Dynamic 320 start инструкция

INSTRUCTION MANUAL

BATTERY CHARGER

Cod.954838

BATTERY CHARGER AND STARTER

EXPLANATION OF DANGER, MANDATORY AND PROHIBITION SIGNS.

| DANGER OF EXPLOSION
—|—
| GENERAL HAZARD
| DANGER OF CORROSIVE SUBSTANCES
| Symbol indicating separation of electrical and electronic appliances for
refuse collection. The user is not allowed to dispose of these appliances as
solid, mixed urban refuse, and must do it through authorised refuse collection
centres.

GUARANTEE AND CONFORMITY

1. GENERAL SAFETY RULES FOR THE USE

– During the charge the battery produces explosive gases, avoid the formation
of flames and sparkes. DO NOT SMOKE.
– Position the batteries to be charged in a well-ventilated place.

– Inexperience and untrained people should be properly instructed before using
the appliance.
– This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
– Children shall not play with the appliance.
– Cleaning and user maintenance shall not be made by children without
supervision.
– Use the battery charger only indoors and make sure that you start it in airy
places. DO NOT SET IN THE RAIN OR SNOW.
– Disconnect the mains cable before connecting to or disconnecting the
charging cables from the battery.
– Do not connect or disconnect the clamps to or from the battery with the
battery charger operating.
– Never use the battery charger inside the car or in the bonnet.
– Substitute the mains cable only with an original one.
– If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
– Do not use the battery charger to charge batteries which are not
rechargeable.
– Make sure the available power supply voltage corresponds to that shown on
the battery charger rating plate.
– To prevent damaging the vehicle electronics, scrupulously respect the
warnings given by the producer of the vehicle or the batteries used.
– This battery charger has components such as switches and relays which can
cause arcs or sparks. Therefore when using it in a garage or in a similar
place set the battery charger in a suitable case.
– Repair or maintenance of the inside of the battery charger can be executed
only by skilled technicians.
– WARNING: ALWAYS DISCONNECT THE POWER SUPPLY CABLE FROM THE MAINS BEFORE
CARRYING OUT ANY SIMPLE MAINTENANCE OPERATION ON THE BATTERY CHARGER.
– The battery charger is protected from indirect contact by an earth wire as
indicated for class I equipment. Make sure the power outlet is protected by an
earth connection.
– For models supplied without plugs, connect plugs having a capacitance
suitable for the value of the fuse shown in the plate; for models supplied
with cable and plug and with a ”P.MAX START” power higher than 9kW, when used
for starting, we advise replacing the plug with one having a capacitance
suitable for the fuse shown in the plate.

2. GENERAL DESCRIPTION

2.1 TRADITIONAL BATTERY CHARGERS

Manual battery chargers (the operator must intervene to stop the charge
process) indicated for charging free electrolyte lead acid batteries (WET)
used in engine-driven vehicles (petrol and diesel), motorcycles, boats, etc.
6V, 12V and 24V batteries can be recharged according to the available output
voltage. Some models have the START or the BOOST&GO mode to start engine-
driven vehicles.
Rechargeable batteries according to the output voltage available: 6V / 3
cells; 12V / 6 cells; 24V / 12 cells.

2.2 AUTOMATIC BATTERY CHARGERS (TRONIC)

Automatic battery chargers (electronic control of the charging process,
interruption and automatic reset) suitable for charging sealed batteries (GEL,
AGM) in the TRONIC mode, and free electrolyte lead acid batteries (WET) in the
manual CHARGE mode (see par. 2.1), used with engine-driven vehicles (petrol
and diesel), motorcycles, boats, etc. It is possible to recharge 12V and 24V
batteries.

3. BOOST – BOOST&GO FUNCTIONS

These functions speed up charging and help vehicle starting thanks to fast
battery pre-charge (the charging time depends on the battery capacity and
discharge level). When using models with the BOOST&GO function, vehicles can
be started up with the cables still connected to the battery (see paragraph
7). During the charging process, always follow the indications given in
paragraph 4.

