ b/ g/ n/ ac/ ax 5.2**, FIPS, FISMA
* Wi-Fi 6E 6GHz WIN10 21H1 . ** 5.2 WIN10 21H1 .
</
Table of Contents
- Safety Information
- Specifications
- Rear I/O Panel
- Overview of Components
- CPU Socket
- DIMM Slots
- JFP1, JFP2: Front Panel Connectors
- JAUD1: Front Audio Connector
- SATA1~6: SATA 6Gb/s Connectors
- M2_1~3: M.2 Slot (Key M)
- ATX_PWR1, CPU_PWR1~2, PCIE_PWR1: Power Connectors
- JUSB1~2: USB 2.0 Connectors
- JUSB3~4: USB 3.2 Gen 1 5Gbps Connector
- JUSB1: USB 3.2 Gen 2 Type-C Connector
- JTBT1: Thunderbolt Add-on Card Connector
- CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors
- JTPM1: TPM Module Connector
- JCI1: Chassis Intrusion Connector
- JCOM1: Serial Port Connector
- JDASH1: Tuning controller Connector
- JBAT1: Clear CMOS (Reset BIOS) Jumper
- JRAINBOW1~2: Addressable RGB LED connectors
- JRGB1: RGB LED connector
- EZ Debug LED
- Installing OS, Drivers & MSI Center
- Installing Drivers
- MSI Center
- UEFI BIOS
- Incompatible UEFI cases
- BIOS Setup
- Entering BIOS Setup
- Resetting BIOS
- Updating BIOS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Thank you for purchasing the MSI® Z590 PRO WIFI/ Z590-A PRO motherboard. This
User Guide gives information about board layout, component overview, BIOS
setup and software installation.
Safety Information
- The components included in this package are prone to damage from electrostatic discharge (ESD). Please adhere to the following instructions to ensure successful computer assembly.
- Ensure that all components are securely connected. Loose connections may cause the computer to not recognize a component or fail to start.
- Hold the motherboard by the edges to avoid touching sensitive components.
- It is recommended to wear an electrostatic discharge (ESD) wrist strap when handling the motherboard to prevent electrostatic damage. If an ESD wrist strap is not available, discharge yourself of static electricity by touching another metal object before handling the motherboard.
- Store the motherboard in an electrostatic shielding container or on an anti-static pad whenever the motherboard is not installed.
- Before turning on the computer, ensure that there are no loose screws or metal components on the motherboard or anywhere within the computer case.
- Do not boot the computer before installation is completed. This could cause permanent damage to the components as well as injury to the user.
- If you need help during any installation step, please consult a certified computer technician.
- Always turn off the power supply and unplug the power cord from the power outlet before installing or removing any computer component.
- Keep this user guide for future reference.
- Keep this motherboard away from humidity.
- Make sure that your electrical outlet provides the same voltage as is indicated on the PSU, before connecting the PSU to the electrical outlet.
- Place the power cord such a way that people can not step on it. Do not place anything over the power cord.
- All cautions and warnings on the motherboard should be noted.
- If any of the following situations arises, get the motherboard checked by service personnel:
• Liquid has penetrated into the computer.
• The motherboard has been exposed to moisture.
• The motherboard does not work well or you can not get it work according to
user guide.
• The motherboard has been dropped and damaged.
• The motherboard has obvious sign of breakage.
• Do not leave this motherboard in an environment above 60°C (140°F), it may
damage the motherboard.
Specifications
CPU| • Supports 10th Gen Intel® Core™ Processors, 11th Gen Intel® CoreTM
Processors, Pentium® Gold and Celeron® Processors
• Processor socket LGAl200
—|—
| • Please go to intel.com for compatibility information
Chipset| Intel® Z590 chipset
Memory| • 4x DDR4 memory slots, support up to 128GB
• Supports 1R 2133/ 2666/ 2933 MHz for 10th Gen Intel® CPU (by JEDEC & PORI
• Supports 1R 2133/ 2666/ 2933/ 3200 MHz for 11th Gen Intel® CPU (by JEDEC &
PORI
• Max overclocking frequency:
• 1DPC 1R Max speed up to 5333 MHz
• 1 DPC 2R Max speed up to 4700+ MHz
• 2DPC 1R Max speed up to 4400+ MHz
• 2DPC 2R Max speed up to 4000+ MHz
• Supports Dual-Channel mode
• Supports non-ECC, un-buffered memory
• Supports Intel® Extreme Memory Profile (XMP)
Please refer www.msi.com for more information on compatible memory
Expansion Slots| • 2x PCIe x16 slots
• Support x16/ x4
• PCI_E1 (from CPU)
▪ Supports up to PCIe 4.0 for 11th Gen Intel® CPU
▪ Supports up to PCIe 3.0 for 10th Gen Intel® CPU
• PCI_E3 (from Z590 chipset)
• Supports up to PCIe 3.0
• 2x PCIe 3.0 x1 slots (from Z590 chipset)
Audio| Realtek® ALC897 Codec
• 7.1-Channel High Definition Audio
Multi-GPU| • Supports 2-Way AMD CrossFire™ Technology
Onboard Graphics| • 1x HDMI 2.0b with HDR port, supports a maximum resolution
of 4K 60Hz /*
• 1x DisplayPort 1.4 port, supports a maximum resolution of 4K 60Hz /**
- Available only on processors featuring integrated graphics.
* Graphics specifications may vary depending on the CPU installed.
—|—
LAN| 1x Intel® I225-V 2.5Gbps LAN controller
Wireless LAN & Bluetooth® (Only for Z590 PRO WIFI)| Intel® Wi-Fi 6E AX210
• The Wireless module is pre-installed in the M.2 (Key-E) slot
• Supports MU-MIMO TX/RX, 2.4GHz/ 5GHz/ 6GHz (160MHz) up to 2.4Gbps
• Supports 802.11 a/ b/ g/ n/ ac/ ax
• Supports Bluetooth® 5.2**, FIPS, FISMA - Wi-Fi 6E 6GHz may depend on every country’s regulations and will be ready in WIN10 21H1.
Bluetooth 5.2 will be ready in WIN10 21H1.
Storage| • 6x SATA 6Gb/s ports (from Z590 chipset)
• 3x M.2 slots (Key M)
• M2_1 slot (from CPU)
▫ Available only on 11th Gen Intel® CPU
▫ Supports up to PCIe 4.0×4
▫ Supports 2242/ 2260/ 2280/ 22110 storage devices
• M2_2, M2_3 slots (from Z590 chipset)
▫ Support up to PCIe 3.0×4
▫ Support up to SATA 6Gb/s
▫ Support 2242/ 2260/ 2280 storage devices
▫ Intel® Optane™ Memory Ready***
• Support Intel® Smart Response Technology for Intel Core™ processors - SATA2 will be unavailable when installing M.2 SATA SSD in the M2_2 slot.
** SATA5 & SATA 6 will be unavailable when installing M.2 SSD in the M2_3
slot.
*** Before using Intel® Optane™ memory modules, please ensure that you have
updated the drivers and BIOS to the latest version from MSI website.
RAID| • Supports RAID 0, RAID 1, RAID 5 and RAID 10 for SATA storage devices
• Supports RAID 0 and RAID 1 for M.2 NVMe storage devices
—|—
USB| • Intel® Z590 Chipset
▪ 1x USB 3.2 Gen 2×2 20Gbps Type-C port on the back panel
▪ 2x USB 3.2 Gen 2 10Gbps ports (1 Type-C internal connector and 1 Type-A port
on the back panel)
▪ 6x USB 3.2 Gen 1 5Gbps ports (2 Type-A ports on the back panel, and 4 ports
are available through the internal USB 3.2 Gen 1 5Gbps connectors)
• USB 2.0 Hubs GL850G
▪ 4x USB 2.0 Type-A ports on the back panel
▪ 4x USB 2.0 ports are available through the internal USB 2.0 connectors
Internal Connectors| • 1x 24-pin ATX main power connector
• 1x 8-pin ATX 12V power connector
• 1x 4-pin ATX 12V power connector
• 1x 6-pin ATX PCIe power connector
• 6x SATA 6Gb/s connectors
• 3x M.2 slots (M-Key)
• 1x USB 3.2 Gen 2 10Gbps Type-C port
• 2x USB 3.2 Gen 1 5Gbps connectors (supports additional 4 USB 3.2 Gen 1 5Gbps
ports)
• 2x USB 2.0 connectors (supports additional 4 USB 2.0 ports)