4. AMMETER READING (FIG. A)

The ammeter allows reading the current supplied by the battery charger to the
battery (a completely flat battery initially requires maximum current which
lowers over time). During the charging phase the ammeter indicator moves from
right to left, indicating a decrease in the current required by the battery
until very low levels (near to zero) are reached (fully charged battery), at a
speed and with an accuracy that depend on the capacity, battery state and
ammeter reading precision. Please remember that the exact charge status of the
battery can only be determined by using a densimeter which allows measurement
of the specific gravity of the electrolyte. With manual battery chargers, the
ammeter must be monitored to determine when the battery has finished charging.
Once the battery is charged it must be disconnected to prevent overheating or
damage.

5. INSTALLATION

5.1 ASSEMBLY (FIG. B)

Unpack the battery charger and assemble the separate parts contained in the
package. Models on wheels are to be set in a vertical position.

5.2 POSITIONING THE BATTERY CHARGER

During operation, position the battery charger on a stable surface and make
sure that there is no obstruction to air passage through the openings provided
to ensure sufficient ventilation.

5.3 CONNECTION TO THE MAIN SUPPLY

– The battery charger should be connected only and exclusively to a power
source with the neutral lead connected to earth. Check that the mains voltage
is the same as the voltage of the equipment.
– Check that the power supply is protected by systems such as fuses or
automatic switches, sufficient to support the maximum absorption of the
equipment.
– The connection to the main supply has to be made using a suitable cable.
– If you put an extension to the primary cable, the section should be adequate
and, in any case, never less than that of the cable supplied.
– You always have to earth the equipment with the yellow/green wire contained
in the main cable, indicated by the label (W), while the other two wires
should be connected to the phase and the neutral cable.

6. OPERATION DURING CHARGING

NB: Before charging check that the capacity of the battery (Ah) which is to
be charged, is not inferior to that reported on the data table of the battery
charger (C min). Follow the instructions, taking great care to respect the
order given below.

6.1 BATTERY PREPARATION

When recharging a WET-type battery, proceed as follows:
– Remove the caps of the battery charger (if foreseen) so as to let the gas
produced go out. Check that the level of the electrolyte covers the plates of
the battery. If these were not covered add distilled water and cover them up
to 5-10 mm.

WARNING: USE THE MAXIMUM CAUTION DURING THIS OPERATION AS THE ELECTROLYTE
IS A HIGHLY CORROSIVE ACID.

6.2 BATTERY CHARGER/BATTERY CONNECTION

– Make sure the power cable is disconnected from the mains.
– With models having more than one charge voltage, turn the deviator or the
switch to the selected charge voltage. If there is no deviator or switch,
suitably connect the red crocodile clip (+ symbol) to the specific battery
charger terminal in correspondence with the selected charge voltage.
– Connect the red charge clamp to the positive terminal of the battery ( +
symbol). If the symbols are indistinguishable remember that the positive
terminal is the one not connected to the vehicle chassis.
– Connect the black charge clamp to the vehicle chassis, at a safe distance
from the battery and the fuel pipe.
NOTE: if the battery is not installed in the vehicle, connect the clamp
directly to the negative terminal of the battery (- symbol).

6.3 MANUAL CHARGING AND AUTOMATIC CHARGING

NOTE: the Ah values, if given beside the pushbuttons, are purely
indicative (because the charging process depends on how flat the battery is)
and they suggest the position for charging an initially flat battery with
capacity within the indicated range, in under 15 hours. It is not advisable to
go below the minimum values that are indicated.