• 1x 4-pin CPU fan connector
• 1x 4-pin water-pump fan connector
• 6x 4-pin system fan connectors
• 1x Front panel audio connector
• 2x System panel connectors
• 1x Chassis Intrusion connector
• 1x Clear CMOS jumper
• 1x TPM module connector
• 1x Serial port connector
• 1x Tuning controller connector
• 1x TBT connector (Supports RTD3)
LED Features| • 1x 4-pin RGB LED connector
• 2x 3-pin RAINBOW LED connectors
• 4x EZ Debug LED
—|—
Back Panel Connectors| • 1x Flash BIOS Button
• x PS/2 keyboard/ mouse combo port
• 4x USB 2.0 Type-A ports
• 1x DisplayPort
• 1x HDMI port
• 1x LAN (RJ45) port
• 2x USB 3.2 Gen 1 5Gbps Type-A ports
• 1x USB 3.2 Gen 2 10Gbps Type-A port
• 1x USB 3.2 Gen 2×2 20Gbps Type-C port
• 2x Wi-Fi Antenna connectors (Only for Z590 PRO WIFI)
• 6x audio jacks
I/O Controller| NUVOTON NCT6687-R Controller Chip
Hardware Monitor| • CPU/ System/ Chipset temperature detection
• CPU/ System/ Pump fan speed detection
• CPU/ System/ Pump fan speed control
Form Factor| • ATX Form Factor
• 12 in. x 9.6 in. (30.5 cm x 24.4 cm)
BIOS Features| • 1x 256 Mb flash
• UEFI AMI BIOS
• ACPI 6.2, SMBIOS 3.0
• Multi-language
Software| • Drivers
• MSI Center
• Intel® Extreme Tuning Utility
• CPU-Z MSI GAMINGv Google Chrome™, Google Toolbar, Google Drive
• Norton™ Internet Security Solution
MSI Center Features| • Mystic Light
• LAN Manager
• User Scenario
• Hardware Monitor
• Frozr AI Cooling
• True Color
• Live Update
• Speed Up
• Smart Tool
• Super Charger
—|—
Special Features| • Audio
▪ Audio Boost
• Network
▪ 2.5G LAN
▪ LAN Manager
▪ Intel WiFi (Z590 PRO WIFI)
• Cooling
▪ Extended Heatsink Design
▪ M.2 Shield Frozr
▪ K7 thermal pad
▪ Choke pad
▪ Pump Fan
▪ Smart Fan Control
• LED
▪ Mystic Light Extension (RAINBOW/RGB)
▪ Mystic Light SYNC
▪ EZ LED Control
▪ EZ DEBUG LED
Special Features| • Performance
▪ Lightning Gen 4 PCI-E Slot
▪ Lightning Gen 4 M.2
▪ Multi GPU-CrossFire Technology
▪ DDR4 Boost
▪ Core Boost
▪ Lightning USB 20G
▪ USB 3.2 Gen 2 10G
▪ USB with Type A+C
▪ Front USB Type-C
▪ Dual CPU Power
▪ Supplemental PCIE Power Connector
▪ 2oz Copper thickened PCB
• Protection
▪ PCI-E Steel Armor
• Experience
▪ MSI Center
▪ Frozr AI Cooling
▪ Click BIOS 5
▪ Flash BIOS Button
Rear I/O Panel
LAN Port LED Status Table
Audio Ports Configuration
Overview of Components
- Distance from the center of the CPU to the nearest DIMM slot. Overview of Components 11
CPU Socket
Please install the CPU into the CPU socket as shown below.
Important
- Always unplug the power cord from the power outlet before installing or removing the CPU.
- Please retain the CPU protective cap after installing the processor. MSI will deal with Return Merchandise Authorization (RMA) requests if only the motherboard comes with the protective cap on the CPU socket.
- When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink is necessary to prevent overheating and maintain system stability.
- Confirm that the CPU heatsink has formed a tight seal with the CPU before booting your system.
- Overheating can seriously damage the CPU and motherboard. Always make sure the cooling fans work properly to protect the CPU from overheating. Be sure to apply an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to enhance heat dissipation.
- Whenever the CPU is not installed, always protect the CPU socket pins by covering the socket with the plastic cap.
- If you purchased a separate CPU and heatsink/ cooler, Please refer to the documentation in the heatsink/ cooler package for more details about installation.
DIMM Slots
Please install the memory module into the DIMM slot as shown below.
Memory module installation recommendation
Important
- Always insert memory modules in the DIMMA2 slot first.
- To ensure system stability for Dual channel mode, memory modules must be of the same type, number and density.
- Some memory modules may operate at a lower frequency than the marked value when overclocking due to the memory frequency operates dependent on its Serial Presence Detect (SPD). Go to BIOS and find the DRAM Frequency to set the memory frequency if you want to operate the memory at the marked or at a higher frequency.
- It is recommended to use a more efficient memory cooling system for full DIMMs installation or overclocking.
- The stability and compatibility of installed memory module depend on installed CPU and devices when overclocking.
- Please refer www.msi.com for more information on compatible memory.
PCI_E1~4: PCIe Expansion Slots
Important
- When adding or removing expansion cards, always turn off the power supply and unplug the power supply power cable from the power outlet. Read the expansion card’s documentation to check for any necessary additional hardware or software changes.
- If you install a large and heavy graphics card, you need to use a tool such as MSI Gaming Series Graphics Card Bolster to support its weight to prevent deformation of the slot.
- For a single PCIe x16 expansion card installation with optimum performance, using the PCI_E1 slot is recommended.
JFP1, JFP2: Front Panel Connectors
These connectors connect to the switches and LEDs on the front panel.
JAUD1: Front Audio Connector
This connector allow you to connect audio jacks on the front panel.
SATA1~6: SATA 6Gb/s Connectors
These connectors are SATA 6Gb/s interface ports. Each connector can connect to
one SATA device.
Important
- SATA2 will be unavailable when installing M.2 SATA SSD in the M2_2 slot.
- SATA5 & SATA 6 will be unavailable when installing M.2 SSD in the M2_3 slot.
- Please do not fold the SATA cable at a 90-degree angle. Data loss may result during transmission otherwise.
- SATA cables have identical plugs on either sides of the cable. However, it is recommended that the flat connector be connected to the motherboard for space saving purposes.
M2_1~3: M.2 Slot (Key M)
Please install the M.2 solid-state drive (SSD) into the M.2 slot as shown
below.
ATX_PWR1, CPU_PWR1~2, PCIE_PWR1: Power Connectors
These connectors allow you to connect an ATX power supply.
| 1| +3.3V| 13| +3.3V
—|—|—|—|—
2| +3.3V| 14| -12V
3| Ground| 15| Ground
4| +5V| 16| PS-ON#
5| Ground| 17| Ground
6| +5V| 18| Ground
7| Ground| 19| Ground
8| PWR OK| 20| Res
9| 5VSB| 21| +5V
10| +12V| 22| +5V
11| +12V| 23| +5V
12| +3.3V| 24| Ground
| 1| Ground| 5| +12V
—|—|—|—|—
2| Ground| 6| +12V
3| Ground| 7| +12V
4| Ground| 8| +12V
| 1| Ground| 3| +12V
—|—|—|—|—
2| Ground| 4| +12V
| 1| +12V| 5| Ground
—|—|—|—|—
2| +12V| 6| Ground
3| +12V| 7| Ground
Important
Make sure that all the power cables are securely connected to a proper ATX
power supply to ensure stable operation of the motherboard.
JUSB1~2: USB 2.0 Connectors
These connectors allow you to connect USB 2.0 ports on the front panel.
| 1| VCC| 2| VCC
—|—|—|—|—
3| USB0-| 4| USB1-
5| USB0+| 6| USB1+
7| Ground| 8| Ground
9| No Pin| 10| NC
Important
- Note that the VCC and Ground pins must be connected correctly to avoid possible damage.
- In order to recharge your iPad,iPhone and iPod through USB ports, please install MSI Center utility.
JUSB3~4: USB 3.2 Gen 1 5Gbps Connector
This connector allows you to connect USB 3.2 Gen 1 5Gbps ports on the front
panel.
| 1| Power| 11| USB2.0+
—|—|—|—|—
2| USB3_RX_DN| 12| USB2.0-
3| USB3_RX_DP| 13| Ground
4| Ground| 14| USB3_TX_C_DP
5| USB3_TX_C_DN| 15| USB3_TX_C_DN
6| USB3_TX_C_DP| 16| Ground
7| Ground| 17| USB3_RX_DP
8| USB2.0-| 18| USB3_RX_DN
9| USB2.0+| 19| Power
10| Ground| 20| No Pin
Important
Note that the Power and Ground pins must be connected correctly to avoid
possible damage.