6.3.1 MANUAL CHARGE ( )
Recommended method for free electrolyte lead acid batteries (WET).
– Carefully follow the instructions given in paragraphs 6.1 and 6.2.
– Move the deviator (if present) to the BATTERY symbol.
– Turn the charge adjustment deviator/deviators or switch (if present) (FIG.
C) the normal charge position (BATTERY symbol) or fast charge position (BOOST)
as required (with some models the switch also acts as a power switch).
– If the battery charger has a TIMER a maximum pre-set charge time can be set
(FIG. C).
– Power the battery charger by inserting the power supply cable into the power
outlet and turning the switch (if present) to ON.
– Monitor the ammeter as described in paragraph 4.
NOTE: Once the WET battery is charged, you may note the liquid inside
starting to “boil”. It is advisable to stop charging when this phenomenon
appears so as to prevent damage to the battery.

6.3.2 AUTOMATIC CHARGING (TRONIC)
We recommend using models with the TRONIC mode to charge sealed batteries
(GEL, AGM).
– Carefully follow the instructions given in paragraphs 6.1 and 6.2.
– Turn the deviator to TRONIC and the charge adjustment switch to the normal
charge position (BATTERY symbol) or fast charge position (BOOST) as required
(FIG. C).
– Power the battery charger by inserting the power cable into the mains
socket. The battery charger controls the voltage present at the battery
terminals, automatically interrupting the current being supplied when the
battery is charged (the ammeter indicator positions itself at zero) and
supplying it again automatically when the battery begins running down. The
TRONIC mode is ideal for automatically maintaining the battery charged (AGM
and WET) without the risk of damaging it.

6.4 SIMULTANEOUS CHARGING OF SEVERAL BATTERIES

WARNING; do not simultaneously charge different types of batteries or
batteries with different capacities or levels of discharge. If you have to
charge more than one battery at the same time you can connect them “in series”
or “in parallel” (FIG. D).
For “parallel” connection batteries must have the same nominal voltage (Volt),
which corresponds to the battery charger output voltage, and the total of Ah
must be within the charge range of the battery charger.
For “serial” connection batteries must have the same capacity (Ah) and the sum
of the nominal voltages of all the batteries must correspond to the battery
charger output voltage.

6.5 END OF CHARGE

– Remove the power supply from the battery charger by turning the switch to
OFF (if present) and/or removing the power supply cable from the mains outlet.
– Disconnect the black charge clamp from the chassis of the vehicle or from
the negative terminal of the battery (- symbol).
– Disconnect the red charge clamp from the positive terminal of the battery (+
symbol).
– Store the battery charger in a dry place.
– Close up the battery cells with the appropriate plugs (if present).

6.6 MAINTENANCE (enabled in TRONIC or PULSE TRONIC mode only)

– Leave the battery charger connected to the mains.
– Do not interrupt the charge process.
– Leave the charge clamps connected to the battery even after the charge
process has been completed.
The battery charger will automatically interrupt and reboot the charge phase
maintaining the battery voltage within the product default voltage range.

7. OPERATION DURING STARTING

WARNING: Before proceeding with starting follow the vehicle manufacturer’s
instructions carefully!
– Make sure the power line is protected by fuses or automatic circuit breakers
with sizes as indicated on the rating plate by the ( ) symbol.
– To make starting easier, quickly charge for 10-15 minutes at the BOOST/
BOOST&GO position (see paragraph 6.3.1).
– In order to prevent overheating in the battery charger, ALWAYS carry out the
starting operation according to the duty cycle (work/pause) as indicated on
the appliance (e.g. START 3s ON 120s OFF-5 CYCLES). Do not insist if the
engine does not start: this could cause serious damage to the battery or even
to the electrical equipment in the vehicle. If the engine does not start, wait
a few minutes and then repeat the rapid charge operation.

7.1 BATTERY CHARGER/BATTERY CONNECTION

– With the power cable disconnected from the mains, if necessary, turn the
deviator to 12V or 24V or suitably connect the red crocodile clip to the
specific battery charger terminal, according to the nominal voltage of the
battery of the vehicle to be started.
– Make sure the battery is connected properly to the respective (+ and -)
terminals, and that it is in good condition (not sulphated or dud). Never ever
start vehicles with the batteries disconnected from their respective
terminals; the presence of the battery is essential for the elimination of
possible overvoltage.