JUSB1: USB 3.2 Gen 2 Type-C Connector
This connector allows you to connect USB 3.2 Gen 2 Type-C connector on the
front panel. The connector possesses a foolproof design. When you connect the
cable, be sure to connect it with the corresponding orientation.
JTBT1: Thunderbolt Add-on Card Connector
This connector allows you to connect the add-on Thunderbolt I/O card.
| 1| TBT_Force_PWR| 2| TBT_S0IX_Entry_REQ
—|—|—|—|—
3| TBT_CIO_Plug_Event#| 4| TBT_S0IX_Entry_ACK
5| SLP_S3#_TBT| 6| TBT_PSON_Override_N
7| SLP_S5#_TBT| 8| Net Name
9| Ground| 10| SMBCLK_VSB
11| DG_PEWake| 12| SMBDATA_VSB
13| TBT_RTD3_PWR_EN| 14| Ground
15| TBT_Card_DET_R#| 16| PD_IRQ#
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors
Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC
Mode. PWM Mode fan connectors provide constant 12V output and adjust fan speed
with speed control signal. DC Mode fan connectors control fan speed by
changing voltage.
| Connector | Default fan mode | Max. current | Max. power |
|---|---|---|---|
| CPU_FAN1 | PWM mode | 2A | 24W |
| PUMP_FAN1 | PWM mode | 3A | 36W |
| SYS_FAN1~6 | DC mode | 1A | 12W |
1| Ground| 2| +12V
3| Sense| 4| Speed Control Signal
1| Ground| 2| Voltage Control
3| Sense| 4| NC
Important
You can adjust fan speed in BIOS > HARDWARE MONITOR.
JTPM1: TPM Module Connector
This connector is for TPM (Trusted Platform Module). Please refer to the TPM
security platform manual for more details and usages.
| 1| SPI Power| 2| SPI Chip Select
—|—|—|—|—
3| Master In Slave Out (SPI Data)| 4| Master Out Slave In
(SPI Data)
5| Reserved| 6| SPI Clock
7| Ground| 8| SPI Reset
9| Reserved| 10| No Pin
11| Reserved| 12| Interrupt Request
JCI1: Chassis Intrusion Connector
This connector allows you to connect the chassis intrusion switch cable.
Using chassis intrusion detector
- Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis.
- Close the chassis cover.
- Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.
- Set Chassis Intrusion to Enabled.
- Press F10 to save and exit and then press the Enter key to select Yes.
- Once the chassis cover is opened again, a warning message will be displayed on screen when the computer is turned on.
Resetting the chassis intrusion warning
- Go to BIOS > SETTINGS > Security > Chassis Intrusion Configuration.
- Set Chassis Intrusion to Reset.
- Press F10 to save and exit and then press the Enter key to select Yes.
JCOM1: Serial Port Connector
This connector allows you to connect the optional serial port with bracket.
| 1| DCD| 2| SIN
—|—|—|—|—
3| SOUT| 4| DTR
5| Ground| 6| DSR
7| RTS| 8| CTS
9| RI| 10| No Pin
JDASH1: Tuning controller Connector
This connector is used to connect an optional Tuning Controller module.
| 1| No pin| 2| NC
—|—|—|—|—
3| MCU_SMB_SCL_M| 4| MCU_SMB_SDA_M
5| VCC5| 6| Ground
JBAT1: Clear CMOS (Reset BIOS) Jumper
There is CMOS memory onboard that is external powered from a battery located
on the motherboard to save system configuration data. If you want to clear the
system configuration, set the jumpers to clear the CMOS memory.
Resetting BIOS to default values
- Power off the computer and unplug the power cord.
- Use a jumper cap to short JBAT1 for about 5-10 seconds.
- Remove the jumper cap from JBAT1.
- Plug the power cord and power on the computer.
JRAINBOW1~2: Addressable RGB LED connectors
The JRAINBOW connectors allow you to connect the WS2812B Individually
Addressable RGB LED strips 5V.
| 1| +5V| 2| Data
—|—|—|—|—
3| No Pin| 4| Ground
CAUTION
Do not connect the wrong type of LED strips. The JRGB connector and the
JRAINBOW connector provide different voltages, and connecting the 5V LED strip
to the JRGB connector will result in damage to the LED strip.
Important
- The JRAINBOW connector supports up to 75 LEDs WS2812B Individually Addressable RGB LED strips (5V/Data/Ground) with the maximum power rating of 3A (5V). In the case of 20% brightness, the connector supports up to 200 LEDs.
- Always turn off the power supply and unplug the power cord from the power outlet before installing or removing the RGB LED strip.
- Please use MSI’s software to control the extended LED strip.
JRGB1: RGB LED connector
The JRGB connector allows you to connect the 5050 RGB LED strips 12V.
| 1| +12V| 2| G
—|—|—|—|—
3| R| 4| B
Important
- The JRGB connector supports up to 2 meters continuous 5050 RGB LED strips (12V/G/R/B) with the maximum power rating of 3A (12V).
- Always turn off the power supply and unplug the power cord from the power outlet before installing or removing the RGB LED strip.
- Please use MSI’s software to control the extended LED strip.
EZ Debug LED
These LEDs indicate the status of the motherboard.
CPU – indicates CPU is not detected or fail.
DRAM – indicates DRAM is not detected or fail.
VGA – indicates GPU is not detected or fail.
BOOT – indicates booting device is not detected or fail.
Installing OS, Drivers & MSI Center
Please download and update the latest utilities and drivers at www.msi.com
Installing Windows® 10
- Power on the computer.
- Insert the Windows® 10 installation disc/USB into your computer.
- Press the Restart button on the computer case.
- Press F11 key during the computer POST (Power-On Self Test) to get into Boot Menu.
- Select the Windows® 10 installation disc/USB from the Boot Menu.
- Press any key when screen shows Press any key to boot from CD or DVD… message.
- Follow the instructions on the screen to install Windows® 10.
Installing Drivers
- Start up your computer in Windows® 10.
- Insert MSI® Drive disc into the optical drive.
- Click the Select to choose what happens with this disc pop-up notification, then select Run DVDSetup.exe to open the installer. If you turn off the AutoPlay feature from the Windows Control Panel, you can still manually execute the DVDSetup.exe from the root path of the MSI Drive disc.
- The installer will find and list all necessary drivers in the Drivers/Software tab.
- Click the Install button in the lower-right corner of the window.
- The drivers installation will then be in progress, after it has finished it will prompt you to restart.
- Click OK button to finish.
- Restart your computer.
MSI Center
MSI Center is an application that helps you easily optimize game settings and
smoothly use content creation softwares. It also allows you to control and
synchronize LED light effects on PCs and other MSI products. With MSI Center,
you can customize ideal modes, monitor system performance, and adjust fan
speed.
MSI Center User Guide
If you would like to know more information about MSI Center, please refer to
MSICENTER
[PDF] or scan the QR code to access it.
Important
Functions may vary depending on the product you have.
24 Installing OS, Drivers & MSI Center
UEFI BIOS
MSI UEFI BIOS is compatible with UEFI (Unified Extensible Firmware Interface)
architecture. UEFI has many new functions and advantages that traditional BIOS
cannot achieve, and it will completely replace BIOS in the future. The MSI
UEFI BIOS uses UEFI as the default boot mode to take full advantage of the new
chipset’s capabilities.
Important
The term BIOS in this user guide refers to UEFI BIOS unless otherwise noted.
UEFI advantages
- Fast booting – UEFI can directly boot the operating system and save the BIOS selftest process. And also eliminates the time to switch to CSM mode during POST.
- Supports for hard drive partitions larger than 2 TB.
- Supports more than 4 primary partitions with a GUID Partition Table (GPT).
- Supports unlimited number of partitions. Supports full capabilities of new devices – new devices may not provide backward compatibility.
- Supports secure startup – UEFI can check the validity of the operating system to ensure that no malware tampers with the startup process.
Incompatible UEFI cases
- 32-bit Windows operating system – this motherboard supports only 64-bit Windows 10 operating system.
- Older graphics card – the system will detect your graphics card. When display a warning message There is no GOP (Graphics Output protocol) support detected in this graphics card.
Important
We recommend that you to replace with a GOP/UEFI compatible graphics card or
using integrated graphics from CPU for having normal function. How to check
the BIOS mode?
- Power on your computer.
- Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter Boot Menu message appears on the screen during the boot process.
- After entering the BIOS, you can check the BIOS Mode at the top of the screen.
BIOS Mode: UEFI
BIOS Setup
The default settings offer the optimal performance for system stability in
normal conditions. You should always keep the default settings to avoid
possible system damage or failure booting unless you are familiar with BIOS.