7.2 STARTING UP WITH START (FIG. E1)

– With the battery charger at OFF, plug in the power cable.
– Turn the switch, if present, to ON.
– Turn the switch to START and turn the ignition key to start up the engine.

7.3 STARTING UP WITH BOOST&GO (FIG. E2)

– Turn the switch to BOOST&GO.
– Power the battery charger by inserting the power cable into the mains
socket.
– Start up the vehicle by turning the ignition key.

7.4 END OF STARTING

– Disconnect the power to the battery charger by turning the switch (if
present) to OFF and remove the power cable from the mains.
– Disconnect the black crocodile clip from the negative battery terminal (-
symbol) and the red crocodile clip from the positive battery terminal (+
symbol).
– Store the battery charger in a dry place.

8. BATTERY CHARGER PROTECTION (FIG. F)

The battery charger protects itself from:
– Overcharge (too much current supplied to the battery).
– Short-circuit (loading clips placed in contact with each other).
– Polarity inversion on the battery clamps.
For appliances fitted with fuses, if the fuses have to be replaced always use
the same kind of fuse with the same rated size.
WARNING: If the replacement fuse has a different size from that shown on the
rating plate it could cause damage to people or property. For the same reason,
never ever replace the fuse with a bridge in copper or other material.
The power supply cable should always be DISCONNECTED from the mains supply
while the fuse is being changed.
When replacing the ribbon fuse, if present, carefully fasten the nuts.

9. USEFUL ADVICE

– If the positive and negative terminals are incrusted with oxide, clean them
to ensure good contacts with the clamps.
– Never ever allow the two clamps to come into contact when the battery
charger is connected to the mains. In this case the fuse will blow.
– If the battery, to which this battery charger is to be connected, is
permanently installed in the vehicle, also consult the vehicle manufacturer’s
user’s and maintenance handbook under the “ELECTRICAL SYSTEM” or “MAINTENANCE”
section.

Fig. A

Fig. B

Pincer with red handle connected to the movable cable. Pincer with black
handle connected to the fixed cable which comes out directly out of the
battery charger.

Fig. C

  Positions: normal charge
BOOST Positions: rapid charge

  BOOST
1            1

Картинка с сайта: manualspro.net

TRONIC        |    CHARGE
  BOOST  |      BOOST
1            1         |     1            1

  BOOST
2            1

  BOOST
3            1

6

  BOOST
3            1

  BOOST
3            1

Fig. D

SERIES

Картинка с сайта: manualspro.net

PARALLEL

Картинка с сайта: manualspro.net

Fig. E

E1

E2

Fig. F

GUARANTEE

The manufacturer guarantees proper operation of the machines and undertakes to
replace free of charge any parts should they be damaged due to poor quality of
materials or manufacturing defects within 12 months of the date of
commissioning of the machine, when proven by certification. Returned machines,
also under guarantee, should be dispatched CARRIAGE PAID and will be returned
CARRIAGE FORWARD. This with the exception of, as decreed, machines considered
as consumer goods according to European directive 1999/44/EC, only when sold
in member states of the EU. The guarantee certificate is only valid when
accompanied by an official receipt or delivery note. Problems arising from
improper use, tampering or negligence are excluded from the guarantee.
Furthermore, the manufacturer declines any liability for all direct or
indirect damages.

CERTIFICATE OF GUARANTEE

MOD. /

………………………….
Date of buying

НОМЕ

Sales company (Name and Signature)

The product is in compliance with:

DIRECTIVES

LVD 2014/35/EU + Amdt.

Documents / Resources

|
TELWIN Dynamic 320 Start Mobile Battery
Charger
[pdf] Instruction Manual
12-24V — 45-30A, Starthj lp 180A, Dynamic 320, Dynamic 320 Start Mobile
Battery Charger, Start Mobile Battery Charger, Mobile Battery Charger, Battery
Charger, Charger
—|—

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>