Important
- BIOS items are continuously update for better system performance. Therefore, the description may be slightly different from the latest BIOS and should be for reference only. You could also refer to the HELP information panel for BIOS item description.
- The BIOS screens, options and settings will vary depending on your system.
Entering BIOS Setup
Press Delete key, when the Press DEL key to enter Setup Menu, F11 to enter
Boot Menu message appears on the screen during the boot process.
Function key
F1: General Help
F2 : Add/ Remove a favorite item
F3: Enter Favorites menu
F4: Enter CPU Specifications menu
F5: Enter Memory-Z menu
F6: Load optimized defaults
F7: Switch between Advanced mode and EZ mode
F8: Load Overclocking Profile
F9: Save Overclocking Profile
F10: Save Change and Reset*
F12: Take a screenshot and save it to USB flash drive (FAT/ FAT32 format
only). Ctrl+F: Enter Search page
- When you press F10, a confirmation window appears and it provides the modification information. Select between Yes or No to confirm your choice.
BIOS User Guide
If you’d like to know more instructions on setting up the BIOS, please refer
to Intel500BIOS [PDF] or scan the QR code to
access it.
Resetting BIOS
You might need to restore the default BIOS setting to solve certain problems.
There are several ways to reset BIOS:
- Go to BIOS and press F6 to load optimized defaults.
- Short the Clear CMOS jumper on the motherboard.
- Press the Clear CMOS button on the rear I/O panel.
Important
Be sure the computer is off before clearing CMOS data. Please refer to the
Clear CMOS jumper/ button section for resetting BIOS.
Updating BIOS
Updating BIOS with M-FLASH
Before updating:
Please download the latest BIOS file that matches your motherboard model from
MSI website. And then save the BIOS file into the USB flash drive. Updating
BIOS:
-
Insert the USB flash drive that contains the update file into the USB port.
-
Please refer the following methods to enter flash mode.
• Reboot and press Ctrl + F5 key during POST and click on Yes to reboot the
system.
• Reboot and press Del key during POST to enter BIOS. Click the M-FLASH button
and click on Yes to reboot the system. -
Select a BIOS file to perform the BIOS update process.
-
When prompted click on Yes to start recovering BIOS.
-
After the flashing process is 100% completed, the system will reboot automatically.
Updating the BIOS with MSI Center
Before updating:
- Make sure the LAN driver is already installed and the internet connection is set properly.
- Please close all other application software before updating the BIOS. To update BIOS:
1. Install and launch MSI Center and go to Support page.
2. Select Live Update and click on Advance button.
3. Select the BIOS file and click on Install button.
4. The installation reminder will appear, then click the Install button on
it.
5. The system will automatically restart to update BIOS.
6. After the flashing process is 100% completed, the system will restart
automatically.
Updating BIOS with Flash BIOS Button
- Please download the latest BIOS file that matches your motherboard model from the MSI® website.
- Rename the BIOS file to MSI.ROM, and save it to the root of your USB flash drive.
- Connect the power supply to CPU_PWR1 and ATX_PWR1. (No need to install CPU and memory.)
- Plug the USB flash drive that contains the MSI.ROM file into the Flash BIOS Port on the rear I/O panel.
- Press the Flash BIOS Button to flash BIOS, and the LED starts flashing.
- The LED will be turned off when the process is completed.
Copyright
mis Micro-Star Int’l Co.,Ltd.
Copyright © 2021 All rights reserved.
The MSI logo used is a registered trademark of Micro-Star Int’l Co., Ltd. All
other marks and names mentioned may be trademarks of their respective owners.
No warranty as to accuracy or completeness is expressed or implied. MSI
reserves the right to make changes to this document without prior notice.
Revision History
Version 1.0, 2021/01, First release.
Version 1.1, 2021/01, updated release.
Version 1.2, 2021/02, updated release.
Technical Support
If a problem arises with your system and no solution can be obtained from the
user guide, please contact your place of purchase or local distributor.
Alternatively, please try the following help resources for further guidance.
∙ Visit the MSI website for technical guide, BIOS updates, driver updates, and
other information: http://www.msi.com
∙ Register your product at: http://register.msi.com
Regulatory Notices v
References
- MSI — Redirect
- dtsc.ca.gov/hazardouswaste/
- MSI — Redirect
- csr
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>
Download This Manual (PDF format)
Download this manual >>